® D25112(K) D25113K D25114K D25213K 1
English 6 Ⱥড় 13 ०༹ዐ࿔ 20 ༹ݏዐ࿔ 27 34 Copyright DE WALT 2
9 7 4 5 4 5 3 1 2 1 6 11 10 D25213K 9 7 6 11 10 D25113K 8 4 D25112(K) D25114K A 3
5 6 B1 7 4 B2 12 5 C 10 9 D 4 E 11
3 3 F1 F2 8 6 13 G 8 H 5
ENGLISH HEAVY DUTY ROTARY HAMMER DEILL D25112(K)/D25113K/D25114K/D25213K Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
ENGLISH D25112(K ) D25113K LpA (sound pressure) dB(A)* 90.5 90.5 LWA (acoustic power) dB(A) 99 99 LpA (sound pressure) dB(A)* 90.5 LWA (acoustic power) dB(A) 99 D25114K * at the operator’s ear Take appropriate measures for the protection of hearing. Weighted root mean square acceleration value according to EN 50144: D25112(K ) D25113K D25114K D25213K 9.2 m/s2 9.2 m/s2 9.2 m/s2 9.
ENGLISH 14 15 16 17 18 19 20 8 The tool will do the job better and safer at the rate for which it was intended. Do not force the tool. Warning! The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury. Check for damaged parts Before use, carefully check the tool and mains cable for damage.
ENGLISH Your DEWALT tool is double insulated in accordance with EN 50144; therefore no earth wire is required. D25113K/D25114K/D25213K (fig. B2) The tool can be used in the following operating modes: Using an extension cable If an extension cable is required, use an approved extension cable suitable for the power input of this tool (see technical data). The minimum conductor size is 1.5 mm2. When using a cable reel, always unwind the cable completely. Also refer to the table below.
ENGLISH We recommend to use professional accessories only. • Clean and grease the bit shank. • Insert the bit shank into the tool holder (6). • Push the bit down and turn it slightly until it fits into the slots. • Pull on the bit to check if it is properly locked. The hammering function requires the bit to be able to move axially several centimetres when locked in the tool holder. • To remove a bit pull back the tool holder locking sleeve (12) and pull out the bit. Fitting the side handle (fig.
ENGLISH Be aware of the location of pipework and wiring. Apply only a gentle pressure to the tool (approx. 5 kg). Excessive force does not speed up drilling but decreases tool performance and may shorten tool life. Do not drill or drive too deep to prevent damage to the dust cover. Always hold the tool firmly with both hands and ensure a secure stance (fig. H). Always operate the tool with the side handle properly mounted. Switching on and off (fig.
ENGLISH • Insert the appropriate screwdriver bit. When driving slotted head screws always use bits with a finder sleeve. • Gently press the variable speed switch (1) to prevent damage to the screw head. In reverse (LH) rotation the tool speed is automatically reduced for easy screw removal. • When the screw is flush with the workpiece, release the variable speed switch to prevent the screw head from penetrating into the workpiece. D25113K/D25114K/D25213K - Chipping and chiselling (fig.
