Operation Manual

25
ENGLISH
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
.
Fitting a mains plug to 115 V units
(U.K. & Ireland only)
• The plug should be fitted by a competent person.
If you are in doubt, contact an authorized
D
EWALT repair agent or a qualified electrician.
The wires are coloured according to the following
code:
live = brown
neutral = blue
• Do not connect the blue or brown wire to the
earth terminal in the plug. Connect as follows:
brown to terminal marked ‘L’
blue to terminal marked ‘N’
The plug fitted should be comply with BS EN 60309
(BS4343), 32 Amps.
Always ensure that the cable clamp is
correctly and securely fitted to the
sheath of the cable.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (6) and hold the guard
(4) over the tool as shown.
• Align the lugs (7) with the notches (8).
• Press the guard down and rotate it to the
required posiiton.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
Never use the tool without the guard in
place.
Fitting and removing a grinding or cutting disc
(fig. C1 - C3)
• Place the tool on a table, guard up.
• Fit the inner flange (10) correctly onto the spindle
(11) (fig. C1).
• Place the disc (12) on the flange (10) (fig. C2).
When fitting a disc with a raised center, make
sure that the raised centre (13) is facing the
flange (10).
• Screw the outer flange (14) onto the spindle (11)
(fig. C3):
- the ring on the flange (14) must face towards
the disc when fitting a grinding disc (A);
- the ring on the flange (14) must face away from
the disc when fitting a cutting disc (B).
• Press the spindle lock (3) and rotate the spindle
(11) until it locks in position (fig. C2)
• Tighten the flange (14) with the two-pin spanner
supplied.