www. .
Dansk (oversat fra original brugsvejledning) 3 Deutsch (übersetzt von den Originalanweisungen) 17 English (original instructions) 33 Español (traducido de las instrucciones originales) 46 Français (traduction de la notice d’instructions originale) 62 Italiano (tradotto dalle istruzioni originali) 77 Nederlands (vertaald vanuit de originele instructies) 92 Norsk (oversatt fra de originale instruksjonene) 107 Português (traduzido das instruções originais) 121 Suomi (käännetty alkuperäisestä
Figure 1 e d f g h c j b m a l j i i k Figure 2 i j o 1
Figure 3 Figure 4 Figure 5 e e f f g g Figure 7 Figure 6 Figure 8 d Figure 9 h n 2
DANSK 13 mm (1/2") TRÅDLØST BOR/SKRUEMASKINE DCD931, DCD980 13 mm (1/2") TRÅDLØST HAMMERBOR/SKRUEMASKINE DCD936, DCD985 Tillykke! Du har valgt et DEWALT-værktøj. Mange års erfaring, ihærdig produktudvikling og innovation gør DEWALT én af de mest pålidelige partnere for professionelle brugere af elværktøj. Tekniske data Spænding Type Batteritype Afgiven effekt Tomgangshastighed 1, gear 2, gear 3, gear Stødhastighed 1, gear 2, gear 3, gear Maks.
DANSK Vibrationsemissionsværdi ah Schrauben ah, = Usikkerhed K = m/s² m/s² < 2,5 1,5 Vibrationsniveauet i dette informationsark er blevet målt i overensstemmelse med en standardiseret test, som er oplyst i EN 60745 og kan bruges til at sammenligne et værktøj med et andet. Det kan bruges til foreløbig vurdering af eksponeringen. ADVARSEL: Det erklærede vibrationsniveau gælder for værktøjets hovedanvendelsesformål.
DANSK EF-konformitetserklæring MASKINDIREKTIV c) DCD931, DCD936, DCD980, DCD985 DEWALT erklærer, at produkterne beskrevet under Tekniske data er udformet i overensstemmelse med: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Disse produkter overholder også direktivet 2004/108/EF og 2011/65/EU. Kontakt DEWALT på følgende adresse for yderligere oplysninger eller se bagsiden af manualen. Undertegnede er ansvarlig for kompilering af den tekniske fil og udsteder denne erklæring på vegne af DEWALT.
DANSK c) d) e) f) g) sikkerhedshjelm eller høreværn, brugt når omstændighederne foreskriver det, reducerer omfanget af personskader. Undgå utilsigtet opstart. Sørg for at der er slukket for kontakten inden værktøjet tilsluttes strømkilde og/eller batterienhed, samles op eller bæres. Når elektrisk værktøj bæres med fingeren på kontakten eller tilsluttes når kontakten er tændt, giver det anledning til ulykker. Fjern eventuelle justerings- eller skruenøgler, før det elektriske værktøj startes.
DANSK Yderligere specifikke sikkerhedsregler for boremaskiner/ skruemaskiner/hammerbor • Brug hørebeskyttelse under slagboring. Støjeksponering kan forårsage høreskader. • Brug de ekstra håndtag, hvis de følger med værktøjet. Manglende kontrol kan medføre personskade. • Hold kun fast i det elektriske værktøj på de isolerede håndtagsflader under udførelse af arbejdet, hvor skæreværktøjet kan berøre skjulte ledninger.
DANSK • Forsøg ALDRIG at oplade batteripakken med andre opladere end dem, der er omtalt i denne manual. Opladeren og batteripakken er specielt designet til at arbejde sammen. • Disse opladere er ikke beregnet til anden brug end opladning af DEWALT genopladelige batterier. Al anden brug kan medføre risiko for brand, elektrisk chok eller livsfarlige elektriske stød. • Udsæt ikke opladeren for regn eller sne. • Træk i stikket i stedet for ledningen, når opladeren frakobles.
DANSK Forsinkelse ved varmt/koldt batteri Når opladeren registrerer et batteri, der er for varmt eller for koldt, starter den automatisk en forsinkelse for varmt/koldt batteri, der suspenderer opladningen, indtil batteriet har nået en passende temperatur. Derefter skifter opladeren automatisk til batteriopladningstilstand. Denne funktion sikrer maksimal batterilevetid.
DANSK Anbefalet opbevaring Oplad kun mellem 4 °C og 40 °C. 1. Det bedste opbevaringssted er køligt og tørt, hvor den ikke udsættes for direkte sollys og ekstrem varme eller kulde. For optimal batteriydelse og -liv skal du opbevare batteripakker ved stuetemperatur, når de ikke er i brug. Tag hensyn til miljøet ved bortskaffelse af batteripakken. 2. For langtids opbevaring anbefales det at opbevare en fuldt opladet batteripakke et køligt, tørt sted uden for opladeren for optimale resultater.
DANSK f. Tilstandskontrolkrave g. Gearvælger h. Sidehåndtag i. Batteripakke J. Batteriudløserknapper k. Bæltekrog l. Monteringsskrue m. Boreclips TILSIGTET BRUG Disse boredrivværk/hammerbor er designet til professionelle boreopgaver, slagboring og skruetrækkeropgaver. MÅ IKKE anvendes under våde forhold eller i nærheden af brændbare væsker eller gasser. Disse bor/skruemaskiner/hammerbor er professionelt værktøj. LAD IKKE børn komme i kontakt med værktøjet.
