Instruction Manual Guide D’utilisation Manual de instrucciones DCS570 20V Max* 7–1/4" (184 mm) Cordless Circular Saw Scie circulaire sans fil de 20 V max* 184 mm (7–1/4 po.) Sierra circular inalámbrica de 20 V Máx* 184 mm (7–1/4") If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos. 1-800-4-DeWALT final page size: 8.5 x 5.
English (original instructions) 1 Français (traduction de la notice d’instructions originale) ?? Español (traducido de las instrucciones originales) ??
English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
English GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool. 1) Work Area Safety a ) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
English into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Battery Tool Use and Care a ) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b ) Use power tools only with specifically designated battery packs.
English Lower Guard Function Safety Instructions a ) Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.
BATTERIES AND CHARGERS The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow charging procedures outlined. When ordering replacement battery packs, be sure to include the catalog number and voltage. Your tool uses a DeWALT charger. Be sure to read all safety instructions before using your charger. Consult the chart at the end of this manual for compatibility of chargers and battery packs.
English For example, Shipping Wh rating might indicate 3 x 40 Wh, meaning 3 batteries of 40 Watt hours each. The Use Wh rating might indicate 120 Wh (1 battery implied). Fuel Gauge Battery Packs (Fig. B) Some DeWALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in the battery pack.
English • • • • • • • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing. Do not operate the charger with a damaged cord or plug. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way.
English Hot/Cold Pack Delay When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery pack life. A cold battery pack will charge at a slower rate than a warm battery pack.
English OPERATION Fig. E 2 WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. 1 Installing and Removing the Battery Pack (Fig. D) NOTE: For best results, make sure your battery pack is fully charged.
English Lower Blade Guard Fig. F 16 8 Fig. G 6 11 WARNING: The lower blade guard is a safety feature which reduces the risk of serious personal injury. Never use the saw if the lower blade guard is missing, damaged, misassembled or not working properly. Do not rely on the lower blade guard to protect you under all circumstances. Your safety depends on following all warnings and precautions as well as proper operation of the saw.
English down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator. If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator. Kickback is more likely to occur when any of the following conditions exists. 1. IMPROPER WORKPIECE SUPPORT a.
English Bevel Angle Adjustment (Fig. A, J) The full range of the bevel adjustment is from 0° to 57°. The quadrant is graduated in increments of 1°. On the front of the saw is a bevel angle adjustment mechanism consisting of a calibrated quadrant and a bevel adjustment lever 10 . penciled cutting line so that the kerf falls into the waste or surplus material. Fig. L 9 To set the saw for a bevel cut 1. Loosen (counterclockwise) the bevel adjustment lever 10 and tilt shoe ( 5 , Fig.
English Cutting (Fig. M) Place the wider portion of the saw shoe on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As an example, Figure M illustrates the RIGHT way to cut off the end of a board. Always clamp work. Don’t try to hold short pieces by hand! Remember to support cantilevered and overhanging material. Use caution when sawing material from below. Be sure saw is up to full speed before blade contacts material to be cut.
English Accessories WARNING: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DeWALT recommended accessories should be used with this product. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DeWALT Industrial Tool Co.
DeWALT BATTERY AND CHARGER SYSTEMS Chargers/Charge Time (Minutes) Chargeurs/Durée de charge (Minutes) Cargadores de baterías/Tiempo de carga (Minutos) DCB103 DCB107 DCB112 DCB113 DCB114 DCB115 DCB116 X X X X X X X X X X X X X X X 40 X X X X X X X X X X X X X X X X X X X X X 60 100 X X X X X X 60 30 35 35 70 70 95 30 X 30 35 X 100 X X X X X X 60 30 35 35 70 70 95 30 X 30 35 X 100 X X X X X X 60 30 35 35 70 70 95 30 40 30 35 X 272 X X X X X X 140 70 90 90 185 185 240 60 X 60 90 X 170 X X X X X X
