DC740 DC750 1
Dansk 6 Deutsch 13 English 21 Español 29 Français 37 Italiano 45 Nederlands 53 Norsk 61 Português 68 Suomi 76 Svenska 83 Türkçe 90 EÏÏËÓÈο 99 Copyright DEWALT 2
4 5 6 7 2 1 8 9 9 12 10 10 11 11 9 12 A 3
13 9 13 9 B 5 14 C 4 15 D
2 6 E F 5
DANSK OPLADELIG SLAGBOREMASKINE/ SKRUETRÆKKER DC740/DC750 Tillykke! Følgende piktogrammer anvendes i denne håndbog: Du har valgt et DEWALT værktøj. Mange års erfaring, ihærdig produktudvikling og innovation gør DEWALT til en af de mest pålidelige partnere for professionelle brugere. Angiver risiko for personskade, livsfare eller ødelæggelse af værktøjet, hvis brugervejledningens instruktioner ikke følges. Tekniske data DC740 DC750 12 9,6 Spænding V Omdrejningstal ubelastet 1. gear min-1 2.
DANSK Produktudviklingsdirektør Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Tyskland d Undgå at ødelægge ledningen. Undgå at bære, trække eller afbryde el-værktøjet ved at rykke i ledningen. Beskyt ledningen mod varme, olie, skarpe kanter eller maskindele, der er i bevægelse. Beskadigede eller indviklede ledninger øger risikoen for elektrisk stød. e Hvis el-værktøj benyttes i det fri, skal der benyttes en forlængerledning, som er godkendt til udendørs brug.
DANSK 4 Brug og vedligeholdelse af el-værktøj a Undgå at overbelaste el-værktøjet. Brug altid det rette el-værktøj til opgaven. Med det rigtige el-værktøj udføres arbejdet lettere og sikrere inden for det angivne effektområde. b Brug ikke el-værktøjet, hvis afbryderen er defekt. El-værktøj, der ikke kan kontrolleres med afbryderen, er farligt og skal repareres. c Træk stikket ud af stikkontakten inden indstilling, tilbehørsudskiftning eller opbevaring af el-værktøjet.
DANSK Rør dem ikke med strømledende materialer Oplad ikke et beskadiget batteri Læs brugsanvisningen før laderen tages i brug Må kun anvendes til opladning af DEWALT-batterier; andre batterier kan revne og forårsage skader Må ikke udsættes for væske En beskadiget ledning bør omgående udskiftes +40 ˚c +4 ˚c Temperatur for opladning +4 °C til +40 °C Følg givne anbefalinger med hensyn til at skille sig af med batteriet 1 2 3 4 5 6 7 8 9 Afbryder med variabel hastighedskontrol Omskifter for højre/venstregang
DANSK Batteri (fig. A & B) Opladning af batteriet (fig. A) Når batteriet skal oplades for første gang eller efter længere tids opbevaring, kan det kun oplades 80%. Efter flere opladninger og afladninger vil batteriet nå op på fuld kapacitet. Kontroller altid lysnettets strøm, før batteriet oplades. Hvis lysnettet er i orden, men batteriet ikke oplades, skal laderen indleveres hos en autoriseret DEWALT forhandler. Under opladningen kan laderen og batteriet blive varme.
DANSK Pas på du ikke borer ind i rør og ledninger. Anvend kun et let tryk på værktøjet. Stort tryk øger ikke borehastigheden, men nedsætter værktøjets ydeevne og evt. også levetiden. For at minimere blokering ved gennembrydning, bør presset med boret gradvist reduceres ved slutningen af boringen. Lad motoren gå, mens boret trækkes ud af et boret hul. Dette hjælper med til at forhindre at boret sætter sig fast. Før værktøjet tages i brug: • Sørg for at batteriet er (helt) opladet. • Indsæt det ønskede bor.
DANSK Separat indsamling af brugte produkter og emballage gør det muligt at genbruge materialerne. Genbrug af materialer forebygger miljøforurening og nedbringer behovet for råstoffer. På grund af forskning og udvikling kan ovenstående specifikationer ændres, hvilket ikke meddeles separat. GARANTI • 30 DAGE TILFREDS-KUNDE GARANTI • Lokale regler kan give mulighed for separat indsamling af elektriske husholdningsprodukter på kommunale lossepladser eller hos en forhandler, når du køber et nyt produkt.
DEUTSCH AKKU-BOHRSCHRAUBER DC740/DC750 Herzlichen Glückwunsch! Sie haben sich für ein Werkzeug von DEWALT entschieden, das die lange DEWALT-Tradition fortsetzt, nur ausgereifte und in zahlreichen Tests bewährte Qualitätsprodukte für den Fachmann anzubieten. Lange Jahre der Erfahrung und kontinuierliche Weiterentwicklung machen DEWALT zu Recht zu einem verläßlichen Partner aller professionellen Anwender.
DEUTSCH Direktor Produktentwicklung Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Deutschland Allgemeine Sicherheitsregeln Achtung! Sämtliche Anweisungen sind zu lesen. Die Nichteinhaltung der nachstehend aufgeführten Anweisungen kann elektrischen Schlag, Brand und/oder schwere Verletzungen verursachen. Der nachfolgend verwendete Begriff „Werkzeug“ bezieht sich auf netzbetriebene Werkzeuge (mit Netzkabel) und auf akkubetriebene Werkzeuge (ohne Netzkabel).
DEUTSCH f Tragen Sie geeignete Kleidung. Tragen Sie keine weite Kleidung oder Schmuck. Halten Sie Haare, Kleidung und Handschuhe fern von sich bewegenden Teilen. Lockere Kleidung, Schmuck oder lange Haare können von sich bewegenden Teilen erfasst werden. g Falls Staubabsaug- und -fangvorrichtungen vorhanden sind, vergewissern Sie sich, daß diese angeschlossen sind und richtig verwendet werden. Das Verwenden dieser Einrichtungen verringert Gefährdungen durch Staub.
DEUTSCH +40 ˚c Zusätzliche Sicherheitshinweise für Akkus +4 ˚c Feuergefahr! Vermeiden Sie ein Kurzschließen der Kontakte eines abgenommenen Akkus. Lagern bzw. transportieren Sie den Akku nie ohne die mitgelieferte Schutzkappe über den Kontakten. • Die Akkuflüssigkeit, eine 25 bis 30% starke Kaliumhydroxidlösung, kann schädlich sein. Falls die Lösung mit der Haut in Berührung kommt, spülen Sie sofort mit reichlich Wasser. Neutralisieren Sie die Lösung mit einer milden Säure wie Zitronensaft oder Essig.
DEUTSCH Ihr Ladegerät DE9116 kann DEWALT NiMH- und NiCd-Akkus im Bereich von 7,2 bis 18 V laden. 9 Akku 10 Löseknöpfe 11 Ladegerät 12 Ladekontrolleuchte (rot) Elektrische Sicherheit Das Ladegerät wurde nur für eine Spannung konzipiert. Überprüfen Sie deswegen, ob die Netzspannung der auf dem Typenschild des Ladegerätes angegebenen Spannung entspricht. Ihr DEWALT-Ladegerät ist gemäß EN 60745 zweifach isoliert; eine Erdleitung ist aus diesem Grunde überflüssig.
DEUTSCH • Nehmen Sie die Schutzkappe (13) ab, bevor Sie den Akku (9) in das Ladegerät bzw. Werkzeug einsetzen. • Setzen Sie die Schutzkappe unmittelbar nach Entfernen des Akkus vom Ladegerät bzw. Werkzeug über die Kontakte. Vergewissern Sie sich, daß sich die Schutzkappe in ihrer Lage befindet, bevor Sie einen abgenommenen Akku lagern oder transportieren. Einsetzen und Entfernen von Bits (Abb.