DANSK BEMÆRK: Vedvarende brug i variabelt hastighedsområde anbefales ikke. Det kan skade kontakten og bør undgås. Sidehåndtag (fig. 1) ADVARSEL:For at reducere risikoen for personskade SKAL DU ALTID betjene værktøjet med sidehåndtaget korrekt monteret. Mangel på at gøre dette kan resultere i, at sidehåndtaget glider under betjening af værktøjet og efterfølgende manglende kontrol. Hold værktøjet med begge hænder for at øge kontrollen.
DANSK BEMÆRK: Skift ikke gear, når værktøjet kører. Lad altid boret standse helt, før du skifter gear. Hvis du har problemer med at skifte gear, skal du sikre dig, at gearvælgeren er indkoblet i én af de tre hastighedsindstillinger. Patroner ADVARSEL: Forsøg ikke at fastgøre bor (eller andet tilbehør) ved at holde fast i den forreste del af patronen og tænde for værktøjet. Det kan medføre personskade samt skade på patronen.
DANSK strømforsyningen, før der foretages justeringer eller afmonteringer/ påmonteringer af dele eller tilbehør. ADVARSEL: For at reducere risikoen for personskade, sørg ALTID for at arbejdsemnet er grundigt forankret eller fastgjort. Hvis der bores i tyndt materiale, anvend en træ “backup” blok for at forhindre, at materialet bliver beskadiget. 1. Vælg den ønskede hastighed/momentområde ved hjælp af gearvælgeren, så den svarer til hastighed og moment for den planlagte brug.
DANSK Rengøring ADVARSEL: Blæs støv og snavs ud af hovedhuset med tør luft, lige så snart der samler sig snavs i og omkring luftaftrækket. Bær godkendte beskyttelsesbriller og godkendt støvmaske ved udførelse af denne procedure. ADVARSEL: Brug aldrig opløsningsmidler eller andre kraftige kemikalier til at rengøre værktøjets ikke-metalliske dele. Disse kemikalier kan svække de materialer, der anvendes i disse dele. Brug en klud, der kun er fugtet med vand og mild sæbe.
DANSK GARANTI DEWALT er sikker på produkternes kvalitet og tilbyder en enestående garanti til professionelle brugere af dette værktøj. Denne garantierklæring er en tilføjelse til dine kontraktmæssige rettigheder som professionel bruger eller dine lovbefalede rettigheder som privat ikkeprofessionel bruger og påvirker dem på ingen måde. Garantien er gyldig inden for medlemsstaterne af Den Europæiske Union og Det Europæiske Frihandelsområde.
DEUTSCH 13 mm (1/2") AKKU-BOHRSCHRAUBER DCD931, DCD980 13 mm (1/2") AKKU-SCHLAGBOHRER/SCHRAUBER DCD936, DCD985 Herzlichen Glückwunsch! Sie haben sich für ein Werkzeug von DEWALT entschieden. Langjährige Erfahrung, sorgfältige Produktentwicklung und Innovation machen DEWALT zu einem zuverlässigen Partner für professionelle Anwender von Elektrowerkzeugen. Technische Daten Spannung Typ Akkutyp Abgabeleistung Leerlaufdrehzahl 1, Gang 2, Gang 3, Gang Schlagfrequenz 1, Gang 2, Gang 3, Gang Max.
DEUTSCH Schwingungsemissionswert ah Schrauben ah, = Unsicherheitswert K = m/s² m/s² < 2,5 1,5 Der in diesem Informationsblatt angegebene Vibrationsemissionsgrad wurde nach Maßgabe eines standardisierten Tests, wie in EN 60745 vorgegeben, gemessen und kann zum Vergleich von Werkzeugen verwendet werden. Er kann zu einer vorläufigen Einschätzung der Exposition verwendet werden.
DEUTSCH EG-Konformitätserklärung MASCHINENRICHTLINIE b) DCD931, DCD936, DCD980, DCD985 DEWALT erklärt hiermit, dass diese unter Technische Daten beschriebenen Produkte die folgenden Vorschriften erfüllen: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Diese Produkte erfüllen auch die Richtlinie 2004/108/EG und 2011/65/EU. Für weitere Informationen wenden Sie sich bitte an DEWALT unter der folgenden Adresse oder schauen Sie auf der Rückseite dieser Betriebsanleitung nach.
DEUTSCH b) c) d) e) f) g) Umgang mit Elektrowerkzeugen gesunden Menschenverstand walten. Benutzen Sie keine Elektrowerkzeuge, wenn Sie müde sind oder unter dem Einfluss von Drogen, Alkohol oder Medikamenten stehen. Ein Moment der Unachtsamkeit beim Gebrauch von Elektrowerkzeugen kann zu ernsthaften Verletzungen führen. Tragen Sie eine persönliche Schutzausrüstung. Tragen Sie stets einen Augenschutz.
