Product Overview

14
TECHNICAL GUIDE – ADHESIVES ©2021 DEWALT – REV. F
Adhesives
A
NCHORS & FASTENERS
STRENGTH DESIGN (SD)
Bond Strength Design Information for Threaded Rods
(For use with load combinations taken from ACI 318-14 Section 5.3)
1,2
Design Information Symbol Units
Nominal Rod Diameter (Inch) / Reinforcing Bar Size
3/8 1/2 5/8 3/4 7/8 1 1-1/4
Minimum embedment h
ef,min
inch
(mm)
2-3/8
(60)
2-3/4
(70)
3-1/8
(79)
3-1/2
(89)
3-1/2
(89)
4
(102)
5
(127)
Maximum embedment h
ef,max
inch
(mm)
4-1/2
(114)
6
(152)
7-1/2
(191)
9
(229)
10-1/2
(267)
12
(305)
15
(381)
122°F (50°C)
Maximum Long-Term
Service Temperature;
176°F (80°C)
Maximum Short-Term
Service Temperature
3,4
Characteristic bond
strength in
cracked concrete
4,7
t
k,cr
psi
(N/mm
2
)
Not
Applicable
498
(3.4)
519
(3.6)
519
(3.6)
519
(3.6)
519
(3.6)
525
(3.6)
Characteristic bond
strength in
uncracked concrete
4,8
t
k,uncr
psi
(N/mm
2
)
823
(5.7)
823
(5.7)
823
(5.7)
823
(5.7)
823
(5.7)
743
(5.1)
588
(4.1)
Not applicable in
water-filled hole
installation condition
162°F (72°C)
Maximum Long-Term
Service Temperature;
248°F (120°C)
Maximum Short-Term
Service Temperature
3,4
Characteristic bond
strength in
cracked concrete
4,7
t
k,cr
psi
(N/mm
2
)
Not
Applicable
245
(1.7)
255
(1.8)
255
(1.8)
255
(1.8)
255
(1.8)
255
(1.8)
Characteristic bond
strength in
uncracked concrete
4,8
t
k,uncr
psi
(N/mm
2
)
405
(2.8)
405
(2.8)
405
(2.8)
405
(2.8)
405
(2.8)
366
(2.5)
Not
Applicable
Not applicable in
water-filled hole
installation condition
Permissible installation
conditions
6
Dry concrete
φ
d
- 0.65 0.65 0.65 0.65
Water-saturated
concrete
φ
ws
- 0.55 0.55 0.55 0.55
Water-filled hole
(flooded)
φ
wf
- 0.45 0.45 0.45 0.45
κ
wf
0.78 0.70 0.69 0.67
Reduction factor for seismic tension
α
N
,seis
- 0.95
For SI: 1 inch = 25.4 mm, 1 psi = 0.006894 MPa. For pound-inch units: 1 mm = 0.03937 inch, 1 MPa = 145.0 psi.
1. Bond strength values correspond to a normal-weight concrete compressive strength f'c = 2,500 psi (17.2 MPa). For concrete compressive strength, f'c between 2,500 psi and 8,000 psi (17.2
MPa and 55.2 MPa), the tabulated characteristic bond strength may be increased by a factor of (f'c / 2,500)
0.13
[For SI: (f'c / 17.2)
0.13
].
2. The modification factor for bond strength of adhesive anchors in lightweight concrete shall be taken as given in ACI 318-14 17.2.6 where applicable.
3. Long-term and short-term temperatures meet the requirements of Section 8.5 of ACI 355.4 and Table 9.1, Temperature Category A.
4. Short-term base material service temperatures are those that occur over brief intervals, e.g. as a result of diurnal cycling. Long-term base material service temperatures are roughly constant
over significant periods of time.
5. Characteristic bond strengths are for sustained loads including dead and live loads.
6. Permissible installation conditions include dry concrete, water-saturated concrete and water-filled holes. Water-filled holes include applications in dry or water-saturated concrete where the
drilled holes contain standing water at the time of anchor installation.
7. For structures assigned to Seismic Design Categories C, D, E or F, the tabulated bond strength values for cracked concrete must be adjusted by an additional reduction factor,
α
N,seis
,
as given in this table.
8. Bond strength values for uncracked concrete are applicable for structures assigned to Seismic Design Categories A and B only.