ANCHORS & FASTENERS Adhesive Anchor Installation System HIGH PERFORMANCE FEATURED BASIC AC200+™ AC100+ Gold® AC50™ Pure110+® Pure50+™ PureGP™
ANCHORS && FASTENERS FASTENERS ANCHORS Introducing The First Cordless
Adhesive Anchor Installation System 3
ANCHORS && FASTENERS FASTENERS ANCHORS PRODUCTIVITY * OSHA COMPLIANT ICC-ES APPROVED RELIABLE INSTALLATION 4 * S ystem is compliant to the Exposure Control Methods described in Table 1 of 29 CFR 1926.1153 when outlined components are operating and maintained in accordance to manufacturer's instructions.
HIGH PERFORMANCE ■ Suitable □ May Be Suitable BASE MATERIAL INSTALLATION TEMP.
ANCHORS & FASTENERS + ESR-4027 Conforms to AC308 / ACI 355.
AC200+ ™ Acrylic Adhesive Anchoring System Permissible Installation Conditions Lorem ipsum 104˚F 14˚F Dispensing Configurations QuikShot 1:1 Mixing Ratio Dual Cartridge 10:1 Mixing Ratio High Performance Bond Strength AC200+™ vs.
ANCHORS & FASTENERS + ESR-3298 ASTM C 881 Type I, II, IV & V Grade 3 (Class B&C) F120 CODE LISTED ICC-ES ESR-3298 SEISMIC approved for seismic design categories A-F ICC-ES APPROVED approved for cracked and uncracked concrete, and seismic applications BOND STRENGTH high bond strength at 110˚F; no reduction in bond strength due to service temperature shifts VERSATILE dispensing options 1:1 and 3:1 Competitive Comparison DEWALT Pure110+® Hilti RE500-V3 Simpson SET-3G Red Head Epcon C6+ ESR-3298
Pure110+ ® Epoxy Adhesive Anchoring System TOPAZ Permissible Installation Conditions Dispensing Configurations Quik-Shot 1:1 Mixing Ratio Dual Cartridge 1:1 Mixing Ratio 104˚F 41˚F Dual Cartridge 3:1 Mixing Ratio High Performance Bond Strength Pure110+® vs. Hilti RE 500 V3 vs.
ANCHORS & FASTENERS + ASTM C 881 Type I, II, IV & V Grade 3 (Class A&B) ESR-2582 ESR-3200 ESR-4105 Certified to NSF/ANSI 61 Concrete/Masonry/ Unreinforced Masonry F120 F180 ICC-ES APPROVED approved for cracked and uncracked concrete, grouted or hollow masonry and unreinforced masonry SEISMIC approved for seismic design categories A-F Competitive Comparison, Concrete LOW TEMPERATURE DISPENSING approved for dispensing down to 14˚F Code Approval (Concrete) DEWALT AC100+ Gold® Hilti HY 100 Simpson AT
AC100+ Gold ® Acrylic Adhesive Anchoring System CODE LISTED ICC-ES ESR-2582 ICC-ES ESR-3200 ICC-ES ESR-4105 AC100+ Gold® DOT Approval Alabama Louisiana Ohio Arizona Maine Pennsylvania Arkansas Maryland Rhode Island Colorado Michigan Tennessee Connecticut Minnesota Texas Illinois Mississippi Vermont Indiana Missouri Virginia Iowa Nebraska Washington Kansas New Jersey Wisconsin Kentucky New York Permissible Installation Conditions 8478SD Approved on a Project-By Project Acce
ANCHORS & FASTENERS + ESR-3576 ASTM C 881 Type I, II, IV & V Grade 3 (Class B&C) Concrete ICC-ES APPROVED approved for cracked and uncracked concrete EVALUATED AND RECOGNIZED for long and short term loading Competitive Comparison DEWALT Pure50+™ Code Approvals DESIGNED specifically with road, bridge and concrete contractors in mind EVALUATED AND RECOGNIZED for freeze/thaw performance Normal Weight Concrete 12 Light Weight Concrete No Approval ATC HS 200 Simpson SET-XP No ESR-2508 Approval
Pure50+ ™ Epoxy Adhesive Anchoring System Pure50+™ DOT Approval Alabama Kentucky New Mexico Arizona Louisiana New York Arkansas Maine North Carolina Colorado Maryland Ohio Connecticut Michigan Oklahoma Permissible Installation Conditions Florida Minnesota Rhode Island Georgia Missouri Tennessee Idaho Nebraska Texas Indiana Nevada Utah 08600 Iowa New Jersey Virginia Dispensing 9oz. 20.5oz.
ANCHORS & FASTENERS AC50 PureGP ASTM C 881 Type I, II, IV & V Grade 3 (Class A & B) ASTM C 881 & AASHTO M235, Types I, II, IV and V Grade 3, Classes B & C ™ Acrylic Adhesive Anchoring System ™ Epoxy Adhesive Anchoring System Dispensing Configurations DESIGNED for use with threaded rod and rebar Dual Cartridge 10:1 Mixing Ratio CURES down to 5˚ F Dispensing Configuration Mixing Nozzles 08294 20V MAX* Dispensers DCE595D1 8497 28oz Dual Cartridge 4 4 20V MAX* Dispensers 08494 4 Pneumatic Disp
Cordless Dispensing Tools For Adhesive Cartridges PRODUCTIVE up to 24 tubes per battery charge at room temperature DOSAGE DIAL controls the length of time that the adhesive is being dispensed SPEED DIAL controls the flow rate of the adhesive being dispensed Available Dispensing Configurations Quik-Shot 1:1 Mixing Ratio Dual Cartridge 1:1 Mixing Ratio Dual Cartridge 3:1 Mixing Ratio Dual Cartridge 10:1 Mixing Ratio AVAILABLE IN 4 SIZES DCE591D1* Epoxy Dispenser 1:1 Cartridges DCE593D1* Epoxy Dispens
ANCHORS & FASTENERS 1-9/16" FLEXVOLT® SDS MAX Rotary Hammer DCH481 FLEXVOLT® technology; 60V Max* battery system RECOMMENDED impact energy for SDS Max hollow bits * Maximum initial battery voltage measured without a workload is 60 volts. Nominal voltage is 54.