DEUTSCH c) d) Halten Sie den nicht benutzten Akku von Metallgegenständen, wie z. B. Büroklammern, Münzen, Schlüsseln, Nägeln, Schrauben oder anderen kleinen Metallgegenständen fern, die eine Überbrückung der Kontakte verursachen könnten. Ein Kurzschluss zwischen den Akkukontakten kann Verbrennungen oder einen Brand hervorrufen. Bei unsachgemäßer Verwendung kann Flüssigkeit aus dem Akku austreten. Vermeiden Sie den Kontakt damit. Bei unbeabsichtigtem Kontakt mit Wasser abspülen.
DEUTSCH • Lesen Sie vor der Verwendung des Ladegeräts alle Anweisungen und Warnhinweise auf dem Ladegerät und dem Akku. WARNUNG: Stromschlaggefahr. Keine Flüssigkeiten in das Ladegerät gelangen lassen. Dies kann einen elektrischen Schlag zur Folge haben. VORSICHT: Verbrennungsgefahr. Zur Reduzierung der Verletzungsgefahr sollten nur Akkus von DEWALT verwendet werden. Andere Akkutypen können sich überhitzen und bersten, was zu Verletzungen und Sachschäden führen kann.
DEUTSCH BEWAHREN SIE DIESE ANWEISUNGEN AUF Temperaturverzögerung Ladegeräte Das Ladegerät DCB105 kann folgende Akkus laden: 10,8 V, 14,4 V und 18 V Li-Ion (DCB121, DCB123, DCB140, DCB141, DCB142, DCB180, DCB181 und DCB182). An diesem Ladegerät müssen keine Einstellungen vorgenommen werden, und es wurde für eine möglichst einfache Bedienung konzipiert. Ladevorgang [Abb. (figure) 2] 1. Stecken Sie das Ladegerät in eine geeignete Steckdose mit 230 V, bevor Sie den Akku einsetzen. 2.
DEUTSCH • Das Werkzeug und den Akku niemals in Bereichen lagern oder verwenden, in denen die Temperatur 40 ºC überschreiten könnte (z. B. Scheunen oder Metallgebäude im Sommer). • Der Inhalt einer geöffneten Akkuzelle kann Atemwegsreizungen verursachen. Sorgen Sie für Frischluft. Wenn die Symptome anhalten, begeben Sie sich in ärztliche Behandlung. WARNUNG: Verbrennungsgefahr. Die Akkuflüssigkeit kann brennbar sein, wenn sie Funken oder einer Flamme ausgesetzt ist.
DEUTSCH x Problem mit Akku oder Ladegerät. Problem mit der Stromversorgung. Nicht mit elektrisch leitenden Gegenständen berühren. Beschädigte Akkus nicht aufladen. HINWEIS: Akkus, Ladegeräte und Transportboxen sind im Lieferumfang von N-Modellen nicht enthalten. • Prüfen Sie das Werkzeug, die Teile oder Zubehörteile auf Beschädigungen, die beim Transport entstanden sein könnten. • Nehmen Sie sich Zeit, diese Betriebsanleitung vor Inbetriebnahme sorgfältig zu lesen und zu verstehen. Beschreibung (Abb.
DEUTSCH Elektrische Sicherheit Der Elektromotor ist nur für eine Netzspannung ausgelegt. Überprüfen Sie daher, ob die Netzspannung der auf dem Typenschild des Ladegeräts angegebenen Spannung entspricht. Vergewissern Sie sich außerdem, dass die Netzspannung Ihres Ladegeräts mit der Ihres Stromnetzes übereinstimmt. Ihr DEWALT-Ladegerät ist gemäß EN 60335 doppelt isoliert und erfordert deshalb keinen Erdleiter.
DEUTSCH Der Zusatzhandgriff (h) wird vor dem Getriebegehäuse festgespannt und kann um 360° gedreht werden, für Rechtshänder oder Linkshänder. Der Zusatzhandgriff muss fest genug angezogen werden, um der Drehbewegung des Werkzeugs bei Festklemmen des Einsatzes zu widerstehen. Prüfen Sie, dass Sie den Zusatzhandgriff am entfernten Ende fassen, um das Werkzeug bei Festklemmen unter Kontrolle zu halten.
DEUTSCH HINWEIS: Ändern Sie nicht den Gang, während das Gerät sich dreht. Lassen Sie den Bohrer immer vollständig zum Stillstand kommen, bevor Sie den Gang wechseln. Bei Problemen beim Gangwechsel prüfen Sie, dass der Gangschalter in einer der drei Gangpositionen eingerastet ist. Riemenhaken und Bitclip (Abb.
DEUTSCH Richtige Haltung der Hände (Abb. 9) WARNUNG: Um die Gefahr schwerer Verletzungen zu mindern, beachten Sie IMMER die richtige Haltung der Hände, wie in Abbildung 9 gezeigt. WARNUNG: Um die Gefahr schwerer Verletzungen zu mindern, halten Sie das Gerät IMMER sicher fest und seien Sie auf eine plötzliche Reaktion gefasst. Die richtige Haltung der Hände bedeutet, dass eine Hand am Hauptgriff (n) liegt, während die andere Hand den seitlichen Griff (h) hält. Bohrbetrieb (Abb.
