User Manual
ENGLISH
3
WARNING: To reduce the risk of injury, read the
instructionmanual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
DCD708 DCD709
Voltage
V
DC
18 18
Type
1 1
Battery type
Li‑Ion Li‑Ion
Power output
W 340 340
No‑load speed
1st gear
2nd gear
min‑1
min‑1
0–450
0–1650
0–450
0–1650
Beats per minute
1st gear
– 0–7650
2nd gear
– 0–28050
Max. Torque (hard/soft)
Nm 65/26 65/26
Chuck capacity
mm 1.5–13 1.5–13
Maximum
drilling
capacity
Wood
Metal
Masonary
mm
mm
mm
30
13
–
30
13
13
Weight (without battery pack)
kg 1.10 1.20
Noise values and vibration values (triax vector sum) according to EN62841‑2‑1:
L
PA
(emission sound pressure
level)
dB(A) 73 88
L
WA
(sound power level) dB(A) 84 99
K (uncertainty for the given
sound level)
dB(A) 3 3
Drilling into metal
Vibration emission value a
h,D
= m/s
2
<2.5 3.0
Uncertainty K = m/s
2
1.5 1.5
Drilling into concrete
Vibration emission value a
h,ID
= m/s
2
– 15.0
Uncertainty K = m/s
2
– 2.9
Screwdriving
Vibration emission value
a
h
=
m/s
2
<2.5 <2.5
Uncertainty K = m/s
2
1.5 1.5
EC‑Declaration of Conformity
Machinery Directive
Tool Connect™ Drill/Driver/Hammerdrille
DCD708, DCD709
DeWALT
declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN60745‑1:2009+A11:2010, EN60745‑2‑1:2010,
EN60745‑2‑2:2010.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact
DeWALT
at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of
DeWALT
.
Markus Rompel
Vice‑President Engineering, PTE‑Europe
DeWALT
, Richard‑Klinger‑Straße 11,
D‑65510, Idstein, Germany
02.11.2018
accessories or poorly maintained, the vibration and/or
noise emission may differ. This may significantly increase
the exposure level over the total workingperiod.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool
is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total workingperiod.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm
(relevant for vibration), organisation of workpatterns.
English (original instructions)
Congratulations!
You have chosen a
DeWALT
tool. Years of experience, thorough
product development and innovation make
DeWALT
one of the
most reliable partners for professional power toolusers.
Technical Data
CORDLESS COMPACT 13mm DRILL/DRIVER/HAMMERDRILL
DCD708, DCD709
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN62841and may be used to
compare one tool with another. It may be used for a preliminary
assessment ofexposure.
WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However
if the tool is used for different applications, with different