Product Description
eng
Resetting
1. Press and hold the button for 10 seconds.
Release the button immediately when
the LED ashes green. You now have 60
seconds to reset the device.
2. Press the button again and hold it.
3. While you are holding the button down, the
LED ashes yellow once, then two times in
a row, and nally numerous times in a row.
4. Release the button while the LED is ashing
numerous times in a row.
5. After you release the button, the LED shows
one long ash, and the reset is completed.
As an alternative option, you can reset the
device by removing the screws in the back of
the device and open the casing (note that you
need a T6 Torx screwdriver to install and remove
these screws). Remove the battery and insert it
again. You now have 60 seconds to reset the
device. Press the button inside the device and
follow steps 3-5.
Fault nding and cleaning
• In case of a bad or weak wireless signal,
change the location of the Panic Button.
Otherwise you can relocate your gateway
or strengthen the signal with a smart plug.
• If the search for a gateway has timed out, a
short press on the button will restart it.
Battery replacement
The device will ash twice every minute when
the battery is low.
CAUTION: RISK OF EXPLOSION IF THE BAT-
TERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF THE BATTERY IN ACCORDANCE
WITH INSTRUCTIONS.
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside.
To replace the battery, remove the screws in
the back of the device and open the casing
(note that you need a T6 Torx screwdriver to
install and remove these screws). Replace
the battery (CR2450) respecting the polarities.
Close the casing and install the screws in the
back of the device.
Disposal
Dispose the product and batteries properly at
the end of their lives. This is electronic waste
which should be recycled.
Mounting and use
• If your product includes a necklace, the
necklace is already attached to the Panic
Button and ready to wear around your neck.
If you do not wish to use the necklace,
simply cut it o.
Precautions
• Do not remove the product label as it
contains important information.
• When mounting with tape, make sure the
surfaces are clean and dry.
• When mounting with tape, the room
temperature should ideally be between 21°
C and 38° C and minimum 16° C.
• Avoid mounting with tape on rough, porous
or bered materials such as wood or
cement, as they reduce the tape bond
• Do not ingest battery, Chemical Burn
Hazard.
Alarm
Product description
The Panic Button communicates wirelessly
through a Zigbee network, and it has multi-
ple mounting and use options. If a necklace
or strap is included, you can wear the Panic
Button around your neck or on your arm. Alter-
natively, you can use it hand-held as a remote
control or mount it on the wall or door with tape.
Version 2.1
INSTALLATION MANUAL
Panic Button
• If your product includes a strap for the wrist,
you can attach the button to the strap and
wear it on your arm.
• If you want to mount the Panic Button on
the wall, you can use the included tape. Put
the double adhesive tape on the back of
the device and press rmly on the device
with the tape to make it stick to the wall.
To activate the alarm, press the button. The red
LED will then start ashing, signaling that the
alarm is activated.
To disable the alarm, press the button for 3
seconds. When the alarm is disabled, the red
LED will stop ashing.
Connecting
• Press the button to activate search for
network. The Panic Button will start
searching (up to 15 minutes) for a Zigbee
network to join.
• Make sure that the Zigbee network is open
for joining devices and will accept the Panic
Button.
• While the device is searching for a Zigbee
network to join, the yellow LED ashes.
• When the LED stops ashing, the device
has successfully joined the Zigbee network.
• If the scanning has timed out, a short press
on the button will restart it.
a.
b.
c.
d.
e.
• This product contains a coin cell battery. If
the cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can
lead to death.
• Keep new and used batteries away from
children.
• If the battery compartments does not close
securely, stop using the product and keep
it away from children.
• If you think batteries might have been
swallowed or placed inside any part of the
body, seek immediate medical attention.
CAUTION
• Disposal of a battery into re or a hot oven,
or mechanically crushing or cutting of a
battery, that can result in an explosion;
• Leaving a battery in an extremely high
temperature surrounding environment that
can result in an explosion or the leakage of
ammable liquid or gas;
• A battery subjected to extremely low air
pressure that may result in an explosion or
the leakage of ammable liquid or gas.
FCC statement
Changes or modications to the equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.