Ein- und Ausschalten (Abb. A & D) • Betätigen Sie zum Starten des Elektrowerkzeuges den Drehzahl-Regelschalter (1). Je tiefer der Drehzahl-Regelschalter gedrückt wird, um so höher ist die Drehzahl des Antriebsmotors. • Lassen Sie zum Stoppen des Werkzeuges den Schalter los. • Um das Werkzeug in der Aus-Stellung zu arretieren, schieben Sie den Rechts-/Linkslaufschalter (2) in die Mittelstellung.
DEWALT nimmt Ihre ausgedienten DEWALT-Produkte gern zurück und sorgt für eine umweltfreundliche Entsorgung und Wiederverwertung. Um diesen Dienst zu nutzen, bitte schicken Sie Ihr Produkt zu einer Vertragswerkstatt. Hier wird es dann auf unsere Kosten gesammelt. Die Adresse des zuständigen Büros von DEWALT steht in dieser Anleitung, darüber läßt sich die nächstgelegene Vertragswerkstatt ermitteln.
ENGLISH CORDLESS DRILL/DRIVER DC740/DC750 Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. The following symbols are used throughout this manual: Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions in this manual. Technical data DC740 DC750 12 9.
ENGLISH Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11 D-65510, Idstein, Germany General safety rules Warning! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term „power tool“ in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. SAVE THESE INSTRUCTIONS.
ENGLISH 4 Power tool use and care a Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools.
ENGLISH Description (fig. A) Do not probe with conductive objects Do not charge damaged battery packs Read instruction manual before use Use only with DEWALT battery packs, others may burst, causing personal injury and damage Your cordless drill/driver DC740/DC750 has been designed for professional drilling and screwdriving applications.
ENGLISH • The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug (see below). Brown is for Live (L) (2) and Blue is for Neutral (N) (4). • Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws. Never use a light socket.
ENGLISH • Place the bit in the chuck as far as it will go and lift slightly before tightening. • Tighten firmly by turning the sleeve clockwise. • To remove the bit, proceed in reverse order. Selecting the operating mode or adjusting the torque (fig. D) The collar of this tool has 15 positions for the adjustment of the torque to suit the size of the screw and the workpiece material. For torque adjustment, refer to the section „Screwdriving“.
ENGLISH Drilling in wood • Holes in wood can be made with the same twist drills used for metal. These bits may overheat unless pulled out frequently to clear chips from the flutes. • For larger holes use Auger bits. • Use a block of wood to back up workpieces that may splinter. Consult your dealer for further information on the appropriate accessories. Maintenance Your DEWALT power tool has been designed to operate over a long period of time with a minimum of maintenance.
ENGLISH GUARANTEE • 30 DAY NO RISK SATISFACTION GUARANTEE • If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete as purchased, to the point of purchase, for a full refund or exchange. Proof of purchase must be produced. • ONE YEAR FREE SERVICE CONTRACT • If you need maintenance or service for your DEWALT tool, in the 12 months following purchase, it will be undertaken free of charge at an authorized DEWALT repair agent.
ESPAÑOL TALADRO/ATORNILLADOR SIN CABLE DC740/DC750 ¡Enhorabuena! Usted ha optado por una herramienta DEWALT. Muchos años de experiencia y una gran asiduidad en el desarrollo y la innovación de sus productos han convertido DEWALT en un socio muy fiable para el usuario profesional. En el presente manual figuran los pictogramas siguientes: Indica peligro de lesiones, de accidentes mortales o de averías en la herramienta en caso de no respeto de las instrucciones en este manual.
ESPAÑOL Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Alemania Normas de seguridad generales ¡Atención! Lea íntegramente estas instrucciones. En caso de no atenerse a las instrucciones de seguridad siguientes, ello puede dar lugar a una descarga eléctrica, incendio o lesión grave.
ESPAÑOL d Retire las herramientas de ajuste o llaves fijas antes de conectar la herramienta eléctrica. Una herramienta o llave colocada en una pieza giratoria puede producir lesiones al ponerse a funcionar. e Sea precavido. Evite adoptar una posición que fatigue su cuerpo; mantenga un apoyo firme sobre el suelo y conserve el equilibrio en todo momento. Ello le permitirá controlar mejor la herramienta eléctrica en caso de presentarse una situación inesperada.
ESPAÑOL Normas de seguridad adicionales para baterías ¡Peligro de incendio! Evite que el metal cortocircuite los contactos del paquete de baterías desmontable. No guarde o transporte el paquete de baterías sin su tapa protectora colocada sobre los contactos. Una vez terminada la vida técnica de la batería, elimínela sin dañar el medio ambiente No arroje la batería al fuego Verificación del contenido del embalaje • El líquido una solución de un 25-30% de hidróxido de potasio, puede resultar nocivo.
ESPAÑOL 9 Batería 10 Pulsadores de arranque 11 Cargador 12 Indicador de carga (rojo) Seguridad eléctrica El cargador ha sido diseñado para un solo voltaje. Compruebe siempre que el voltaje de la red corresponde al valor indicado en la placa de características. Su cargador DEWALT tiene doble aislamiento, conforme a la norma EN 60745; por consiguiente, no se requiere conexión a tierra.
ESPAÑOL Asegúrese de que la tapa protectora está en su sitio antes de guardar o transportar un paquete de baterías desmontable. Inserción y extracción de puntas (fig. A & C) • Abra el portabrocas girando el manguito (14) hacia la izquierda e inserte la parte lisa de la broca. • Inserte la punta hasta el fondo en el portabrocas y, antes de apretar, levántela levemente. • Apriete bien, girando el manguito hacia la derecha. • Para sacar la broca, siga el mismo procedimiento en orden inverso.
ESPAÑOL Atornillado (fig. A) • Seleccione el giro hacia la derecha o hacia la izquierda utilizando el mando deslizante (2). • Sitúe el collarín (4) en la posición 1 y comience a atornillar (par bajo). • Si el embrague actúa demasiado pronto, ajuste el collarín para aumentar el par según sea necesario. Perforación (fig. A) • Seleccione el modo de perforación utilizando el collarín (4). Taladro en metal • Utilice un lubricante para corte cuando taladre metal.
ESPAÑOL GARANTÍA Batería recargable Esta batería de larga duración se debe recargar cuando no tenga la potencia suficiente en trabajos que realizaba fácilmente con anterioridad. Una vez terminada su vida técnica, elimínela sin dañar el medio ambiente: • Agote la batería por completo y, a continuación, sáquela de la herramienta. • Las células NiCd y NiMH son reciclables. Llévelas a su distribuidor o a un centro de reciclaje local. Las baterías recogidas se reciclarán o se desecharán adecuadamente.
FRANÇAIS VISSEUSE-PERCEUSE A PERCUSSION SANS FIL DC740/DC750 Félicitations ! Vous avez choisi un outil DEWALT. Depuis de nombreuses années, DEWALT produit des outils électriques adaptés aux exigences des utilisateurs professionnels. Les symboles suivants sont utilisés dans le présent manuel : En cas de non-respect des instructions dans le présent manuel, il y a risque de blessure, danger de mort ou possibilité de dégradation de l’outil.
FRANÇAIS Directeur de développement produits Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Allemagne Consignes générales de sécurité Attention ! Lisez toutes les instructions. Le nonrespect des instructions indiquées ci-dessous peut entraîner une électrocution, un incendie et/ou de graves blessures.
FRANÇAIS e Ne surestimez pas vos capacités. Évitez d’adopter une position fatigante pour le corps ; veillez à ce que votre appui au sol soit ferme et conservez l’équilibre à tout moment. Vous contrôlerez mieux l’outil dans des situations inattendues. f Portez des vêtements appropriés. Ne portez pas de vêtements amples ni de bijoux. N’approchez pas les cheveux, vêtements ou gants des parties de l’appareil en rotation.