DEUTSCH 2. Üben Sie beim Bohren nur soviel Kraft auf das Schlagwerk aus, dass es nicht zu sehr springt. Zuviel Kraft verringert die Bohrdrehzahl, führt zur Überhitzung und geringerer Bohrleistung. trockener Druckluft aus dem Gehäuse. Tragen Sie zugelassenen Augenschutz und eine zugelassene Staubmaske, wenn Sie diesen Vorgang durchführen. 3. Bohren Sie gerade, mit dem Bit im rechten Winkel zum Werkstück.
DEUTSCH Die Wiederverwendung von recyceltem Material trägt zur Verhinderung von Umweltverschmutzung und zur Reduzierung des Rohstoffsbedarfs bei. Nach Maßgabe örtlicher Vorschriften ist die getrennte Sammlung von elektrischen Geräten u. U. über Abholung, Sammelstellen oder den Fachhändler möglich, wo das Produkt ursprünglich bezogen wurde. DEWALT betreibt eine Einrichtung zur Sammlung und zum Recycling von ausgedienten DEWALTProdukten.
DEUTSCH GARANTIE DEWALT vertraut auf die Qualität seiner Produkte und bietet daher den professionellen Anwendern des Produktes eine herausragende Garantie. Diese Garantieerklärung gilt als Ergänzung und unbeschadet Ihrer Rechte aus dem Vertrag als professioneller Anwender oder Ihrer gesetzlichen Ansprüche als privater, nichtprofessioneller Anwender. Diese Garantie gilt innerhalb der Staatsgebiete der Mitgliedsstaaten der Europäischen Union und der Europäischen Freihandelszone.
ENGLISH 1/2" (13 mm) CORDLESS DRILL/DRIVER DCD931, DCD980 1/2" (13 mm) CORDLESS HAMMERDRILL/DRIVER DCD936, DCD985 Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical Data Voltage Type Battery Type Power output No-load speed 1st gear 2nd gear 3rd gear Impact rate 1st gear 2nd gear 3rd gear Max.
EN GLI S H Vibration emission value ah Screwdriving ah = Uncertainty K = m/s² m/s² < 2.5 1.5 < 2.5 1.5 WARNING: The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. VDC Ah kg Charger Mains voltage Battery type Approx.
ENGLISH EC-Declaration of Conformity MACHINERY DIRECTIVE DCD931, DCD936, DCD980, DCD985 DEWALT declares that these products described under Technical Data are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. These products also comply with Directive 2004/108/EC and 2011/65/EU. For more information, please contact DEWALT at the following address or refer to the back of the manual.
EN GLI S H e) f) g) wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
ENGLISH hearing loss. Temporary hearing loss or serious ear drum damage may result from high sound levels generated by hammerdrilling. • Wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eye damage. • Hammer bits and tools get hot during operation. Wear gloves when touching them.
EN GLI S H the charger in a position away from any heat source. • Do not operate charger with damaged cord or plug — have them replaced immediately. • Do not operate charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorised service centre. • Do not disassemble the charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
ENGLISH presence of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes. • Never force the battery pack into charger. Do not modify the battery pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious personal injury. • Charge the battery packs only in designated DEWALT chargers. • DO NOT splash or immerse in water or other liquids.
EN GLI S H Do not charge damaged battery packs. Use only with DEWALT battery packs. Others may burst, causing personal injury and damage. Do not expose to water. Description (fig. 1, 2) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. a. Trigger switch b. Forward/reverse control button c. Worklight Have defective cords replaced immediately. d. Chuck Charge only between 4° C and 40° C. g. Gear shifter e. Torque adjustment collar f. Mode control collar h.
ENGLISH Mains Plug Replacement (U.K. & Ireland Only) If a new mains plug needs to be fitted: • Safely dispose of the old plug. • Connect the brown lead to the live terminal in the plug. • Connect the blue lead to the neutral terminal. WARNING: No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3 A. Using an Extension Cable An extension cord should not be used unless absolutely necessary.
EN GLI S H The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released. NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem. Worklight (fig. 1) There is a worklight (c) located just above the trigger switch (a). The worklight will be activated when the trigger switch is squeezed.
ENGLISH To release the accessory, repeat Steps 1 and 2 above. Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for maximum tightness. Belt Hook and Bit Clip (fig. 1) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook.
EN GLI S H NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The lower the number, the lower the torque output. 2. Rotate the mode control collar (f) so the screw symbol is aligned with the arrow. 3. Reset the torque adjustment collar (e) to the appropriate number setting for the torque desired. Make a few practice runs in scrap or unseen areas to determine the proper position of the torque adjustment collar.
ENGLISH Should you find one day that your DEWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
ESPAÑOL TALADRO PERCUTOR INALÁMBRICO 13 mm (1/2") DCD931, DCD980 MARTILLO PERCUTOR INALÁMBRICO 13 mm (1/2") DCD936, DCD985 ¡Enhorabuena! Ha elegido una herramienta DEWALT. Años de experiencia, innovación y un exhaustivo desarrollo de productos hacen que DEWALT sea una de las empresas más fiables para los usuarios de herramientas profesionales.
