Product Overview

22
TECHNICAL GUIDE – ADHESIVES ©2021 DEWALT – REV. F
Adhesives
A
NCHORS & FASTENERS
REFERENCE TABLES FOR INSTALLATION
REFERENCE TABLES FOR INSTALLATION
Gel (working) Time and Curing Table
Temperature of Base Material
Gel (working) Time Full Curing Time
˚F ˚C
14 -10 90 minutes 24 hours
23 -5 90 minutes 14 hours
32 0 45 minutes 7 hours
41 5 25 minutes 2 hours
50 10 15 minutes 90 minutes
68 20 6 minutes 45 minutes
86 30 4 minutes 25 minutes
95 35 2 minutes 20 minutes
104 40 1.5 minutes 15 minutes
The gel (working) times listed for 32
o
F to 95
o
F are also applicable for the temperature of the adhesive and use of mixing nozzes during installation.
For installations in base material temperatures between 14
o
F and 23
o
F (-10ºC and -5ºC) the cartridge temperature must be conditioned to between 68
o
F and 95
o
F (20
o
C - 35
o
C).
Hole Cleaning Equipment Selection Table for AC100+ Gold
1,2,3,4
Threaded Rod
Diameter
(inch)
Rebar Size
(no.)
Drill Bit
Diameter
(inch)
Overall
Brush Length, L
(inches)
Steel Wire
Brush
(Cat. #)
Blowout
Tool
Number of
Cleaning Actions
Solid Base Material
3/8 #3 7/16 6-3/4 08284
Hand-pump
(Cat #08280)
or
compressed
air nozzle
4x blowing
4x brushing
4x blowing
1/2 - 9/16 6-3/4 08285
- #4 5/8 6-3/4 08275
5/8 #5 11/16 7-7/8 08286
5/8 #5 3/4 7-7/8 08278
3/4 #6 7/8 7-7/8 08287
7/8 #7 1 11-7/8 08288
Compressed air
nozzle only
1 #8 1-1/8 11-7/8 08289
1-1/4 #9 1-3/8 11-7/8 08290
- #10 1-1/2 11-7/8 08291
Hollow Base Material (with Screen Tube)
1/4 - 3/8 (SS screen) 6-3/4 08284
Hand pump
(Cat# 08280) or
compressed air nozzle
2x blowing
2x brushing
2x blowing
1/4 - 1/2 (plastic screen) 6-3/4 08284
3/8 - 1/2 (SS screen) 6-3/4 08284
3/8 - 9/16 (plastic screen) 6-3/4 08285
1/2 #3 5/8 (SS screen) 6-3/4 08275
1/2 - 3/4 (plastic screen) 7-7/8 08278
5/8 #4 3/4 (SS screen) 7-7/8 08278
5/8 - 7/8 (plastic screen) 7-7/8 08287
3/4 #5 7/8 (SS screen) 7-7/8 08287
15/16 #6 1 (SS screen) 11-7/8 08288
1. An SDS-plus adaptor (Cat. #08283) or Jacobs chuck style adaptor (Cat. #08296) is required to attach a steel wire brush to the drill tool.
2. A brush extension (Cat. #08282) must be used for holes drilled deeper than the listed brush length.
3. See ordering information for selection of piston plugs (where applicable).
4. For any case, it must be possible for the steel anchor element to be inserted into the cleaned hole without resistance.
See separate installation details in this section for 'Retrofit Bolt Anchors in URM Walls': threaded Rods and Reinforcing Bars or Rebar Dowel with AC100+ Gold Installed in Unreinforced Masonry
Walls with Stainless Steel Screen Tubes.