USE WITH DWV012 for OSHA silica dust Table 1 Compliance SDS MAX Y-CUTTER CARBIDE for positioning and hole starting * S ystem is compliant to the Exposure Control Methods described in Table 1 of 29 CFR 1926.1153 when outlined components are operating and maintained in accordance to manufacturer's instructions.
ANCHORS & FASTENERS CAT # DCH481X2 DCH263R2DH DCH273P2 DCH273P2DH0 DESCRIPTION 1-9/16" Flexvolt® SDS Max* Brushless Combination Hammer w/ 9Ah Battery 1-1/8" D-Handle SDS+ Brushless Rotary Hammer w/Dust Extractor 20V Max* 1" SDS+ Brushless Rotary Hammer w/5Ah Battery 20V Max* 1" SDS+ Brushless Rotary Hammer w/Dust Extractor 20V Max* DCH293R2 1-1/8" SDS+ Brushless Rotary Hammer 3.5J w/ 6Ah Battery 20V Max* DCH293R2DH 1-1/8" SDS+ Brushless Rotary Hammer 3.
Hole Preparation Drilling Tools, Bits & Dust Management SDS Max 4-Cutter Carbide Drill Bits USABLE OVERALL LENGTH LENGTH SDS+ Full Head Carbide Drill Bits CAT # DIA CAT # DW5806 5/8" 8" 13-1/2" DW5809 5/8" 16" 21-1/2" DW5503 3/16" DW5807 5/8" 31" 36" DW5504 DW5808 11/16" 16" 21-1/2" DW5810 3/4" 8" 13-1/2" DW5812 3/4" 16" 21-1/2" DW5813 3/4" 31" 36" DW5814 13/16" 16" 21-1/2" DW5518 1/4" DW5815 7/8" 8" 13-1/2" DW55200 DIA 4-1/2" DW5471 5/8" 8" 10" 4" 6-1
ANCHORS & FASTENERS Adhesive Cartridges CAT # 08310SD 08321SD 08351SD 08313SD 08320SD PFC1271050 PFC1271150 8478SD 8486SD 8490SD 08600 08605 08651 08497 08821 Hole Cleaning Tools and Accessories DESCRIPTION Pure110+ 1:1 Ratio 9oz QS Cartridge Pure110+ 1:1 Ratio 21oz Dual Cartridge Pure110+ 1:1 Ratio 51oz Dual Cartridge Pure110+ 3:1 Ratio 13oz Dual Cartridge Pure110+ 3:1 Ratio 20oz Dual Cartridge AC200+ 10oz QS Cartridge AC200+ 28oz Dual Cartridge AC100+ Gold 10oz QS Cartridge AC100+ Gold 12oz Dual Cartrid
Adhesive Installation Cartridges and Delivery Accessories Adhesive Piston Plugs CAT # Plastic Screen Tubes DESCRIPTION ANSI BIT DIA ROD DIA REBAR SIZE QTY NUMBER DESCRIPTION DRILL DIA QTY 3/8" x 3-1/2" 3/8" x 6" 3/8" x 8" 1/2" x 3-1/2" 1/2" x 6" 5/8" x 6" 3/4" x 6" 9/16" 9/16" 9/16" 3/4" 3/4" 7/8" 1" 25 25 25 25 25 25 10 DESCRIPTION DRILL DIA QTY 07960 1/4" x 2" 3/8" 25 07862 1/4" x 6" 3/8" 25 07864 07856 07961 07962 07963 07964 07959 07857 07965 07966 07967 07968 07858 07969 07970
ANCHORS & FASTENERS Adhesive Installation System: Drill Bits 20V MAX* SDS Plus Rotary Hammers Drill Bits Flexvolt® SDS Max Drill Bits SDS Max Combination Hammer (Corded) Drill Bits DCH481X2 1-9/16" W/ E-CLUTCH D25481K 1-9/16"/ CORDED *For 20V MAX* Maximum initial battery voltage measured without a workload is 20 volts. Nominal voltage is 18.
The System Adhesive Installation System: Hollow Drill Bits 20V MAX* SDS Plus Rotary Hammers Hollow Drill Bit SDS Max Combination Hammer (Corded) Hollow Drill Bit DCH481X2 1-9/16" W/ E-CLUTCH D25481K 1-9/16"/ CORDED ROD/ REBAR SIZE HOLE SIZE EMBD.
Adhesive Anchor Installation System ANCHORS & FASTENERS DEWALT Locations Field Service ALASKA Anchorage 907-561-7181 ALABAMA Mobile 251-602-1000 ARKANSAS North Little Rock ARIZONA Phoenix 602-437-1200 501-372-3040 DEWALT Tool Service Anchor Distribution Ctr.