ESPAÑOL Valor de la emisión de vibración ah Taladrado de impacto ah,ID = Incertidumbre K = Valor de la emisión de vibración ah Atornillado ah = Incertidumbre K = m/s² m/s² – – 11,0 1,5 – – 11,0 1,5 m/s² m/s² < 2,5 1,5 < 2,5 1,5 < 2,5 1,5 < 2,5 1,5 El nivel de emisión de vibración que se ofrece en esta hoja informativa se ha medido de acuerdo con la prueba estandarizada que ofrece la norma EN 60745 y puede utilizarse para comparar una herramienta con otra.
ESPAÑOL Indica riesgo de descarga eléctrica. Indica riesgo de incendio. Declaración de conformidad CE DIRECTRIZ DE LA MAQUINARIA DCD931, DCD936, DCD980, DCD985 DEWALT declara que los productos descritos bajo Datos técnicos son conformes a las normas: 2006/42/EG, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Estos productos son conformes también a la Directriz 2004/108/CE y 2011/65/UE.
ESPAÑOL b) c) d) e) f) g) No utilice una herramienta eléctrica si está cansado o bajo el efecto de drogas, alcohol o medicamentos. Un momento de descuido mientras se opera una herramienta eléctrica puede provocar lesiones personales graves. Utilice equipo de seguridad personal. Utilice siempre protección ocular. El uso de equipo de seguridad, como mascarillas para polvo, calzado de seguridad antideslizante, cascos o protección auditiva en las condiciones adecuadas reducirá las lesiones personales.
ESPAÑOL c) d) paquete de baterías puede producir riesgo de lesiones e incendio. Cuando no utilice el paquete de baterías, manténgalo lejos de otros objetos metálicos como sujetapapeles, monedas, llaves, clavos, tornillos u otros objetos metálicos pequeños que puedan realizar una conexión desde un terminal al otro. Los cortocircuitos en los terminales de la batería pueden provocar quemaduras o incendio. En condiciones abusivas, puede salir expulsado líquido de la batería. Evite el contacto con él.
ESPAÑOL Instrucciones de seguridad importantes para todos los cargadores de batería GUARDE LAS PRESENTES INSTRUCCIONES: Este manual incluye instrucciones importantes de seguridad y funcionamiento para el cargador de pilas DCB105. • Antes de utilizar el cargador, lea todas las instrucciones y advertencias del cargador, del paquete de baterías y del producto que utiliza el paquete de baterías. ADVERTENCIA: Peligro de electrocuciones. No permita que ningún líquido penetre en el cargador.
ESPAÑOL GUARDE LAS PRESENTES INSTRUCCIONES Si el cargador indica un problema, lleve el cargador y el paquete de pilas a un centro de reparación autorizado para que los pruebe. Cargadores El cargador DCB105 acepta los paquetes de pilas de 10,8 V, 14,4 V y 18 V de litio-ión (DCB121, DCB123, DCB140, DCB141, DCB142, DCB180, DCB181 y DCB182). Este cargador no necesita ningún ajuste y está diseñado para ofrecer el funcionamiento más fácil al usuario. Procedimiento de carga (fig. 2) 1.
ESPAÑOL • NO salpique ni sumerja en agua ni en otros líquidos. • No guarde ni utilice la herramienta y el paquete de baterías en lugares en los que la temperatura pueda alcanzar o superar los 40 ºC (105 ºF) (como por ejemplo, en los cobertizos de exterior o en las instalaciones metálicas en verano). • Para obtener mejores resultados, compruebe que el paquete de pilas está completamente cargado antes de utilizarlo. ADVERTENCIA: No intente nunca abrir el paquete de baterías por ningún motivo.
ESPAÑOL Problema en la línea de alimentación. No realizar pruebas con objetos conductores. No cargar baterías deterioradas. Usar sólo baterías DEWALT, cualquier otra puede estallar y provocar lesiones corporales y daños materiales. No exponer al agua. NOTA: Los paquetes de pilas, los cargadores y las cajas no están incluidos en los modelos N. • Compruebe si la herramienta, piezas o accesorios han sufrido algún desperfecto durante el transporte.
ESPAÑOL Seguridad eléctrica El motor eléctrico se ha diseñado para funcionar con un único voltaje. Verifique siempre que el voltaje de las baterías coincida con el voltaje que figura en la placa de especificaciones. Asegúrese también de que el voltaje del cargador coincida con el de la red eléctrica. El cargador DEWALT tiene doble aislamiento de acuerdo con la norma EN 60335; por lo que no se necesita un conductor de tierra.
ESPAÑOL Si el modelo no está equipado con un asa lateral, sostenga el taladro con una mano en el asa y otra mano en la batería. NOTA: La abrazadera de ajuste de par motor (e) puede fijarse en cualquier número. NOTA: El asa lateral viene en todos los modelos. Gire la abrazadera de control de modo (f) de modo que el símbolo del tornillo se alinee con la flecha. Botón de control adelante/atrás (fig.
ESPAÑOL Portabrocas ADVERTENCIA: No intente apretar las brocas de taladro ( ni ningún otro accesorio) agarrando la parte delantera del portabrocas y encendiendo la herramienta. Puede producirse daño al portabrocas y lesiones personales. Cuando cambie accesorios, siempre apague el interruptor de puesta en marcha, desconecte la herramienta de la fuente de suministro eléctrico. ADVERTENCIA: Asegúrese siempre de que la broca esté bien puesta antes de poner en funcionamiento la herramienta.
