INSTRUCTION MANUAL DC800-XE HEAVY-DUTY 36V 13 MM (1/2") CORDLESS IMPACT WRENCH
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. ELECTRICAL SAFETY a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
b. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. c. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. d.
• Bits, sockets and tools get hot during operation. Wear gloves when touching them. • Do not operate this tool for long periods of time. Vibration caused by tool action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods. WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: • ANSI Z87.
• NEVER attempt to connect 2 chargers together. • The charger is designed to operate on standard household electrical power. Do not attempt to use it on any other voltage. • Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock, or electrocution.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention. WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame. • Charge the battery packs only in DEWALT chargers. • DO NOT splash or immerse in water or other liquids. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40˚C (105°F) (such as outside sheds or metal buildings in summer).
three red lights will flash together with two fast blinks followed by a pause. This indicates that the power souce is out of limits. BAD BATTERY The charger can detect a weak or damaged battery. The three red lights will flash together with rapid blinking. The battery will no longer charge and should be returned to a service center or a collection site for recycling. BAD CHARGER The charger will detect if it is not functioning properly.
FIG. 3 CAUTION: Use only impact sockets. Non-impact sockets may break and cause a hazardous condition. Inspect sockets prior to use to ensure that it contains no cracks. To remove a socket, depress the detent pin through the hole, using a small pointed object, and pull the socket off. Usage CAUTION: Ensure fastener and/or system will withstand the level of torque generated by the tool. Excessive torque may cause breakage and possible personal injury. 1. Place the socket on the fastener head.
CHARGER CLEANING INSTRUCTIONS WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. This warranty gives you specific legal rights and you may have other rights under the provisions of the Consumer Guarantee Act 1993 (New Zealand only), Trade Practices Act 1974 and State Legislation (Australia only).
9
DEWALT Battery and Charger Systems Battery Output Nominal Chargers/Charge Time 240 Volts 12 Volts Cat. Number Voltage Amp Hour 97014 98014 DW9106 DW9107 DW9108 DW9115 DW9116 DW9117 DW9118 DE9116 DE9118 DW911 DC011 DW0245 DE2046 DE9000 DW9109 DW0242 DE0240-XJ DW0240 DW9096 DE9095-XJ DE9091-XJ DW9091 DC9071 DE9074-XJ DW9072 DE9071-XJ DW9071 DW9050 DW9063 DW9062 DW9061 DW9048 DW9057 DW9046 DC9096 DC9091 DC9036 24 24 24 18 18 14.4 14.4 12 12 12 12 12 12 9.6 9.6 9.6 9.6 7.2 7.2 18 14.