www. .
3 1 4 A 2 5 Copyright DEWALT
4 7 9 6 10 11 8 C1 B 14 14 12 12 10 11 10 A 13 14 11 12 10 11 3 B C2 C3 3
17 15 5 15 16 17 5 D2 D1 19 18 E1 4 E2
ENGLISH ANGLE GRINDER D28410/D28411/D28413/D28414/D28420/ D28421/D28422/D28423/D28432C/D28750 Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical data Voltage (U.K. & Ireland only) Power input No-load speed Wheel diameter Spindle Weight V V W min-1 mm Voltage (U.K.
ENGLISH Level of sound pressure according to 86/188/EEC & 98/37/EC, measured according to EN 50144: D28410 D28411 D28413 D28414 D28420 D28421 D28422 D28423 D28432C D28750 LpA (sound pressure) dB(A)* 90.5 90.0 90.0 90.0 90.5 90.5 90.0 90.0 90.0 90.5 LWA (acoustic power) dB(A) 99.5 98.5 98.5 98.5 99.5 99.5 99.0 98.5 98.5 99.0 * at the operator’s ear Take appropriate measures for the protection of hearing.
ENGLISH 11 Remove adjusting keys and wrenches Always check that adjusting keys and wrenches are removed from the tool before operating the tool. 12 Extension cables Before use, inspect the extension cable and replace if damaged. When using the tool outdoors, only use extension cables intended for outdoor use and marked accordingly. 13 Use appropriate tool The intended use is described in this instruction manual. Do not force small tools or attachments to do the job of a heavy-duty tool.
ENGLISH • Ensure that the grinding or cutting disc is mounted correctly before use. • Let the tool run at no-load in a safe position for at least 30 seconds. If there is a considerable vibration or if any other defect occurs, stop the tool and check it to determine the cause. • Do not operate this tool without the guard in place. • Check that the workpiece is properly supported. • Do not operate the tool near flammable liquids, gases or dust.
ENGLISH • Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws. Also refer to the following table. Conductor size (mm2) 0.75 1.00 1.50 2.50 4.00 Voltage 115 Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth pin marked E or . Fitting a mains plug to 115 V units (U.K.
ENGLISH • Fit the inner flange (10) correctly onto the spindle (11) (fig. C1). • Place the disc (12) on the flange (10) (fig. C2). When fitting a disc with a raised center, make sure that the raised centre (13) is facing the flange (10). • Screw the outer flange (14) onto the spindle (11) (fig. C3): - the ring on the flange (14) must face towards the disc when fitting a grinding disc (A); - the ring on the flange (14) must face away from the disc when fitting a cutting disc (B).
ENGLISH Maintenance Your DEWALT Power Tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Lubrication Your power tool requires no additional lubrication. You can check the location of your nearest authorised repair agent by contacting your local DEWALT office at the address indicated in this manual.
Belgique et Luxembourg België en Luxemburg DEWALT Mechelen Campus, Schaliënhoevedreef 20E B-2800 Mechelen Tel: +32 (0)015 - 15 47 9211 Fax: +32 (0)015 - 15 47 9210 www.dewalt.com Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70 20 15 10 Fax: 36 94 49 01 www.dewalt-nordic.com Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Hellas) S.A.