ESPAÑOL Para tener una posición adecuada de las manos, ponga una mano en la empuñadura principal (n) y la otra en la empuñadura lateral (h). Funcionamiento del taladro (fig. 3) ADVERTENCIA: Para reducir el riesgo de lesiones personales graves, apague la herramienta y desconecte la herramienta de la corriente antes de realizar ajustes o desmontar/instalar los acoples o accesorios.
ESPAÑOL 4. Cuando taladre agujeros profundos, si la velocidad del martillo comienza a disminuir, retire la broca parcialmente del orificio con la herramienta en funcionamiento para limpiar el polvo del agujero. 5. Para mampostería, utilice brocas de punta de carburo o de mampostería. Un flujo uniforme y suave de polvo indica la tasa de taladrado adecuada. MANTENIMIENTO Su herramienta eléctrica DEWALT ha sido diseñada para funcionar mucho tiempo con un mínimo de mantenimiento.
ESPAÑOL Puede comprobar dónde se encuentra su agente de reparaciones más cercano contactando con la oficina DEWALT de su zona en la dirección indicada en este manual. También puede obtener una lista de agentes de reparaciones autorizados de DEWALT y todos los detalles de nuestro servicio después de la venta en Internet en www.2helpU.com. Batería recargable Esta batería de larga duración debe recargarse cuando deje de producir la suficiente potencia en trabajos que se realizaban con facilidad anteriormente.
ESPAÑOL GARANTÍA DEWALT tiene plena confianza en la calidad de sus productos y ofrece una excepcional garantía para los usuarios profesionales del producto. Esta declaración de garantía es adicional a sus derechos contractuales como usuario profesional y a sus derechos legales como usuario particular no profesional y no perjudica de ningún modo dichos derechos. La garantía es válida dentro de los territorios de los Estados Miembros de la Unión Europea y del Área de Libre Comercio Europea.
FRANÇAIS PERCEUSE/VISSEUSE SANS FIL 13 mm (1/2") DCD931, DCD980 MARTEAU-PERFORATEUR/VISSEUSE SANS FIL 13 mm (1/2") DCD936, DCD985 Félicitations ! Vous avez choisi un outil DEWALT. Des années d’expertise dans le développement et l’innovation de ses produits ont fait de DEWALT, le partenaire privilégié des utilisateurs professionnels d’outils électriques.
FRANÇAIS Valeur d’émission de vibration ah Vissage ah = m/s² Incertidumbre K = m/s² < 2,5 1,5 AVERTISSEMENT : le niveau d’émission vibratoire déclaré correspond aux applications principales de l’outil. Néanmoins, si l’outil est utilisé pour différentes applications ou mal entretenu, l’émission vibratoire peut varier. Ces éléments peuvent considérablement augmenter le niveau d’exposition sur la période totale de travail.
FRANÇAIS Déclaration de conformité CE DIRECTIVES MACHINES DCD931, DCD936, DCD980, DCD985 DEWALT certifie que les produits décrits dans le paragraphe Fiche technique sont conformes aux normes : 2006/42/CE, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Ces produits sont également conformes aux normes 2004/108/CE et 2011/65/UE. Pour plus d’informations, veuillez contacter DEWALT à l’adresse suivante ou vous reporter au dos de cette notice d’instructions.
FRANÇAIS b) c) d) e) f) g) utilisez un outil électrique. N’utilisez pas un outil électrique si vous êtes fatigué ou sous l’influence de drogues, d’alcool ou de médicaments. Un moment d’inattention durant l’utilisation d’un outil électrique peut entraîner de graves blessures corporelles. Utilisez un équipement de sécurité individuelle. Portez toujours des lunettes de sécurité.
FRANÇAIS d) circuiter les bornes entre elles peut provoquer des brûlures ou un incendie. Dans des conditions abusives, du liquide peut s’échapper de la pile ; en éviter le contact. En cas de contact accidentel, rincez à l’eau. Si le liquide entre en contact avec les yeux, consultez également un médecin. Le liquide qui s’échappe de la pile peut engendrer une irritation ou des brûlures.
FRANÇAIS sur le chargeur, le bloc batterie et le produit utilisant le bloc batterie. AVERTISSEMENT : risque de choc. Ne pas laisser les liquides pénétrer dans le chargeur. Risque de choc électrique. ATTENTION : risque de brûlure. Pour réduire le risque de blessures, ne charger que des blocs batteries rechargeables DEWALT. Tout autre type de batterie peut surchauffer et exploser, entraînant des blessures et des dégâts matériels. Ne pas recharger les batteries non rechargeables.
FRANÇAIS Procédure de charge (fig. 2) 1. Branchez le chargeur dans une prise 230 V appropriée avant d’insérer le bloc batterie. 2. Insérez le bloc batterie (i) dans le chargeur en prenant soin que le bloc sont complètement inséré dans le chargeur. Le témoin rouge (charge) clignote en continu pour indiquer que le processus de charge a commencé. 3. Lorsque le voyant rouge RESTE ALLUMÉ en continu, il indique que la charge est terminée.
