www. .
Copyright DEWALT 2
A 1
B C 2 D
F E DC987, DC988 DC980, DC981, DC984 9 G 3
ENGLISH CORDLESS DRIVER/(PERCUSSION) DRILL DC980, DC981, DC984, DC987, DC988 Congratulations! You have chosen a DEWALT power tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical Data Voltage V Type DC980 DC981 DC984 DC987 12 12 14.
ENGLISH significantly increase the exposure level over the total working period. the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job.
ENGLISH These products also comply with Directive 2004/108/ EC. For more information, please contact DEWALT at the following address or refer to the back of the manual. The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT. c) d) e) Horst Grossmann Vice President Engineering and Product Development DEWALT, Richard-Klinger-Straße 11, D-65510, Idstein, Germany 05.08.2009 WARNING: To reduce the risk of injury, read the instruction manual.
ENGLISH used. Use of dust collection can reduce dustrelated hazards. 4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
ENGLISH – Health hazards caused by breathing dust developed when working in wood. – Risk of personal injury due to flying particles. – Risk of personal injury due to prolonged use. Markings on Tool The following pictograms are shown on the tool: Read instruction manual before use. power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual.
ENGLISH Chargers LI-ION BATTERY PACKS ONLY The DE9116 charger accepts 7.2–18 V NiCd and NiMH batteries. Li-Ion batteries are designed with an Electronic Protection System that will protect the battery against overloading, overheating or deep discharge. The DE9135 charger accepts 7.2–18 V NiCd, NiMH or Li-Ion batteries. These chargers require no adjustment and are designed to be as easy as possible to operate. Charging Procedure DANGER: Electrocution hazard. 230 volts present at charging terminals.
ENGLISH SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM (NiCd) OR NICKEL METAL HYDRIDE (NiMH) • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. • A small leakage of liquid from the battery pack cells may occur under extreme usage or temperature conditions. This does not indicate a failure. However, if the outer seal is broken: a.
ENGLISH Have defective cords replaced immediately. Charge only between 4 °C and 40 °C. 8 Grip 9 Side handle (DC987, DC988) 10 Battery pack 11 Release buttons Discard the battery pack with due care for the environment. 12 Charger 13 Charging indicator (red) INTENDED USE Do not incinerate the battery pack NiMH, NiCd+ and Li-Ion. Your cordless driver/(percussion) drill has been designed for professional drilling and screwdriving applications. Charges NiMH and NiCd battery packs.
ENGLISH Auto-spindle Lock The auto-spindle lock is engaged when the transmission is stationary. The chuck sleeve can easily be turned with one hand while the other supports the unit. ASSEMBLY AND ADJUSTMENT WARNING: Prior to assembly and adjustment, always remove the battery pack. Always switch off the tool before inserting or removing the battery pack. WARNING: Use only DEWALT battery packs and chargers.
ENGLISH Screwdriving (fig. A) • Select forward or reverse rotation using the slider (2). • Set the collar (4) to position 1 and begin screwdriving (low torque). • If the clutch ratchets too soon, adjust the collar to increase the torque as required. Drilling (fig. A) • Select the drilling mode using the collar (4). • Select forward rotation. Drilling in Metal • Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry.
ENGLISH You can check the location of your nearest authorised repair agent by contacting your local DEWALT office at the address indicated in this manual. Alternatively, a list of authorised DEWALT repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com. Rechargeable Battery Pack This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before.
15
16
17
Belgique et Luxembourg België en Luxemburg Black & Decker - DEWALT Nieuwlandlaan 7, IZ Aarschot B156 B-3200 Aarschot Tel: +32 (0)015 - 15 47 9211 Fax: +32 (0)015 - 15 47 9210 www.dewalt.be Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70201511 Fax: 70224910 www.dewalt.dk Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Hellas) S.A.
