INSTRUCTION MANUAL D25113-XE, D25114-XE, D25213-XE, D25314-XE, D25315-XE HEAVY-DUTY SDS ROTARY HAMMERS D25330-XE HEAVY-DUTY SDS CHIPPING HAMMER
Components (Fig. 1–4) A. B. C. D. E. F. Side handle Depth rod SDS chuck Trigger switch/Variable speed trigger Forward/reverse control button Lock-on button (D25111-XE, D25113-XE, D25330-XE only) G. Mode selector H. Chisel rotation FIG. 1 C FIG. 2 D25113-XE, D25114-XE B B G A G A D E D25213-XE C E D F Components (Fig. 5–6, page 5) I. Mode selector button J. Sleeve K. Collar FIG. 3 G C B FIG.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. ELECTRICAL SAFETY a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
g. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. SERVICE a. Have your power tool serviced by a qualified repair person using only identical replacement parts.
• • • • • • • • • • • • Wear ear protectors. Exposure to noise can cause hearing loss. Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.Keep a firm grip on the tool at all times. Do not attempt to operate this tool without holding it with both hands. Operating this tool with one hand will result in loss of control. Breaking through or encountering hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before use.
Switch • The label on your tool may include the following symbols. The symbols and their definitions are as follows: V ................. volts A ...............amperes Hz ............... hertz W ..............watts min ............. minutes ...........alternating current no ..............no load speed .......... direct current .............. Class I Construction .............earthing terminal ................... (grounded) .............safety alert symbol ............... Class II Construction …/min .......
D25113-XE, D25114-XE To reverse the rotary hammer, turn it OFF and align the reversing lever (E) with the yellow arrow pointing backward (viewed when holding drill in operating position). To position the lever for forward operation, turn the rotary hammer OFF and align the reversing lever with the yellow arrow pointing forward (viewed when holding drill in operating position). FIG.
Drilling Tools 8. With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skipping out. The machine is intended for hammerdrilling in concrete, brick and stone. It is also suitable for drilling without impact in wood, metal, ceramic and plastic.
ACCESSORIES DRILLING IN MASONRY (D25113-XE, D25114-XE, D25213-XE, D25313-XE, D25314-XE) When drilling in masonry, use SDS carbide tipped bits rated for percussion drilling and be certain that the bit is sharp. Use a constant and firm force on the tool to drill most effectively. A smooth, even flow of dust indicates the proper drilling rate. DEPTH ROD To adjust the depth rod. 1. Push in and hold the button on the side handle. 2.
SPECIFICATIONS This warranty gives you specific legal rights and you may have other rights under the provisions of the Consumer Guarantee Act 1993 (New Zealand only), Trade Practices Act 1974 and State Legislation (Australia only). In addition to the warranty, DEWALT tools are covered by our: FREE ONE YEAR SERVICE CONTRACT DEWALT will also maintain the tool for free at any time during the first year of purchase.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (JAN07) Form No. 495266-04 D25113-XE, D25114-XE, D25213-XE, D25314-XE, D25315-XE, D25330-XE Copyright © 2007 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.