FRANÇAIS pas l’insérer dans un chargeur Ne pas écraser, laisser tomber, ou endommager le bloc batterie. Ne pas utiliser un bloc batterie ou un chargeur ayant reçu un choc violent, étant tombé, ayant été écrasé ou endommagé de quelque façon que ce soit (par ex. percé par un clou, frappé d’un coup de marteau, piétiné). Risque de choc électrique ou d’électrocution. Les blocs batterie endommagés doivent être renvoyés à un centre de réparation pour y être recyclés.
FRANÇAIS Remplacer systématiquement tout cordon endommagé. a. Gâchette b. Bouton de contrôle vissage/dévissage c. Eclairage Recharger seulement entre 4 °C and 40 °C. d. Mandrin Mettre la batterie au rebut conformément à la réglementation en matière d’environnement. g. Bouton de changement vitesse e. Bague de réglage de couple f. Bague de réglage de mode h. Poignée latérale i. Batterie Ne jetez pas le bloc batterie au feu. j. Boutons de déverrouillage de la batterie k. Crochet pour courroie l.
FRANÇAIS Type 11 pour la classe II (Isolation double) -outils Type 12 pour la classe I (Conducteur de terre) - outils CH En cas d’utilisation à l’extérieur, connecter les outils portatifs à un disjoncteur FI. Utilisation d’une rallonge N’utilisez une rallonge qu’en cas de nécessité absolue. Utilisez une rallonge homologuée adaptée à la puissance absorbée de votre chargeur (consultez les Fiche technique). Le calibre minimum du conducteur est de 1 mm2 et la longueur maximum de 30 m.
FRANÇAIS Bouton de marche avant/arrière (fig. 1) Le bouton de marche avant/arrière (b) détermine le sens de rotation de l’outil et sert aussi de bouton de verrouillage. Pour choisir la marche avant, dégagez la gâchette et appuyez sur le bouton de marche avant/arrière sur le côté droit de l’outil. numéro. Cependant, la bague de réglage de couple est seulement activée en mode de vissage et non pas dans les modes de perçage ou de marteauperforateur. MARTELAGE-PERFORAGE (FIG.
FRANÇAIS AVERTISSEMENT : s’assurer systématiquement que la mèche est bien arrimée avant de démarrer l’outil. Une mèche desserrée pourrait être éjectée de l’outil et poser des risques de dommages corporels. MANDRIN AUTOMATIQUE À MANCHON SIMPLE (FIG. 6–8) Votre outil est équipé d’un mandrin automatique à manchon rotatif pour utiliser le mandrin à une main. Pour insérer une mèche, ou tout autre accessoire, suivez la procédure ci-après : 1. Verrouillez la gâchette en position d’ARRÊT.
FRANÇAIS solidement. Si le matériau à percer est mince, appuyez-le sur un bloc de bois pour éviter d’endommager le matériau. 1. Sélectionnez la vitesse/le couple désiré à l’aide du changeur de vitesse pour assortir la vitesse et le couple à l’opération désirée. Réglez la bague de réglage de mode sur le symbole perceuse. 2. Pour le BOIS, utilisez : mèche hélicoïdale, foret à trois pointes, mèche torsadée ou emporte-pièce. Pour le MÉTAL, utilisez : mèche hélicoïdale en acier ou emporte-pièce.
FRANÇAIS Protection de l’environnement Lubrification Votre outil électrique ne requiert aucune lubrification additionnelle. Entretien AVERTISSEMENT : éliminer poussière et saleté du boîtier principal à l’aide d’air comprimé chaque fois que les orifices d’aération semblent s’encrasser. Porter systématiquement des lunettes de protection et un masque anti-poussières homologués au cours de cette procédure.
FRANÇAIS GARANTIE DEWALT est si sûr de la qualité de ses produits qu’il propose à tous les professionnels qui les utilisent, une garantie exceptionnelle. Cette promesse de garantie s’ajoute à vos droits contractuels en tant qu’utilisateur professionnel ou vos droits légaux en tant qu’utilisateur privé, non professionnel, et elle ne peut en aucun cas leur porter préjudices.
ITALIANO TRAPANO/AVVITATORE A BATTERIA DA 13 mm (1/2") DCD931, DCD980 TRAPANO/AVVITATORE A PERCUSSIONE A BATTERIA DA 13 mm (1/2") DCD936, DCD985 Congratulazioni! Per aver scelto un apparato DEWALT. Gli anni di esperienza, lo sviluppo e l’innovazione del prodotto fanno di DEWALT uno dei partner più affidabili per gli utilizzatori di apparati elettrici professionali.
ITALIANO Valore di emissione delle vibrazioni ah Avvitatura ah = m/s² Incertezza K = m/s² < 2,5 1,5 Il livello di emissione di vibrazioni indicato in questo foglio informativo è stato misurato con un test standard fornito in EN 60745 e può essere utilizzato per confrontare utensili fra di loro. Può essere utilizzato per una valutazione preliminare dell’esposizione. AVVERTENZA: il livello di emissioni delle vibrazioni dichiarato rappresenta le applicazioni principali dell’utensile.