FRANÇAIS 6 Réparations a Ne faites réparer votre outil électroportatif que par du personnel qualifié et seulement avec des pièces de rechange d’origine. Cela garantira le maintien de la sécurité de votre outil. Ne pas exposer à l’eau Remplacer immédiatement +40 ˚c +4 ˚c Directives de sécurité additionnelles pour packbatteries Danger d’incendie ! Éviter de courtcircuiter les contacts d’un pack de batterie non fixé avec du métal.
FRANÇAIS Chargeur Votre chargeur DE9107 accepte des packsbatteries NiCd DEWALT de 7,2 à 14,4 V. Votre chargeur DE9108/DE9118 accepte des packs-batteries NiCd DEWALT de 7,2 à 18 V. Votre chargeur DE9116 accepte des packsbatteries NiCd et NiMH DEWALT de 7,2 à 18 V. 9 Pack-batteries 10 Boutons de dégagement 11 Chargeur 12 Voyant rouge Assemblage et réglage Sécurité électrique Pack-batteries (fig. A & B) Le moteur électrique a été conçu pour une seule tension.
FRANÇAIS Couvercle des batteries (fig. B) Un couvercle permet de couvrir les contacts d’un pack de batteries non fixé. Si le couvercle n’est pas en place, un objet métallique pourrait provoquer un court-circuit dans les contacts, entraîner un risque d’incendie et endommager le pack de batteries. • Enlevez le couvercle de protection (13) avant de mettre le pack de batteries en place (9) dans le chargeur ou l’outil.
FRANÇAIS Mise en marche et arrêt (fig. A & D) • Pour mettre l’outil en marche, appuyer sur l’interrupteur à variateur (1). La vitesse augmente avec la pression exercée sur l’interrupteur. • Pour arrêter l’outil, relâcher l’interrupteur. • Pour bloquer l’outil en position arrêt, mettez le sélecteur de rotation gauche/droite (2) en position médiane. L’outil est équipé d’un frein qui arrête le mandrin dès que l’interrupteur à variateur est complètement relâché. Vissage (fig.
FRANÇAIS Pour connaître l’adresse du réparateur agréé le plus proche de chez vous, contactez le bureau DEWALT à l’adresse indiquée dans ce manuel. Vous pourrez aussi trouver une liste des réparateurs agréés de DEWALT et de plus amples détails sur notre service après-vente sur le site Internet à l’adresse suivante : www.2helpU.com. Packs-batteries rechargeables Les packs-batteries doivent être rechargés dès qu’ils ne fournissent plus suffisamment d’énergie pour des travaux réalisés aisément auparavant.
ITALIANO AVVITATORE/TRAPANO A PERCUSSIONE A BATTERIA DC740/DC750 Congratulazioni! I seguenti simboli vengono usati nel presente manuale: Siete entrati in possesso di un utensile DEWALT. Anni di esperienza, continui miglioramenti ed innovazioni tecnologiche fanno dei prodotti DEWALT uno degli strumenti più affidabili per l’utilizzatore professionale. Indica rischio di infortunio, pericolo di morte o danno all’apparecchio qualora non ci si attenga alle istruzioni contenute nel presente manuale.
ITALIANO Direttore ricerca e sviluppo Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Germania d Non esporre il cavo a sollecitazioni. Non usare il cavo per trasportare o trainare l’utensile e non tirarlo per estrarre la spina dalla presa di corrente. Mantenere il cavo al riparo dal calore, da bordi taglienti e/o da parti in moto. I cavi danneggiati o aggrovigliati aumentano il rischio di scosse elettriche.
ITALIANO g Se gli utensili sono provvisti di attacchi per la connessione di dispositivi di aspirazione o raccolta della polvere, assicurarsi questi siano installati e utilizzati correttamente. L’impiego dei suddetti dispositivi diminuisce i rischi correlati alle polveri. 4 Uso e cura degli elettroutensili a Non sovraccaricare l’utensile. Usare l’elettroutensile adatto per il lavoro da eseguire.
ITALIANO • Non cercare mai, per alcun motivo, di aprire il gruppo batterie. Etichette sul caricabatterie e sul gruppo batterie I seguenti simboli sono indicati nelle etichette sul caricabatterie e sul gruppo batterie: 100% Batteria sotto carica 100% Batteria carica Batteria difettosa Non toccate con oggetti conduttori Non caricate batterie danneggiate; sostituitele immediatamente Leggete il manuale di istruzioni prima di mettere in funzione Usate solamente batterie DEWALT.
ITALIANO CH CH Per la sostituzione del cavo di alimentazione, utilizzare sempre la spina di tipo prescritto. Tipo 11 per la classe II (doppio isolamento) utensili elettrici Tipo 12 per la classe I (messa a terra) utensili elettrici Gli apparecchi portatili, utilizzati in ambiente esterno, devono essere collegati ad un interruttore differenziale.
ITALIANO Inserimento e rimozione della punta (figg. A & C) • Aprire il mandrino ruotando il manicotto (14) in senso antiorario e infilare lo stelo della punta. • Inserire fino a battuta la punta nel mandrino e tenerla sollevata leggermente mentre si serra in posizione. • Serrare fermamente ruotando il manicotto in senso orario. • Per togliere la punta procedere in ordine inverso. Selezione del modo operativo o regolazione della coppia (fig.
ITALIANO Avvitatura (fig. A) • Selezionare la rotazione in avanti o all’indietro mediante il comando avanti/indietro (2). • Regolare il collare (4) sulla posizione 1 e cominciare ad avvitare (a bassa coppia). • Se la frizione comincia a slittare troppo presto, intervenire sulla bussola per aumentare di quanto necessario il valore di coppia. Foratura (fig. A) • Selezionare sul collare di regolazione (4) il modo operativo di rotazione.
ITALIANO GARANZIA Gruppo batterie ricaricabile Ricaricare il gruppo batterie di lunga durata quando la potenza erogata risulta insufficiente all’esecuzione di lavori effettuati senza alcuna difficoltà in precedenza. Al termine della durata utile, scartarlo con le dovute precauzioni per l’ambiente: • Esaurire completamente la potenza del gruppo batterie, quindi estrarlo dall’utensile. • Le batterie NiCd/NiMH sono ricaricabili.
NEDERLANDS SNOERLOZE SCHROEF-/ KLOPBOORMACHINE DC740/DC750 Gefeliciteerd! U heeft gekozen voor een machine van DEWALT. Jarenlange ervaring, voortdurende produktontwikkeling en innovatie maken DEWALT tot een betrouwbare partner voor de professionele gebruiker. In deze handleiding worden de volgende pictogrammen gebruikt: Duidt op mogelijk lichamelijk letsel, levensgevaar of kans op beschadiging van de machine indien de instructies in deze handleiding worden genegeerd.
NEDERLANDS Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Duitsland Algemene veiligheidsvoorschriften Waarschuwing! Lees alle voorschriften. Wanneer de volgende voorschriften niet in acht worden genomen, kan dit een elektrische schok, brand of ernstig letsel tot gevolg hebben.
NEDERLANDS Een instelgereedschap of sleutel in een draaiend deel van het gereedschap kan tot verwondingen leiden. e Reik niet te ver. Zorg er altijd voor dat u stevig staat en in evenwicht blijft. Daardoor kunt u het gereedschap in onverwachte situaties beter onder controle houden. f Draag geschikte kleding. Draag geen loshangende kleding of sieraden. Houd haren, kleding en handschoenen uit de buurt van bewegende delen.
NEDERLANDS 6 Service a Laat het gereedschap alleen repareren door gekwalificeerd en vakkundig personeel en alleen met originele vervangingsonderdelen. Daarmee wordt gewaarborgd dat de veiligheid van het gereedschap in stand blijft. Niet aan water blootstellen Beschadigd snoer direct laten vervangen +40 ˚c +4 ˚c Alleen laden bij temperaturen tussen 4 °C en 40 °C Extra veiligheidsrichtlijnen voor accu’s Brandgevaar! Voorkom kortsluiting tussen de contactpunten van een losse accu.
