Use and Care Manual

11
ENGLISH
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer SafetyAct.
• Register online at www.dewalt.com.
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a factory service
center or an authorized service center. Always use
identical replacementparts.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your smart
device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
moreinformation.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
20
that hold the Tool
Connect™ Chip protective cover
19
into thetool.
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
18
.
3. Ensure that the Tool Connect™ Chip is flush with the housing.
Secure it with the retaining screws and tighten thescrews.
4. Refer to Tool Connect™ Chip Instruction Sheet for
furtherinstructions.
Accessories

WARNING: Since accessories, other than
those offered by DeWALT, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
DeWALT recommended accessories should be used with
thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact
DeWALT. Call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
Cleaning

WARNING: Blow dirt and dust out of
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
Z87.1 approved eye protection when performing
thisprocedure.

WARNING: Never use solvents or other
harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened only
with water and mild soap. Never let any liquid get inside
the tool; never immerse any part of the tool into aliquid.
MAINTENANCE

WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.
Your
DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
• Install the battery pack
15
into the tool handle.
• Hold the blower with one hand as shown in Fig. H.
• Power the blower on.
• With the tube
5
positioned several inches above the
ground, and using a sweeping motion from side to side,
advance slowly keeping the accumulated debris/leaves
in front of you as shown in Fig.H.
Three‑Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/
support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at
DeWALT Industrial Tool Co., 701East
Joppa Road, Towson, MD 21286or call 1-800-4-
DeWALT
(1-800-433-9258).
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-
DeWALT
(1-800-433-9258) for a freereplacement.
Tool Connect™ Chip (Fig.K)

WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.