User Manual

ManualsBrandsDeWalt ManualsBattery compressorsBattery compressor

ENGLISH

Description of Operation (Fig.A)

Become familiar with these controls before operating theunit.

Auto On(I)/Off(O) Switch

1

: Place this switch in the "AutoOn"

position to provide automatic power to the pressure switch and

"Off" to remove power at the end of eachuse.

Pressure Switch (not shown): The pressure switch

automatically starts the motor when the air tank pressure drops

below the factory set "cut‑in" pressure. It stops the motor when

the air tank pressure reaches the factory set "cut‑out"pressure.

Safety Valve

4

: If the pressure switch does not shut off the

air compressor at its "cut‑out" pressure setting, the safety

valve will protect against high pressure by "popping out" at its

factory set pressure (slightly higher than the pressure switch

"cut‑out"setting).

Tank Pressure Gauge

5

: The tank pressure gauge indicates

the reserve air pressure in thetank.

One-Turn Regulator

6

: Controls the air pressure available at

the quick‑connect outlet. Turn the One‑Turn regulator clockwise

to increase pressure or anti‑clockwise to decrease pressure. Stop

when indicator matches with desired outlet pressure.

Cooling System (not shown): This compressor contains an

advanced design cooling system. At the heart of this cooling

system is an engineered fan. It is perfectly normal for this fan

to blow air through the vent holes in large amounts. You know

that the cooling system is working when air is beingexpelled.

Air Compressor Pump (not shown): Compresses air into the

air tank. Working air is not available until the compressor has

raised the air tank pressure above that required at the airoutlet.

Drain Valve

7

: The drain valve is located at the base of the air

tank and is used to drain condensation at the end of eachuse.

Check Valve

8

: When the air compressor is operating, the

check valve is "open", allowing compressed air to enter the air

tank. When the air compressor reaches "cut‑out" pressure, the

check valve "closes", allowing air pressure to remain inside the

airtank.

Motor Overload Protector (not shown): The motor has

a thermal overload protector. If the motor overheats for

any reason, the overload protector will shut off the motor.

The motor must be allowed to cool down before restarting.

Torestart:

1. Set the Auto On/Off switch to"Off".

2. Remove thebattery.

3. Allow the motor tocool.

4. Replace thebattery.

5. Set the Auto On/Off switch to "Auto On"position.

Quick-Connect Coupler

9

: The Universal EU 1/4" quick

coupling body accepts industrial Push‑to‑Connectplugs.

How to Use Your Unit (Fig.E)

How to Stop



WARNING: When loosening the hose coupling from the

quick‑connect coupler

9

, the coupling piece of the hose

must be held by hand in order to avoid injuries caused by

the recoilinghose.

Know Your Air Compressor

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE

OPERATING YOUR UNIT. Compare the illustrations with your unit

to familiarise yourself with the location of various controls and

adjustments. Save this manual for futurereference.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

Inserting and Removing the Battery Pack

from the Tool (Fig.C, D)

NOTE: Make sure your battery pack

2

is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack

2

with the rails inside the tool’s

handle (Fig. C, D).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

3

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.C, D)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

12

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end‑userapplication.

ASSEMBLY AND ADJUSTMENTS