NEDERLANDS Oplader Uw DE9107 oplader is geschikt voor DeWALT NiCdaccu’s van 7,2 tot 14,4 V. Uw DE9108/DE9118 oplader is geschikt voor DeWALT NiCd-accu’s van 7,2 tot 18 V. Uw DE9116 oplader is geschikt voor DeWALT NiCden NiMH-accu’s van 7,2 tot 18 V. 9 Accu 10 Accu-vergrendelingsknoppen 11 Oplader 12 Oplaadindicatie (rood) Elektrische veiligheid De elektrische motor is ontwikkeld voor een bepaalde spanning. Controleer altijd of de accuspanning overeenkomt met de waarde op het typeplaatje.
NEDERLANDS Zorg dat de afdekdop op zijn plaats zit voodat u een losse accu opbergt of transporteert. Plaatsen en verwijderen van een boortje of schroevendraaierbit (fig. A & C) • Open de boorhouder door de kraag (14) linksom te draaien en plaats het boortje of de schroevedraaierbit. • Plaats het boortje of de schroevedraaierbit zo ver mogelijk in de boorhouder. Trek het boortje of de bit daarna iets terug. • Klem het boortje of de bit stevig vast door de kraag rechtsom te draaien.
NEDERLANDS • Schuif de L/R-schakelaar (2) in de middenstand om de machine in de uit-stand te blokkeren. De machine is uitgerust met een mechanisme waardoor de boorkop wordt afgeremd zodra de schakelaar voor elektronisch toerental geheel wordt losgelaten. In- en uitdraaien van schroeven (fig. A) • Selecteer de gewenste draairichting met de L/Rschakelaar (2). • Zet de instelring (4) in pos. 1 (laag koppel) en draai de schroef in het werkstuk.
NEDERLANDS GARANTIE • 30 DAGEN “NIET GOED, GELD TERUG” Oplaadbare accu De duurzame accu moet worden opgeladen, zodra deze niet meer genoeg energie levert voor werkzaamheden die daarvóór nog moeiteloos konden worden verricht. Versleten accu’s dienen op milieubewuste wijze te worden verwijderd: • Gebruik de energie van de accu helemaal op en verwijder dan de accu uit de machine. • NiCd- en NiMH-accu’s zijn recycleerbaar.
NORSK OPPLADBAR SLAGBOREMASKIN/ SKRUTREKKER DC740/DC750 Gratulerer! Du har valgt et DEWALT verktøy. Årelang erfaring, konstant produktutvikling og fornyelse gjør DEWALT til en av de mest pålitelige partnere for profesjonelle brukere. Følgende symboler brukes i denne instruksjonsboken: Betegner risiko for personskade, livsfare eller ødeleggelse av verktøyet dersom instruksene i denne instruksjonsboken ikke følges. Tekniske data Spenning Turtall, ubelastet 1. gear 2.
NORSK Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Tyskland Generelle sikkerhetsforskrifter Advarsel! Les gjennom alle anvisningene. Hvis anvisningene nedenfor ikke overholdes, kan det medføre elektrisk støt, brann og/eller alvorlige skader. Uttrykket «elektroverktøy» i alle advarslene nedenfor gjelder for strømdrevne elektroverktøy (med ledning) og batteridrevne elektroverktøy (uten ledning). TA GODT VARE PÅ DISSE ANVISNINGENE.
NORSK 4 Aktsom håndtering og bruk av elektroverktøy a Ikke bruk makt på elektroverktøyet. Bruk et elektroverktøy som er beregnet på den type arbeid du vil utføre. Med et passende elektroverktøy arbeider du bedre og sikrere i det angitte effektområdet. b Ikke bruk elektroverktøy med defekt på-/ avbryter. Et elektroverktøy som ikke lenger kan slås av eller på med bryteren, er farlig og må repareres.
NORSK Beskrivelse (fig. A) Ikke berør dem med ledende gjenstander Sett ikke skadde batteripakker inn i laderen Les bruksanvisningen før laderen tas i bruk Må bare anvendes for lading av DEWALT batterier; andre batteripakker kan revne og forårsake skader Din oppladbare oppladbar boremaskin/skrutrekker DC740/DC750 er utformet for profesjonell boring og skrutrekking.
NORSK Batteripakke (fig. A & B) Lading av batteripakken (fig. A) Når du lader batteripakken for første gang, eller etter en langvarig oppbevaring, kan den bare ta imot 80% opplading. Etter flere oppladninger og utladninger, vil batteripakken oppnå full kapasitet. Kontroller alltid nettet før du lader batteripakken. Hvis det er strøm på nettet, men batteripakken ikke blir oppladet, må du bringe laderen til et DEWALTautorisert serviceverksted. Under oppladningen kan batteripakken kjennes varm ved berøring.
NORSK Trykk bare lett på maskinen. Stor kraft fører ikke til raskere boring, men til at maskinen presterer dårligere og at levetiden eventuelt reduseres. For å begrense fastsitting etter gjennombruddet til et minimum, reduseres trykket på borspissen stadig mer mot slutten av boringen. La motoren fortsette å gå mens bitsen trekkes ut av borehullet. Dette forhendrer at den setter seg fast. Boring i tre • Det kan bores i tre med samme spiralbor som for metall eller spesielle trebor.
NORSK Lokale regelverk kan legge tilrette for kildesortering av elektriske produkter fra husholdningen, ved kommunale deponier eller gjennom forhandleren når du kjøper et nytt produkt. DEWALT har tilrettelagt for innsamling og resirkulering av DEWALT-produkter etter at de har utspilt sin rolle. For å benytte deg av denne tjenesten, vennligst returner produktet ditt til et av våre autoriserte serviceverksteder, som vil samle inn produktene for oss.
PORTUGUÊS BERBEQUIM/APARAFUSADOR A BATERIA DC740/DC750 Parabéns! Os seguintes símbolos são usados neste manual: Escolheu uma ferramenta DEWALT. Muitos anos de experiência, um desenvolvimento contínuo de produtos e o espírito de inovação fizeram da DEWALT um dos parceiros mais fiáveis para os utilizadores profissionais. Indica risco de ferimentos, perda de vida ou danos à ferramenta no caso do nãocumprimento das instruções deste manual. Dados técnicos Indica tensão eléctrica.
PORTUGUÊS Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Alemanha Regras gerais de segurança Aviso! Leia todas as instruções. O não cumprimento das instruções a seguir podem causar choque eléctrico, incêndio e/ou graves lesões. O termo “ferramenta eléctrica” utilizado a seguir refere-se a ferramentas eléctricas com ligação à corrente eléctrica (com cabo) ou operadas a bateria (sem fios). GUARDE BEM ESTAS INSTRUÇÕES.
PORTUGUÊS f Use vestuário apropriado. Não use roupa larga ou jóias. Mantenha o cabelo, roupa e luvas afastadas de partes em movimento. Roupas largas, jóias ou cabelos longos podem ser agarradas por partes em movimento. g Se for prevista a montagem de dispositivos de aspiração de pó e de dispositivos de recolha, assegure-se de que estão ligados e que são utilizados de forma correcta. A utilização destes dispositivos reduz os riscos provocados por pó.
PORTUGUÊS Regras adicionais de segurança para baterias Perigo de incêndio! Evite o curto-circuito dos contactos da bateria solta. Não armazene ou transporte a bateria sem a tampa de protecção fornecida estar colocada nos contactos. • O líquido da bateria, uma solução de hidróxido de potássio, pode ser nocivo. Em caso de contacto com a pele, lave imediatamente com água. Neutralize com um ácido suave, como sumo de limão ou vinagre.
PORTUGUÊS 9 10 11 12 Bateria Manipulos de fixação Carregador Indicator da carga (vermelho) Segurança eléctrica O carregador foi concebido para uma única tensão. Verifique sempre se a tensão corresponde à voltagem indicada na placa de identificação. O seu carregador DEWALT tem duplo isolamento em conformidade com o estipulado na norma EN 60745, não sendo, por isso, necessária uma ligação à terra.
