Nailer/Stapler Operation Manual Specifications MODEL NO. Max. P.S.I. Operating Pressure Range Air Inlet Weight Height Length Width Type of Fastener NF2502X4 120 70-120 SNC1002X4 120 70-120 1/4" NPT 4.66 10.25 11.75 3 Finish Nail 16 Gauge 1/4" NPT 2.3 7.5 11.3 2.25 Narrow Crown Staple 18 Gauge Fastener Lengths Fastener Capacity See page 17 110 pcs. See page 18 150 pcs. NB2002X4 NB1252X4 120 120 70-120 70-120 1/4" NPT 2.6 8.1 9 2 Brad Nail 18 Gauge NBSNC2X4 120 57-110 1/4" NPT 2.55 7.75 9.75 2.
TABLE OF CONTENTS Page Tool Specifications ................................................................ Front Cover Table of Contents ................................................................................... 2 Limited Warranty ..................................................................................... 3 Safety Guidelines & Warning Chart ....................................................... 4 Lubrication and Maintenance ..............................................................
LIMITED WARRANTY ONE YEAR FROM DATE OF PURCHASE All merchandise manufactured by DeVilbiss Air Power Company/ExCell Manufacturing is warranted to be free of defects in workmanship and material which occur during the first year from the date of purchase by the original purchaser (initial user). Products covered under this warranty include: air compressors, *air tools, accessories, service parts, pressure washers, and generators used in consumer applications (i.e., personal residential household usage only).
SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use symbols to the right. Please read the manual and pay attention to these sections. URGENT SAFETY INFORMATION - A HAZARD THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE. Information for preventing damage to equipment.
Risk of head injury. HAZARD TO LOOK FOR Injury to eyes, head and hearing WHAT COULD HAPPEN HOW TO PREVENT IT Metal fragments, fasteners, or other material could be projected against head or into eyes resulting in serious injury or property damage. Continued exposure to an operating tool can result in permanent hearing damage. Always wear ANSI approved Z87 safety glasses, Z89.1 head protection and S3.19 hearing protection. Risk of puncture injury.
Risk from flying objects. HAZARD TO LOOK FOR WHAT COULD HAPPEN Injury to self or others in the work area. Fasteners could ricochet or be propelled causing serious injury or property damage. When working along edges or next to voids in work surface, the contact trip safety mechanism could be depressed and allow the tool to discharge a fastener into the air or through thin work materials resulting in serious injury or property damage.
LUBRICATION AND MAINTENANCE 2. Turn the tool so the air inlet is facing up and put one drop of DeVilbiss AC230 Air Tool Oil, high speed spindle oil, such as Unocal RX22, or 3-in-1 oil into the air inlet. DO NOT USE detergent oil or additives. Operate the tool briefly after adding oil. (See Figure 1) DO NOT OVER LUBRICATE AIR TOOL. Do not store the tool in cold weather. Frost or ice can form on the operating valves or mechanisms and the tool may not operate correctly. 3.
Figure 3 Regulator Air Flow Always connect the Female Quick Coupler to the air hose. Never connect the Female Quick Coupler to the tool. Oiler Filter NOTE Excessive oil will damage o-rings and seal of tool. If in-line oiler is used, manual lubrication through the air inlet is not required on a daily basis. Never carry the tool by the hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil, and sharp edges. Replace any damaged, weak or worn hoses.
RECOMMENDED HOOK-UP The following illustration shows the proper hook-up which will help prolong the life of the Tool. NAILER MALE QUICK CONNECTOR (Supplied with Tool) MALE QUICK CONNECTOR FEMALE QUICK COUPLER AIR HOSE (3/8" I.D.) OILER FILTER FEMALE QUICK COUPLER AIR COMPRESSOR CONTACT TRIP SAFETY MECHANISM 2X4 CONTRACTOR SERIES Do not hold the tool against the work surface with extra force. Allow the tool to drive the fastener.
OPERATING A CONTACT TRIP TOOL: 1. Requires finger to be off the trigger and the nose of the Tool to be placed on the work surface. 2. The contact trip safety mechanism is then depressed against the work surface and the trigger pulled to drive a fastener. 3. The trigger is released after each fastener is driven. 4. Move the tool to the next desired fastener location and repeat the procedure above.
NOTE Use DeVilbiss Air Power fasteners or equivalent for proper performance of tool. See page 17-20 for fastener information. Handle the tool carefully. Respect the tool as a working implement and always assume the tool contains fasteners: a. Never use the tool as a toy and engage in horseplay. b. Never aim or point the tool at anyone. The tool may contain fasteners. c. Always keep people and animals at a safe distance from the work area in case of accidental discharge of fasteners. d.
4. Push release button (if equipped) and slide feeder shoe forward. Release Button Feeder OPERATING THE TOOL READ THIS MANUAL AND UNDERSTAND ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE OPERATING TOOL. Disconnect tool from air compressor before adjusting, clearing jams, servicing, relocating and during non-operation. Failure to do so could result in serious injury or property damage. Protect your eyes and ears. Wear Z87 safety glasses with side shields. Wear hearing protection.
CLEARING A JAM FROM THE TOOL 3. Remove fasteners from magazine. 4. NF2502X4, SNC1002X4, NB2002X4, and NB1252X4 Lift nose cover latch to unlatch and remove driver guide cover. Nose Cover Latch Disconnect tool from air compressor before adjusting, clearing jams, servicing, relocating and during non-operation. FASTENER JAMMED IN FASTENER DISCHARGE AREA: NBSNC2x4 1. Disconnect tool from air hose. Loosen the screws on the driver guide cover and then remove the driver guide cover. 2.
