Instruction manual

TROUBLESHOOTING GUIDE
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
CONTACT A D
EWALT SERVICE CENTER OR CALL 1800-654-155.
DISCONNECT BATTERY PACK FROM TOOL BEFORE ALL REPAIRS
SYMPTOM CAUSE FIX
Tool doesn’t turn on Low battery charge or damaged battery Charge or replace battery
(Headlights don’t turn on) Terminals are dirty or damaged See authorized service center
Contact trip lock is in a locked position Unlock contact trip lock
Bent contact trip See authorized service center
Tool internal electronics not reset Remove battery, wait 3 seconds and reinsert
Damaged internal electronics See authorized service center
Tool doesn’t actuate Motor stops running after 2 seconds Normal operation; release trigger or contact trip and redepress
(Headlights on, motor does not run) Contact trip or trigger not depressed See instruction manual
Damaged trigger See authorized service center
Bent contact trip See authorized service center
Contact trip lock in the locked position Unlock contact trip lock
(Sequential mode only)
Damaged internal electronics See authorized service center
Tool doesn’t actuate (Headlights flash 4 times) Low battery charge or damaged battery Charge or replace battery
Tool doesn't actuate Jammed fastener Remove the battery, clear the jammed fastener, (push driver blade
back up manually if necessary) and reinsert battery pack
Jammed mechanism See authorized service center
Tool doesn’t actuate (Headlights on, motor runs) Damaged internal electronics See authorized service center
Tool doesn’t actuate Damaged return system Replace return system; see authorized service center
(Headlights on, motor runs, driver blade stuck down) Debris in nosepiece Clean nosepiece
Damaged driver/return assembly Replace driver/return assembly; see authorized service center
Tool operates, but does not drive the fastener fully Low battery charge or damaged battery Charge or replace battery
Depth adjustment set too shallow Rotate depth adjustment wheel to a deeper setting
Tool not firmly applied to workpiece See instruction manual
Material and fastener length Choose appropriate material or fastener length
too rigorous an application
Damaged or worn driver blade tip Replace driver/return assembly; see authorized service center
Damaged or worn driver/return assembly Replace driver/return assembly; see authorized service center
Tool operates, but no fastener driven No fasteners in magazine Load fasteners into magazine
Wrong size or angle fasteners Use only recommended fasteners
Debris in nosepiece Clean nosepiece
Debris in magazine Clean magazine
Worn magazine Replace magazine; see authorized service center
Damaged or worn driver blade Replace driver/return assembly; see authorized service center
Damaged pusher spring Replace spring; see authorized service center
Jammed fastener Wrong size or angle fasteners Use only recommended fasteners
Damaged or worn driver blade Replace driver/return assembly; see authorized service center
Material and fastener length Material or fastener length inappropriate
too rigorous an application
Low battery charge or damaged battery Charge or replace battery
Debris in nosepiece Clean nosepiece
Debris in magazine Clean magazine
Worn magazine Replace magazine; see authorized service center
Worn or damaged pusher spring Replace spring; see authorized service center
DEWALT Battery and Charger Systems
Battery Output Chargers/Charge Time
Nominal 240 Volts 12 Volts
X Indicates that the battery pack is not compatible with that specific charger.
All charge times are approximate. Actual charge time may vary.
Read the instruction manual for more specific information.
The battery voltage is nominal, it can measure above or below depending on the state of charge.
Cat. Number Voltage Amp Hour 97014 98014 DW9106 DW9107 DW9108 DW9115 DW9116 DW9117 DW9118 DE9116 DE9118 DW911 DC011 DW0245 DE2046 DW9109
DW0242 24 2.0 X X X X X X X X X X X X X 60 60 X
DE0240-XJ 24 2.0 X X X X X X X X X X X X X 60 60 X
DW0240 24 1.7 X X X X X X X X X X X X X 60 60 X
DW9096 18 2.4 X X X X 60 X 60 20 X 60 X 60 60 X X 60
DE9095-XJ 18 2.0 X X X X 60 X 60 20 X 60 X 60 60 X X 60
DE9091-XJ 14.4 2.0 45 45 45 45 45 15 45 15 90 45 90 45 45 X X 45
DW9091 14.4 1.7 45 45 45 45 45 15 45 15 90 45 90 45 45 X X 45
DC9071 12 2.4 60 60 60 60 60 15 60 15 60 60 60 60 60 X X 60
DE9074-XJ 12 1.25 45 45 45 30 30 15 30 12 60 30 60 30 30 X X 30
DW9072 12 1.2 45 45 45 30 30 15 30 12 60 30 60 30 30 X X 30
DE9071-XJ 12 2.0 60 60 60 45 45 15 45 15 90 45 90 45 45 X X 45
DW9071 12 1.7 60 60 60 45 45 15 45 15 90 45 90 45 45 X X 45
DW9050 12 1.3 40 40 40 X X 15 X X X X X X X X X X
DW9063 9.6 1.25 45 45 45 30 30 15 30 12 60 30 60 30 30 X X 30
DW9062 9.6 1.3 45 45 45 30 30 15 30 12 60 30 60 30 30 X X 30
DW9061 9.6 1.7 60 60 60 45 45 15 45 15 90 45 90 45 45 X X 45
DW9048 9.6 1.3 40 40 40 X X 15 X X X X X X X X X X
DW9057 7.2 1.25 45 45 45 30 30 15 30 12 60 30 60 30 30 X X 30
DW9046 7.2 1.3 40 40 40 X X 15 X X X X X X X X X X
DC9096 18 2.4 X X X X 60 X 60 20 X 60 X 60 60 X X 60
DC9091 14.4 2.4 60 60 60 60 60 15 60 15 60 60 60 60 60 X X 60
Angled Straight
Nail Lengths 1-1/4'', 1-1/2", 1-3/4", 2", 2-1/2" 1-1/4'', 1-1/2", 1-3/4", 2", 2-1/2"
(32mm, 38mm, 44mm, 51mm, 65mm) (32mm, 38mm, 44mm, 51mm, 65mm)
Shank Diameters 16 gauge 16 gauge
Nail Stick Angles 20˚ 0˚
TOOL SPECIFICATIONS
NAIL SPECIFICATIONS
DC613 DC615 DC617 DC618 DC619
Firing Mode Sequential Sequential Sequential Selective Sequential
Voltage Multi (14.4 & 12) Multi (14.4 & 12) 18 18 18
Height 12'' (305mm) 12.4'' (315mm) 12'' (305mm) 12.4'' (315mm) 12.4'' (315mm)
Width 4.18'' (106mm) 4.18'' (106mm) 4.18'' (106mm) 4.18'' (106mm) 4.18'' (106mm)
Length 12.75'' (324mm) 12.5'' (317mm) 12.75'' (324mm) 12.5'' (317mm) 12.5'' (317mm)
Weight 7.8lbs. (3.57kg) 7.8lbs. (3.57kg) 8.5lbs. (3.8kg) 8.5lbs (3.8kg) 8.5lbs. (3.8kg)
Magazine Angle Straight Angled 20˚ Straight Angled 20˚ Angled 20˚
Loading Capacity Up to 110 Nails Up to 120 Nails Up to 110 Nails Up to 120 Nails Up to 120 Nails