PORTUGUÊS • Insira a broca até onde fôr possível e puxe-a ligeiramente para fora. • Aperte bem rodando a manga no sentido do relógio. • Para retirar a broca, proceda de forma inversa. Seleccione o modo de operação ou controlo do torque (fig. D) O anel desta ferramenta tem 15 posições para regular o torque, adaptando-o ao tamanho do parafuso e ao material da peça de trabalho. Para regular o torque, consulte a secção “Operações de aparafusar e desaparafusar”.
PORTUGUÊS • Se a embraiagem entrar em funcionamento demasiado cedo, regule o anel para aumentar o valor de torque, conforme necessário. Perfuração (fig. A) • Seleccione o modo de perfuração rotativa usando o anel (4). Perfuração em metal • Utilize um lubrificante de corte sempre que pretender furar metais. As excepções são o ferro e o bronze, que deverão ser perfurados a seco. Perfuração em madeira • Os furos em madeira podem ser efectuados com as mesmas brocas utilizadas para furar metal.
PORTUGUÊS GARANTIA Bateria de substitução Este bateria de longa duração deve ser substiuída, quando deixar de ter a potência necessária ão trabalho, que dava anteriormente. Ao fim da sua actividade, desfaça-se dele da maneira menos nociva para o nosso ambiente: • Consuma as baterias completamente e depois retire o jogo de baterias da ferramenta. • As baterias NiCd/NiMH são recicláveis. Leve-as ao seu concessionário ou a uma estação de reciclagem.
SUOMI AKKUISKUPORAKONE/RUUVINVÄÄNNIN DC740/DC750 Onneksi olkoon! Tässä käyttöohjeessa käytetään seuraavia merkkejä: Olet valinnut DEWALT-työkalun. Monivuotisen kokemuksen, ahkeran tuotekehittelyn ja uudistusten ansiosta DEWALT on yksi ammattikäyttäjien luotettavimmista yhteistyökumppaneista. Osoittaa henkilövahingon, hengenmenetyksen tai konevaurion vaaraa, mikäli tämän käyttöohjeen neuvoja ei noudateta. Tekniset tiedot Jännite Kuormittamaton kierrosnopeus I. vaihde II.
SUOMI Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Saksa Varoitus! Kaikki ohjeet täytyy lukea. Alla olevien ohjeiden noudattamisen laiminlyönti saattaa johtaa sähköiskuun, tulipaloon ja/tai vakavaan loukkaantumiseen. Seuraavassa käytetty käsite ”sähkötyökalu” käsittää verkkokäyttöisiä sähkötyökaluja (verkkojohdolla) ja akkukäyttöisiä sähkötyökaluja (ilman verkkojohtoa). SÄILYTÄ NÄMÄ OHJEET HYVIN.
SUOMI 4 Sähkötyökalujen käyttö ja hoito a Älä ylikuormita laitetta. Käytä kyseiseen työhön tarkoitettua sähkötyökalua. Sopivaa sähkötyökalua käyttäen työskentelet paremmin ja varmemmin tehoalueella, jolle sähkötyökalu on tarkoitettu. b Älä käytä sähkötyökalua, jota ei voida käynnistää ja pysäyttää virtakytkimestä. Sähkötyökalu, jota ei enää voida käynnistää ja pysäyttää käynnistyskytkimellä, on vaarallinen ja se täytyy korjata.
SUOMI Akun ja laturin etiketit Akun ja laturin etiketeistä näet seuraavat merkit: 1 Käyttöohje 1 Hajoituskuva 100% Lataus käynnissä 100% Akku latautunut Akku viallinen Älä kosketa akun napoja sähköä johtavilla esineillä Älä yritä ladata viallisia akkuja Lue käyttöohje Tarkoitettu ainoastaan DEWALT-akkujen lataamiseen; muut saattavat haljeta ja aiheuttaa henkilö- ja muita vahinkoja Laturi ei saa kastua Vaihda viallinen johto välittömästi +40 ˚c +4 ˚c Latauslämpötila +4 °C ja +40 °C välillä Hävitä a
SUOMI Asennus ja säädöt • Poista akku koneesta aina ennen asennuksia ja säätöjä. • Sammuta kone aina (off) ennen kuin poistat akkupaketin. Käytä ainoastaan DEWALT-akku ja latauslaite. Akkupaketti (kuva A & B) Akkujen lataaminen (kuva A) Kun akut ladataan ensimmäisen kerran tai pitkän varastoajan jälkeen, ne varautuvat vain noin 80 %:sti. Usean purkaus/latauskerran jälkeen akut latautuvat täyteen tehoonsa. Tarkista verkkokytkentä aina ennen kuin alat ladata akkuja.
SUOMI • Työnnä aina kaksiasentoinen valitsin kokonaan eteen tai kokonaan taakse. • Älä vaihda vaihteita koneen käydessä täydellä nopeudella äläkä muutoinkaan koneen käydessä. Käyttöohjeet Noudata aina turvallisuusohjeita ja voimassa olevia sääntöjä. Varo työskennellessäsi sähkö- ja vesijohtoja. Kuormita konetta järkevästi. Liiallinen voiman käyttö ei nopeuta poraamista, vaan vähentää työkalun tehoa ja saattaa lyhentää koneen käyttöikää.
SUOMI Kun DEWALT -koneesi on käytetty loppuun, älä hävitä sitä kotitalousjätteen mukana. Tämä tuote on kerättävä erikseen. Käytettyjen tuotteiden ja pakkausten erillinen keräys mahdollistaa materiaalien kierrätyksen ja uudelleenkäytön. Kierrätettyjen materiaalien uudelleenkäyttö auttaa ehkäisemään ympäristön saastumisen ja vähentää raaka-aineiden kysyntää.
SVENSKA UPPLADDNINGSBAR BORRMASKIN/ SKRUVDRAGARE DC740/DC750 Vi gratulerar! Följande symboler har använts i handboken: Du har valt ett DEWALT verktyg. Mångårig erfarenhet, ihärdig produktutveckling och förnyelse gör DEWALT till ett av de mest pålitliga namnen för professionella användare. Anger risk för personskada, livsfara eller skada på verktyg vid ouppmärksamhet inför de instruktioner som ges i handboken. Tekniska data Spänning Varvtal obelastad växel I växel II Max.
SVENSKA Director Engineering and Product Development Horst Großmann DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Tyskland Allmänna säkerhetsregler Varning! Samtliga anvisningar ska läsas. Fel som uppstår till följd av att anvisningarna nedan inte följts kan orsaka elchock, brand och/eller allvarliga kroppsskador. Nedan använt begrepp ”Elverktyg” hänför sig till nätdrivna elverktyg (med nätsladd) och till batteridrivna elverktyg (sladdlösa). TA VÄL VARA PÅ SÄKERHETSANVISNINGARNA.
SVENSKA 4 Bruk och skötsel av elverktyg a Överbelasta inte elverktyget. Använd rätt elverktyg för det aktuella arbetet. Med ett lämpligt elverktyg kan du arbeta bättre och säkrare inom angivet effektområde. b Ett elverktyg med defekt strömbrytare får inte längre användas. Ett elverktyg som inte kan kopplas till eller från är farligt och måste repareras. c Dra stickproppen ur vägguttaget innan inställningar utförs, tillbehörsdelar byts ut eller elverktyget ställs undan.
