User Manual

41
english
NOTE: The torque adjustment collar is only
engaged during screwdriving mode and not in drill
and hammerdrill modes.
Dual Range Gearing (Fig. 1)
The dual range feature of your drill/driver allows you
to shift gears for greater versatility.
1. To select speed 1 (high torque setting), turn
the tool off and permit it to stop. Slide the gear
shifter (d) forward (towards the chuck).
2. To select speed 2 (low torque setting), turn the
tool off and permit it to stop. Slide the gear
shifter back (away from the chuck).
NOTE: Do not change gears when the tool
is running. Always allow the drill to come to a
complete stop before changing gears. If you are
having trouble changing gears, make sure that the
dual range gear shifter is either completely pushed
forward or completely pushed back.
Worklight (Fig. 1)
There is a worklight (e) located on the foot of the
tool. The worklight is activated when the trigger
switch is depressed. When the trigger switch is
released, the worklight will stay illuminated for up to
20 seconds.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Keyless Single Sleeve Chuck
(Fig. 7–9)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck and
turning the tool on. Damage to the chuck
and personal injury may result. Always
lock off trigger switch and disconnect
tool from power source when changing
acces sories.
WARNING: Always ensure the bit
is secure before starting the tool. A
loose bit may eject from tool causing
possible personal injury.
Your tool features a keyless chuck (f) with one
rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory, follow
these steps.
1. Turn tool off and disconnect tool from power
source.
2. Grasp the black sleeve of the chuck with one
hand and use the other hand to secure the
tool. Rotate the sleeve counterclockwise far
enough to accept the desired accessory.
To actuate the fuel gauge, press and hold the fuel
gauge button (l). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Trigger Switch
(Fig.1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop
as soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(Fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and press the forward/reverse control button on
the right side of the tool.
To select reverse, press the forward/reverse control
button on the left side of the tool.
The centre position of the control button locks
the tool in the off position. When changing the
position of the control button, be sure the trigger is
released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Torque Adjustment Collar (Fig. 1)
Your tool has an adjustable torque screwdriver
mechanism for driving and removing a wide array
of fastener shapes and sizes and in some models,
a hammer mechanism for drilling into masonry.
Circling the collar (c) are numbers, a drill bit symbol,
and in some models, a hammer symbol. These
numbers are used to set the clutch to deliver a
torque range. The higher the number on the collar,
the higher the torque and the larger the fastener
which can be driven. To select any of the numbers,
rotate until the desired number aligns with the arrow.