FASTENER JAM INSIDE MAGAZINE: SNC1002x4 Pull feeder shoe back into "locked" position. 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the magazine latch to open the magazine. Magazine Latch Feeder 3. Remove jammed fasteners. 4. Reload fasteners into magazine. Refer to Loading the Tool section in this manual.
TROUBLESHOOTING GUIDE Stop using the Tool immediately if any of the following occur. Serious personal injury could occur. Warranty repairs or replacements must be performed by a DeVilbiss Air Power Authorized Service Center Only. PROBLEM CAUSE SOLUTION Air leaking at trigger valve area. Seals in trigger valve housing are damaged. Seals must be replaced & operation of Contact trip must be checked. On the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Trigger Repair Kit.
TROUBLESHOOTING GUIDE (cont'd) PROBLEM Fasteners are jammed in tool. Nailer/Stapler misfires or sinks two nails/staples at the same time. Air leak near top of tool. Sluggish operation. Air leak near bottom of CAUSE Worn/damaged feed pawl. Replace feed pawl. Contact an *AWSC Worn/damaged feed pawl spring. Replace feed pawl spring. Fasteners are not correct size. Fasteners recommended for tool must be used. Fasteners are bent. Replace with undamaged fasteners. Nail height setting incorrect.
NF2502X4 SAFETY GLASSES 1/4" NPT INLET PLUG (AC100) LUBRICATING OIL 6 & 7MM COMBINATION CRESCENT WRENCH FINISH NAIL FASTENERS FINISH NAILER 3 4 5mm ALLEN WRENCHES 11/ 4” 11/2” 13/4” 2” 21/4” 21/2” Tool Range 21/2” Tool NF2502X4 2X4 Part Number Description Qty per Box NFF12525 NFF15025 NFF17525 NFF20025 NFF22525 NFF25025 1-1/4" Finish 1-1/2" Finish 1-3/4" Finish 2" Finish 2-1/4" Finish 2-1/2" Finish 2500 2500 2500 2500 2500 2500 PAGE 17 Steel Driver Series Comparable Part 7T32 7T38 7T4
SNC1002X4 SAFETY GLASSES NARROW CROWN STAPLE FASTENER Tool SNC1002X4 3&4 ALLEN WRENCHES 1/4" NPT INLET PLUG LUBRICATING (AC100) OIL NARROW CROWN STAPLER 2X4 Part Number Description Qty per Box Steel Driver Series Comparable Part SNCF06350 SNCF07550 SNCF10050 5/8" Staple 3/4" Staple 1" Staple 5000 5000 5000 2L16 2L19 2L25 PAGE 18
NB2002X4 SAFETY GLASSES LUBRICATING OIL BRAD NAIL FASTENERS 4 3 ALLEN WRENCHES 1/4" NPT INLET Plug (AC100) BRAD NAILER 5/8" Tool NB2002X4 2X4 Part Number Description Qty per Box NBF07550 NBF10050 NBF12550 NBF15050 NBF17550 NBF20050 3/4" Brad 1" Brad 1-1/4" Brad 1-1/2" Brad 1-3/4" Brad 2" Brad 5000 5000 5000 5000 5000 5000 PAGE 19 Steel Driver Series Comparable Part 4F20 4F25 4F32
NB1252X4 SAFETY GLASSES 4MM 3MM ALLEN WRENCHES LUBRICATING OIL BRAD NAIL FASTENERS 1/4" NPT INLET PLUG (AC100) Tool NB1252X4 BRAD NAILER 2X4 Part Number Description Qty per Box Steel Driver Series Comparable Part NBF06350 NBF07550 NBF10050 NBF12550 5/8" Brad 3/4" Brad 1" Brad 1-1/4" Brad 5000 5000 5000 5000 4F16 4F20 4F25 4F32 PAGE 20
NBSNC2X4 NARROW CROWN STAPLE & BRAD NAIL FASTENERS LUBRICATING OIL 2X4 SIGNATURE SAFETY GLASSES 4MM 3MM ALLEN WRENCHES COMBINATION BRAD NAILER/ NARROW CROWN STAPLER 1/2" 3/8” 5/8” 3/4” 1” 11/4” 3/4" 1" 1-1/4" 1-1/2" 11/2” 1/4" Tool Range Tool NBSNC2X4 Tool Range 11/ 2” 2X4 Part Number SNCF06350 SNCF07550 SNCF10050 SNCF12550 SNCF15050 NBF06350 NBF07550 NBF10050 NBF12550 NBF15050 Description Qty per Box 5/8" Staple 3/4" Staple 1" Staple 1-1/4" Staple 1-1/2" Staple 5/8" Brad 3/4" Brad 1" B
REPAIR KITS AVAILABLE NF2502X4 K-0521 Top Repair Kit K-1664 Driver Blade Kit K-0522 Bottom Repair Kit K-0523 Trigger Repair Kit SNC1002X4 and NB1252X4 K-0525 Top Repair Kit K-9025 Driver Blade Kit for SNC1002x4 K-1832 Drive Blade Kit for NB1252x4 K-0526 Bottom Repair Kit K-0527 Trigger Repair Kit PAGE 22
REPAIR KITS AVAILABLE NB2002X4 K-0517 Top Repair Kit K-1850 Driver Blade Kit K-0518 Bottom Repair Kit K-0519 Trigger Repair Kit NBSNC2X4 B340-06 Top Repair Kit BN2B-10 Driver Blade Kit B232-23 Bottom Repair Kit B251-02 Trigger Repair Kit PAGE 23
Nailer/Stapler Operation Manual Call our Toll Free Number 1-800-888-2468, Ext 2, then 1, to obtain the location of the nearest Authorized Service Center for ordering repair parts and for warranty repairs. When ordering repair parts from your local Authorized Service Center, always give the following information: • Model number of your product • Part number and description of the item you wish to purchase WARRANTY This product is covered by the DeVilbiss one year limited warranty.