SVENSKA Använd aldrig ett sprucket eller skadat batteripaket Läs bruksanvisningen Endast för laddning av DEWALT batterier; andra batterier kan spricka och förorsaka personskada och skada på verktyget Får ej utsättas för väta Byt ut defekt sladd omedelbart +40 ˚c +4 ˚c Temperaturområde för uppladdning +4 °C till +40 °C När detta batteripaket har nått sin tekniska livslängd, tänk på miljön och släng batteripaketet enligt gällande miljöföreskrifter Batteripaketet får ej eldas upp Kontroll av förpackningen
SVENSKA Batteripaket (fig. A & B) Laddning av batteripaketet (fig. A) Första gången ett batteri laddas, eller när det har legat en längre tid, kan det bara laddas till 80%. Efter några laddnings-/urladdningscykler uppnår batteripaketet full kapacitet. Kontrollera alltid nätanslutningen innan batteripaketet laddas. Om nätanslutningen fungerar men batteripaketet inte laddas, tag laddaren till en godkänd DEWALT serviceverkstad. Under laddningen kan laddaren och batteripaketet kännas varma.
SVENSKA Se till att du vet var rör- och elledningar befinner sig. Utöva endast lätt tryck på maskinen. Större tryck gör inte att det går fortare att borra, men reducerar maskinens prestanda och gör att det slits fortare. För att reducera bromsningen när verktyget bryter genom, reducera trycket på borrspetsen när du nästan är färdig. Håll motorn igång medan du drar ut verktyget ur det borrade hålet. Detta förhindrar att verktyget fastnar. Innan Du börjar: • Se till att batteripaketet är (helt) laddat.
SVENSKA Enligt lokal lagstiftning kan det förekomma särskilda insamlingar av uttjänt elutrustning från hushåll, antingen vid kommunala miljöstationer eller hos detaljhandlaren när du köper en ny produkt. DEWALT erbjuder en insamlings- och återvinningstjänst för DEWALT-produkter när de en gång har tjänat ut. För att du skall kunna utnyttja den, ber vi dig att återlämna produkten till en auktoriserad reparations- och servicerepresentant som samlar in produkterna för vår räkning.
TÜRKÇE ŞARJLI MATKAP/TORNAVİDA TAKIMI DC740/DC750 Tebrikler! Bir D E WALT aletini seçmiş bulunuyorsunuz. Ürün geliştirme ve yenilemede y llar n deneyimi D E WALT’ profesyonel kullan c lar işin en güvenilir partnerlerden biri haline getirmektedir. Bu k lavuzun tümünde, aşağ daki semboller kullan lm şt r: Bu k lavuzdaki talimatlara uyulmamas halinde, yaralanma, ölüm veya aletin hasar görmesi tehlikesi olduğunu gösterir. Teknik veriler Voltaj V Yüksüz h z 1. viteste min -1 2.
TÜRKÇE m/s 2 DC740 DC750 3,54 3,54 2 a Mühendislik ve Ürün Geliştirme Müdürü Horst Großmann b D E WALT, Richard-Klinger-Straße 11, D-65510, Idstein, Almanya c Genel emniyet kurallar/ Dikkat! Bu talimat/n bütün hükümlerini okuyun. Aşağ/daki talimat hükümlerine uyarken hata yap/lacak olursa, elektrik çarpmalar/, yang/n ve/veya ağ/r yaralanmalara neden olunabilir.
TÜRKÇE c d e f g 4 a b c 92 Aletinizin kontrolünüz d/ş/nda çal/şmamas/ için gerekli önlemleri al/n. Prize takmadan önce açma düğmesinin kapal/ konumda olmas/na dikkat edin. Elektrikli aletlerin parmağ n z açma düğmesi üzerinde taş nmas veya aç k olarak prize tak lmas kazalara davetiye ç kar r. Aleti çal/şt/rmadan önce ayar aletlerini veya tornavidalar/ aletten uzaklaşt/r/n. Dönen alet parças na temas halinde bulunan bir uç veya anahtar yaralanmalara neden olabilir. Öne doğru aş/r/ eğilmeyin.
TÜRKÇE 100% d e 6 a Kullan/m d/ş/nda bulunan aküleri, kontaklar aras/nda köprüleme yapma olas/l/ğ/ bulunan büro ataçlar/, madeni paralar, anahtarlar, çiviler, vidalar veya diğer küçük metal eşya ve cisimlerden uzak tutun. Akü kontaklar aras ndaki bir k sa devre yanmalara veya yang n ç kmas na neden olabilir. Yanl/ş kullan/m durumunda akünün d/ş/na s/v/lar s/zabilir. Bu s/v/lara temas etmeyin. Yanl/şl/kla aküden s/zan s/v/lara temas ederseniz, temas yerini hemen su ile y/kay/n.
TÜRKÇE • Nakliye s ras nda alette, parçalar nda veya aksesuarlar nda hasar oluşup oluşmad ğ n kontrol edin. • Aleti kullanmadan önce, bu k lavuzu iyice okuyup anlamaya zaman ay r n. Tan/m (şekil A) Şarjl matkap/tornavida tak m n z DC740/ DC750 profesyonel delme ve vidalama işleri için geliştirilmiştir.
TÜRKÇE Gösterge, takriben bir saat sonra yan p sönmeye son vercek ve sürekli yanmaya başlayacakt r. Akünüz art k tam olarak şarj edilmiştir. Akü tak m istenildiği zaman ç kart labilir veya daha uzun süre (maksimum 14 gün) şarj cihaz na bağl b rak labilir. Akünün tak/lmas/ ve ç/kart/lmas/ • Aküyü şarj yerine oturtun. • Aküyü şarj yerinden almak için iki serbest b rakma düğmesine (10) ayn anda bas p aküyü ç kart n.
TÜRKÇE Cihaza hafif bir bas nç uygulay n z. Fazla bast rmak, delme h z n artt rmaz, ancak cihaz n performans n ve önrümü azalt r. İşlenen malzemenin delinmesiyle görülen boğulmay önlemek için, işlemin sonuna doğru delme noktas bas nc n kademeli olarak azalt n. Matkap ucunu aç lan delikten ç kart rken motoru çal şt rmaya devam edin. Böylece matkap ucunun s k şmas önlenir. Kullanmadan önce: • Akünüzün (tam) şarjl olmas n sağlay n. • Uygun ucu tak n. • Delinecek deliği işaretleyin.
TÜRKÇE D E WALT ürününüz şayet bir gün değiştirilmesi gerekiyor ise, veya bundan böyle sizin için kullan lmayacak ise bu aleti normal ev at klar ile çöpe atmay n. Bu ürünü ayr bir biriktirme için ay r n. Kullan lm ş ürünlerin ayr ca biriktirilmesi ve paketlenmesi malzemelerin yeniden dönüşümüne ve yeniden kullan m na izin vermektedir. Yeniden dönüşümü olan malzemelerin yeniden kullan m , çevre kirliliğini önlenmesine yard m etmekte ve ham maddeye olan talebi indirgemektedir.
TÜRKÇE GARANTİ • 30 GÜNLÜK RİSKSİZ MÜŞTERİ MEMNUNİYETİ GARANTİSİ • D E WALT ağ r hizmet tipi endüstriyel aletinizin performans sizi tam olarak tatmin etmiyorsa, 30 gün içinde takas için yetkili bayinize geri götürebilirsiniz. Sat n alma belgesinin ibraz şartt r. • ÜCRETSİZ BİR YILLIK SERVİS KONTRATİ • Bir y ll k tam garantiye ek olarak, tüm D E WALT aletleri bir y l süreyle ücretsiz servis desteğine de sahiptir.
