Product Manual

ManualsBrandsDEWALT ManualsPower Tool Accessories12-Volt to 20-Volt MAX Lithium-Ion Dual Port Jobsite Fast Charging Station with (2) USB Ports

service center or to your local retailer for recycling. You may also contact your local recycling center

for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

COMPONENTS (Fig. 1)

WARNING: Never modify the jobsite charging station or any part of it. Damage or personal injury

could result.

A. Battery pack

B. USB charging port

C. Jobsite charging station

Battery Pack Charging Procedure (Fig. 1)

The DCB102 jobsite charging station is designed to charge DEWALT 12–20V Max* Li-lon battery

packs and charge or supply power to USB compatible devices.

Be sure to read all safety instructions before using your charger. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack (A) into the correct charger port, as shown in Figure 1, making sure the

pack is fully seated in the charger. The red (charging) light will blink continuously indicating that

the charging process has started.

3. The completion of charge will be indicated by the red light remaining ON continuously. The pack

is fully charged and may be used at this time or left in the charger.

NOTE: The DCB102 jobsite charging station can simultaneously charge two battery packs.

USB Charging Ports (Fig. 1)

The DCB102 jobsite charging station (C) is equipped with two USB Type A charging ports (B). The

USB charging ports deliver 1.5 amps total current.

NOTE: Do not plug in devices that exceed the output ratings on the jobsite charging

station’s label. Doing so will shorten the charger's useful life.

WARNING: Read all charging warnings and instructions in manual for USB compatible device.

Plug the charger into an appropriate outlet and then insert a USB plug into one of the charging ports

(B) to supply power or charge your device.

Indicator Light Operation for Battery Packs

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

PROBLEM POWERLINE

Charge Indicators for Battery Packs

This charger is designed to detect certain problems that can arise. Problems are indicated by the red

light flashing at a fast rate. If this occurs, re-insert the battery pack into the charger. If the problem

persists, try a different battery pack to determine if the charger is working properly. If the new pack

charges correctly, then the original pack is defective and should be returned to a service center or

other collection site for recycling. If the new battery pack elicits the same trouble indication as the

original, have the charger and the battery pack tested at an authorized service center.

HOT/COLD DELAY

This charger has a hot/cold delay feature: when the charger detects a battery that is hot, it

automatically starts a delay, suspending charging until the battery has cooled. After the battery

has cooled, the charger automatically switches to the pack charging mode. This feature ensures

maximum battery life. The red light flashes long, then short while in the hot/cold delay mode.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge indicator showing pack

charged.

WEAK BATTERY PACKS: Weak batteries will continue to function but should not be expected to

perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack. The charger will

indicate faulty battery pack by refusing to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

PROBLEM POWER LINE

Some chargers have a Problem Power Line indicator. When the charger is used with some portable

power sources such as generators or sources that convert DC to AC, the charger may temporarily

suspend operation, flashing the red light with two fast blinks followed by a pause. This indicates the

power source is out of limits.

Important Charging Notes for Battery Packs

1. Longest life and best performance can be obtained if the battery pack is charged when the air

temperature is between 65°F and 75°F (18° – 24°C). DO NOT charge the battery pack in an

air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to the touch while charging. This is a normal

condition, and does not indicate a problem. To facilitate the cooling of the battery pack after

use, avoid placing the charger or battery pack in a warm environment such as in a metal shed

or an uninsulated trailer.

3. LITHIUM ION ONLY: A cold battery pack will charge at about half the rate of a warm battery

pack. The battery pack will charge at that slower rate throughout the entire charging cycle and

will not return to maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of the receptacle by plugging in a lamp or other appliance;

b. Check to see if the receptacle is connected to a light switch which turns the power off when

you turn out the lights;

c. Move the charger and battery pack to a location where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery pack and charger to your local service

center.

5. The battery pack should be recharged when it fails to produce sufficient power on jobs which

were easily done previously. DO NOT CONTINUE to use it under these conditions. Follow the

charging procedure. You may also charge a partially used pack whenever you desire with no

adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal chips,

steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when there is no battery pack in the

cavity. Unplug the charger before attempting to clean it.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the charger. Electric shock may

result.

WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic housing

of the battery pack breaks or cracks, return it to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat

or cold.

2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place

out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will

need to be recharged before use.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

MAINTENANCE

Cleaning

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and

grease may be removed from the exterior of the charger/battery pack using a cloth or soft non-

metallic brush. Do not use water or any cleaning solutions.

Repairs

The jobsite charging station and battery pack are not serviceable. There are no serviceable parts

inside the jobsite charging station or battery pack.

READ ALL OF THE INSTRUCTIONS IN THE BATTERY CHARGER SECTION OF THIS

MANUAL AND THE USB COMPATIBLE DEVICE MANUAL BEFORE ATTEMPTING TO

CHARGE THE BATTERY PACK FOR YOUR TOOL OR THE USB COMPATIBLE DEVICE.

If you have any questions, call 1-800-4-D

EWALT (1-800-433-9258).

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.

com or call 1-800-4-D

EWALT (1-800-433-9258). This warranty does not apply to accessories or

damage caused where repairs have been made or attempted by others. This warranty gives you

specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

2 YEARS FREE SERVICE ON D

EWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120, DCB127,

DCB201, DCB203 and DCB207

3 YEARS FREE SERVICE ON D

EWALT BATTERY PACKS

DCB200, DCB204

EWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any way. D

EWALT is not responsible

for any injury caused by tampering and may prosecute warranty fraud to the fullest extent permitted

by law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your D

EWALT Power Tool, Laser, or Nailer

for any reason, you can return it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels (fig. 2) become illegible or are

missing, call 1-800-4-D

EWALT (1-800-433-9258) for a free replacement.

FIG. 2

Déﬁ nitions: lignes directrices en matière

de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-

indicateur employé. Lire le mode d’emploi et porter une attention particulière à

ces symboles.

DANGER: indique une situation dangereuse imminente qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves.

AVERTISSEMENT : indique une situation potentiellement dangereuse qui,

si elle n’est pas évitée, pourrait entraîner la mort ou des blessures graves.

ATTENTION : indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, pourrait entraîner des blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de dommages corporels

mais qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE

OUTIL DEWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1 800 433-9258 (1-800-4-DEWALT).

AVERTISSEMENT ! Lire et comprendre toutes les directives. À

défaut de suivre les directives sous-mentionnées, un choc électrique, un

incendie et des blessures corporelles graves pourraient survenir.

CONSERVER CES CONSIGNES

DIRECTIVES DE SÉCURITÉ IMPORTANTES PROPRES À

TOUS LES CHARGEURS DE PILES

CONSERVER CES INSTRUCTIONS: ce manuel contient des directives importantes de sécurité

et d’utilisation relatives au chargeur de blocs-piles.

• Avant d’utiliser le chargeur, lire toute consigne et tout avertissement apposés sur le chargeur, le

bloc-piles et le produit utilisant le bloc-piles.

AVERTISSEMENT : risques de chocs électriques. Ne laisser aucun liquide pénétrer dans le

chargeur, des chocs électriques pourraient en résulter.

FIG. 1