∂§§∏¡π∫∞ ∫ƒ√À™∆π∫√ E¶∞¡∞º√ƒ∆π∑√ªE¡√ ¢ƒ∞¶∞¡√/∫∞∆™∞µπ¢π DC740/DC750 £ÂÚÌ¿ Û˘Á¯·ÚËÙ‹ÚÈ·! ¢È·Ï¤Í·Ù ¤Ó· ·fi Ù· Ì˯·Ó‹Ì·Ù· Ù˘ DEWALT. ∏ Ôχ¯ÚÔÓË ÂÌÂÈÚ›· Ù˘ DEWALT, Ë Û˘Ó¯‹˜ ÂͤÏÈÍË ÙˆÓ ÚÔ˚fiÓÙˆÓ Ù˘ Î·È Ë ÂÊ·ÚÌÔÁ‹ ηÈÓÔÙÔÌÈÒÓ ÙËÓ Î·ıÈÛÙÔ‡Ó ¤Ó·Ó ·fi ÙÔ˘˜ Èfi ·ÍÈfiÈÛÙÔ˘˜ Û˘ÓÂÚÁ¿Ù˜ ÙˆÓ Â·ÁÁÂÏÌ·ÙÈÒÓ. ™ÙȘ ·ÚÔ‡Û˜ Ô‰ËÁ›Â˜ ¯ÚËÛÈÌÔÔÈÔ‡ÓÙ·È Ù· ·ÎfiÏÔ˘ı· ۇ̂ÔÏ·: ™˘Ì‚ÔÏ›˙ÂÈ Î›Ó‰˘ÓÔ ÙÚ·˘Ì·ÙÈÛÌÔ‡ ‹ ı·Ó¿ÙÔ˘ ‹ ‚Ï¿‚˘ ÙÔ˘ ÂÚÁ·Ï›Ԣ Û ÂÚ›ÙˆÛË Ô˘ ‰ÂÓ ÙËÚËıÔ‡Ó ÔÈ Ô‰ËÁ›Â˜ ¯Ú‹Ûˆ˜.
∂§§∏¡π∫∞ ¢È¢ı˘ÓÙ‹˜ ∞Ó¿Ù˘Í˘ ¶ÚÔ˚fiÓÙˆÓ Horst Großmann ‚ DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, °ÂÚÌ·ÓÈ· Á °ÂÓÈÎÔ› ηÓfiÓ˜ ·ÛÊ·Ï›·˜ ¶ÚÔÂȉÔÔ›ËÛË! ¢È·‚¿ÛÙ fiϘ ÙȘ ˘Ô‰Â›ÍÂȘ. ∏ ÌË Ù‹ÚËÛË fiÏˆÓ ÙˆÓ ·Ú·Î¿Ùˆ ˘Ô‰Â›ÍÂˆÓ ÌÔÚ› Ó· ÚÔηϤÛÂÈ ËÏÂÎÙÚÔÏËÍ›·, ˘ÚηÁÈ¿ ‹/Î·È ÛÔ‚·ÚÔ‡˜ ÙÚ·˘Ì·ÙÈÛÌÔ‡˜.
∂§§∏¡π∫∞ Á ∞ÔʇÁÂÙ ÙËÓ ·ı¤ÏËÙË ı¤ÛË Û ÏÂÈÙÔ˘ÚÁ›· ÙÔ˘ ËÏÂÎÙÚÈÎÔ‡ ÂÚÁ·Ï›Ԣ. µÂ‚·Èˆı›ÙÂ, fiÙÈ Ô ‰È·ÎfiÙ˘ ÏÂÈÙÔ˘ÚÁ›·˜ ‚Ú›ÛÎÂÙ·È ÛÙË ı¤ÛË “OFF” ÚÈÓ Û˘Ó‰¤ÛÂÙ ÙÔ ËÏÂÎÙÚÈÎfi ÂÚÁ·ÏÂ›Ô ÛÙËÓ Ú›˙·. ∞Ó ÌÂٷʤÚÂÙ ÙÔ ËÏÂÎÙÚÈÎfi ÂÚÁ·ÏÂ›Ô ¤¯ÔÓÙ·˜ ÙÔ ‰¿ÎÙ˘Ïfi Û·˜ ¿Óˆ ÛÙÔ ‰È·ÎfiÙË ÏÂÈÙÔ˘ÚÁ›·˜ ‹ ·Ó Û˘Ó‰¤ÛÂÙ ÙÔ ËÏÂÎÙÚÈÎfi ÂÚÁ·ÏÂ›Ô ÛÙËÓ Ú›˙· fiÙ·Ó Ô ‰È·ÎfiÙ˘ ÏÂÈÙÔ˘ÚÁ›·˜ ‚Ú›ÛÎÂÙ·È ÛÙË ı¤ÛË “ON”, ·˘Ùfi ÌÔÚ› Ó· Ô‰ËÁ‹ÛÂÈ Û ÛÔ‚·ÚÔ‡˜ ÙÚ·˘Ì·ÙÈÛÌÔ‡˜.
∂§§∏¡π∫∞ ‚ Á ‰  ∏ ÙÔÔı¤ÙËÛË Ù˘ Ì·Ù·Ú›·˜ ÛÙÔ ËÏÂÎÙÚÈÎfi ÂÚÁ·ÏÂ›Ô fiÙ·Ó Ô ‰È·ÎfiÙ˘ ÏÂÈÙÔ˘ÚÁ›·˜ ‚Ú›ÛÎÂÙ·È ÛÙË ı¤ÛË “ON” ÌÔÚ› Ó· Ô‰ËÁ‹ÛÂÈ Û ·Ù˘¯‹Ì·Ù·. ¡· ·ӷÊÔÚÙ›˙ÂÙ ÙȘ ̷ٷڛ˜ ÌfiÓÔ Ì ÙÔ ÊÔÚÙÈÛÙ‹ Ô˘ ÚԂϤÂÈ Ô Î·Ù·Û΢·ÛÙ‹˜. EÓ·˜ ÊÔÚÙÈÛÙ‹˜ Ô˘ Â›Ó·È Î·Ù¿ÏÏËÏÔ˜ ÁÈ· ¤Ó·Ó Ù‡Ô Ì·Ù·Ú›·˜ ÌÔÚ› Ó· ÚÔηϤÛÂÈ ˘ÚηÁÈ¿ fiÙ·Ó ¯ÚËÛÈÌÔÔÈËı› ÁÈ· ÙË ÊfiÚÙÈÛË Î¿ÔÈÔ˘ ¿ÏÏÔ˘ Ù‡Ô˘ Ì·Ù·Ú›·˜. ¡· ¯ÚËÛÈÌÔÔț٠ٷ ËÏÂÎÙÚÈο ÂÚÁ·Ï›· ÌfiÓÔ Ì ÙȘ ÚÔ‚ÏÂfiÌÂÓ˜ ÁÈ’ ·˘Ù¿ ̷ٷڛ˜.
∂§§∏¡π∫∞ +40 ˚c +4 ˚c ¡· ¯ÚËÛÈÌÔÔÈÂÈÙ ÌÔÓÔ Û ıÂÚÌÔÎÚ·ÛȘ ·Ô 4Æ Âˆ˜ 40 ÆC ∫·Ù¿ ÙÔ Ù¤ÏÔ˜ Ù˘ Ù¯ÓÈ΋˜ ÙÔ˘ ˙ˆ‹˜, ·ÔÚÚ›„Ù ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ Ì ÙËÓ ‰¤Ô˘Û· ÊÚÔÓÙ›‰· ÁÈ· ÙÔ ÂÚÈ‚¿ÏÏÔÓ ªË η›Ù ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ EÏÂÁ¯Ô˜ ÙÔ˘ ÂÚȯÔ̤ÓÔ˘ Ù˘ Û˘Û΢·Û›·˜ ™ÙË Û˘Û΢·Û›· ˘¿Ú¯Ô˘Ó: 1 E·Ó·ÊÔÚÙÈ˙fiÌÂÓÔ ‰Ú¿·ÓÔ/ηÙÛ·‚›‰È 1 ºÔÚÙÈÛÙ‹˜ 1 £‹ÎË Ì·Ù·ÚÈÒÓ (Ù‡· K) 2 £‹Î˘ Ì·Ù·ÚÈÒÓ (Ù‡· KA Î·È KB) 1 ª‡ÙË 1 ∫È‚ÒÙÈÔ (Ù‡· K ÌfiÓ·) 1 º˘ÏÏ¿‰ÈÔ Ô‰ËÁÈÒÓ 1 ∞Ó·Ï˘ÙÈÎfi Û¯¤‰ÈÔ • EϤÁÍÙ ÙÔ ÂÚÁ·Ï›Ô, Ù· ·ÓÙ·ÏÏ·ÎÙÈο Î
∂§§∏¡π∫∞ • ¶¿ÓÙ· ı¤ÙÂÙ ÂÎÙfi˜ ÙÔ ÂÚÁ·ÏÂ›Ô ÚÈÓ ‚¿ÏÂÙ ‹ ·Ê·ÈÚ¤ÛÂÙ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ. ÃÚËÛÈÌÔÔÈËÙ ÌÔÓÔ Ì·Ù·ÚȘ Î·È ÊÔÚÙÈÛÙ‹ DEWALT. ™˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ (ÂÈÎ. A & B) ºfiÚÙÈÛË Û˘ÁÎÚÔÙ‹Ì·ÙÔ˜ Ì·Ù·ÚÈÒÓ (ÂÈÎ. A) √Ù·Ó ÊÔÚÙ›˙ÂÙ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ ÁÈ· ÚÒÙË ÊÔÚ¿, ‹ ÌÂÙ¿ ·fi Ì·ÎÚÔ¯ÚfiÓÈ· ·Ôı‹Î¢ÛË, ı· ÊÔÚÙÈÛÙ› ÌfiÓÔ Î·Ù¿ 80%. ªÂÙ¿ ·fi ·ÚÎÂÙÔ‡˜ ·ÎÏÔ˘˜ ÊfiÚÙÈÛ˘ Î·È ÂÎÊfiÚÙÈÛ˘, ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ ı· ·ÔÎÙ‹ÛÂÈ Ï‹ÚË ¯ˆÚËÙÈÎfiÙËÙ¿.
¢È·ÎfiÙ˘ ηÓÔÓÈ΋˜/·ÓÙ›ÛÙÚÔÊ˘ ÂÚÈÛÙÚÔÊ‹˜ (ÂÈÎ. E) • °È· Ó· ÂÈϤÍÂÙ ηÓÔÓÈ΋ ‹ ·ÓÙ›ÛÙÚÔÊË ÂÚÈÛÙÚÔÊ‹, ¯ÚËÛÈÌÔÔÈ‹ÛÙ ÙÔÓ ‰È·ÎfiÙË Î·ÓÔÓÈ΋˜/·ÓÙ›ÛÙÚÔÊ˘ ÂÚÈÛÙÚÔÊ‹˜ (2) fiˆ˜ Ê·›ÓÂÙ·È (‰Â›Ù ٷ ‚¤ÏË ¿Óˆ ÛÙÔ ÂÚÁ·Ï›Ô). ¶ÚÈÓ ·ÏÏ¿ÍÂÙ ÙË ÊÔÚ¿ ÂÚÈÛÙÚÔÊ‹˜, ÂÚÈ̤ÓÂÙ ¿ÓÙÔÙ ӷ ÛÙ·Ì·Ù‹ÛÂÈ ÂÓÙÂÏÒ˜ Ë Î›ÓËÛË ÙÔ˘ ÌÔÙ¤Ú. °È· Ó· ÂÏ·¯ÈÛÙÔÔÈ‹ÛÂÙ ÙÔ ÛÙÔÏ¿ÚÈÛÌ· ηٿ ÙË ‰È¿ÓÔÈÍË, ÌÂÈÒÓÂÙ ÚÔԉ¢ÙÈο ÙËÓ ›ÂÛË ÙÔ˘ ÛËÌ›Ԣ ‰È¿ÙÚËÛ˘ ÚÔ˜ ÙÔ Ù¤ÏÔ˜ Ù˘ ÏÂÈÙÔ˘ÚÁ›·˜.
¢È¿ÙÚËÛË Û ̤ٷÏÏÔ • ÃÚËÛÈÌÔÔț٠ÏÈ·ÓÙÈÎfi ÎÔ‹˜ fiÙ·Ó Î¿ÓÂÙ ‰È¿ÙÚËÛË Û ̤ٷÏÏ·. √È ÂÍ·ÈÚ¤ÛÂȘ Â›Ó·È Ô ¯˘ÙÔÛ›‰ËÚÔ˜ Î·È Ô ÔÚ›¯·ÏÎÔ˜, ÛÙȘ Ôԛ˜ Ë ‰È¿ÙÚËÛË Ó· Á›ÓÂÙ·È ÍËÚ¿. ¢È¿ÙÚËÛË Û ͇ÏÔ • √¤˜ Û ͢ÏÔ ÌÔÚÔ˘Ó Ó· Á›ÓÔıÓ Ì ٷ ›‰È· ÙÚ˘¿ÓÈ· Ô˘ ¯ÚËÛÈÌÔÔÈÔ˘ÓÙ·È ÁÈ· Ù· ̤ٷÏÏ·. ∞˘Ù¿ Ù· ¿ÎÚ· ÌÔÚÔ˘Ó Ó· ˘ÂÚıÂÚÌ·ÓıÔ˘Ó ÂÎÙfi˜ Â¿Ó ÙÚ·‚ÈÔ˘ÓÙ·È ¤Íˆ Û˘¯Ó¿ ÁÈ· Ó· ηı·Ú›˙ÔÓÙ·È ·fi Ù· ÚÔηӛ‰È· ·fi ÙȘ ·˘Ï·ÎÒÛÂȘ. • °È· ÌÂÁ·Ï˘ÙÂÚ˜ Ô¤˜, ¯ÚËÛÈÌÔÔÈ‹ÛÙ ͢ÏÈÓ· ¿ÎÚ· ∆Ú˘¿ÓÈ· ͢ÏÔ˘ Û ¯·ÌËϤ˜ Ù·¯˘ÙËÙ˜.
E°°À∏™∏ E·Ó·ÊÔÚÙË˙fiÌÂÓÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ ∞˘Ùfi ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ Ì·ÎÚ¿˜ ‰È·ÚΛ·˜ Ú¤ÂÈ Ó· ÊÔÚÙ›˙ÂÙ·È fiÙ·Ó ‰ÂÓ ÌÔÚ› Ó· ·Ú¤¯ÂÈ ÈÛ¯‡ ÁÈ· ÂÚÁ·Û›Â˜ Ô˘ Á›ÓÔÓÙ·Ó Â‡ÎÔÏ· ÚÔËÁÔ˘Ì¤Óˆ˜. ∫·Ù¿ ÙÔ Ù¤ÏÔ˜ Ù˘ Ù¯ÓÈ΋˜ ÙÔ˘ ˙ˆ‹˜, ·ÔÚÚ›„Ù ÙÔ Ì ÙËÓ ‰¤Ô˘Û· ÊÚÔÓÙ›‰· ÁÈ· ÙÔ ÂÚÈ‚¿ÏÏÔÓ: • EÍ·ÓÙÏ‹ÛÙ ϋڈ˜ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ, Î·È ÛÙË Û˘Ó¤¯ÂÈ· ·Ê·ÈÚ¤ÛÙ ÙÔ ·fi ÙÔ ÂÚÁ·Ï›Ô. • ∆· ÛÙÔȯ›· NiCd/NiMH Â›Ó·È ·Ó·Î˘ÎÏÒÛÈÌ·. ªÂٷʤÚÙ ٷ ÛÙÔÓ ·ÓÙÈÚfiÛˆfi Û·˜ ‹ Û ÙÔÈÎfi ÛÙ·ıÌfi ·Ó·Î‡ÎψÛ˘.
Belgique et Luxembourg België en Luxemburg DEWALT Mechelen Campus, Schaliënhoevedreef 20E B-2800 Mechelen Tel: +32 (0)015 - 15 47 9211 Fax: +32 (0)015 - 15 47 9210 www.dewalt.com Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70 20 15 10 Fax: 36 94 49 01 www.dewalt-nordic.com Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de EÏÏ¿˜ Black & Decker (EÏÏ¿˜) ∞.E.