ITALIANO Dichiarazione di conformità CE DIRETTIVA MACCHINE c) DCD931, DCD936, DCD980, DCD985 DEWALT dichiara che i prodotti qui descritti nei Dati tecnici sono conformi alle normative: 2006/42/CE, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Questi prodotti sono anche conformi alle normative 2004/108/CE e 2011/65/UE. Per ulteriori informazioni, contattare DEWALT all’indirizzo seguente o vedere sul retro del manuale.
ITALIANO c) d) e) f) g) mascherine per la polvere, scarpe antiscivolo, elmetti o cuffie protettive, in condizioni opportune consente di ridurre le lesioni personali. Evitare la messa in funzione non intenzionale. Assicurarsi che l’interruttore sia in posizione off prima di connettere la fonte di corrente e/o il blocco batteria e prima di afferrare o trasportare l’utensile.
ITALIANO 6) RIPARAZIONI a) L’elettroutensile deve essere riparato da personale qualificato, utilizzando parti di ricambio identiche. In questo modo viene garantita la sicurezza dell’elettroutensile. Norme di sicurezza aggiuntive specifiche per trapani/avvitatori/ trapani a percussione • Indossare le protezioni acustiche durante l’utilizzo. L’esposizione al rumore può causare danni all’udito. • Utilizzare le impugnature ausiliarie, se fornite con l’utensile.
ITALIANO AVVISO: in certe condizioni, con il caricabatterie inserito nella presa elettrica, il caricabatterie può essere cortocircuitato da corpi estranei. Materiali estranei di natura conduttiva come, a titolo esemplificativo ma non esaustivo, polvere di smerigliatura, schegge metalliche, lana di acciaio, lamine di alluminio o qualsiasi accumulo di particelle metalliche, dovrebbero essere eliminati dalle cavità del caricabatterie.
ITALIANO Procedura di carica Vedere la tavola seguente per lo stato di carica del pacco batteria. Stato di carica x in carica –– carica completa ––––––––––––––––– ritardo per pacco caldo/freddo pacco batteria o caricabatteria difettoso problema con la linea di alimentazione –– –– –– –– • –– • –– • –– • •••••••••••• •• •• •• •• •• •• Questo caricabatteria non caricherà un pacco batteria difettoso.
ITALIANO ATTENZIONE: quando non viene usato, appoggiare l’apparato di fianco su una superficie stabile, dove non ci sia rischio di inciampare o di cadere. Alcuni apparati con pacchi batterie grandi possono rimanere in piedi poggiando sul pacco batteria ma potrebbero cadere facilmente. ISTRUZIONI DI SICUREZZA SPECIFICHE PER IONI DI LITIO (Li-Ion) • Non bruciare il pacco batteria anche se è seriamente danneggiato o è completamente esausto. Il pacco batteria può esplodere se gettato nel fuoco.
ITALIANO j. Pulsanti di rilascio della batteria Non bruciare il pacco batteria. k. Gancio a nastro l. Vite di montaggio Carica i pacchi batteria Li-Ion. Vedere i Dati tecnici per il tempo di ricarica. Solo per uso interno. m. Ferma punta UTILIZZO PREVISTO Questi trapani avvitatori/trapani a percussione sono progettati per applicazioni professionali di trapanatura, trapanatura a percussione e avvitamento.
ITALIANO Uso di una prolunga È preferibile non utilizzare una prolunga, tranne nei casi in cui sia assolutamente necessario. Utilizzare una prolunga approvata, adatta per la tensione in ingresso del caricabatteria (vedere i Dati tecnici). La dimensione minima del conduttore è 1 mm2; la lunghezza massima è 30 m. Se si utilizza un avvolgitore, estrarre il cavo per l’intera lunghezza. MONTAGGIO E REGOLAZIONI AVVERTENZA: prima di effettuare montaggio e regolazioni, rimuovere sempre il blocco batteria.
ITALIANO Per selezionare la rotazione inversa, rilasciare l’interruttore a grilletto e premere il pulsante di avvitamento/svitamento sul lato destro dell’utensile. La posizione centrale del pulsante di controllo blocca l’utensile in posizione spenta. Quando si modifica la posizione del pulsante di controllo assicurarsi di aver rilasciato il grilletto. NOTA: La prima volta che l’utensile viene messo in moto dopo un cambio della direzione di rotazione, è possibile sentire uno scatto al momento dell’avvio.
ITALIANO MANDRINO AUTOSERRANTE A MANICOTTO SINGOLO (FIG. 6–8) L’utensile è dotato di un mandrino autoserrante con un manicotto rotante per poter azionare con una sola mano il mandrino. Per inserire un’altra punta o un accessorio, seguire le istruzioni seguenti. 1. Bloccare il grilletto in posizione OFF. Spegnere e scollegare l’utensile dall’alimentazione. 2. Afferrare il manicotto nero del mandrino (d) con una mano servendosi dell’altra per sistemare l’utensile come illustrato in Figura 6.
ITALIANO piccolo spessore utilizzare un blocco di legno come supporto per evitare di danneggiare il materiale. 1. Selezionare la combinazione velocità/coppia desiderata utilizzando il selettore delle marce per adattare velocità e coppia all’operazione da eseguire. Impostare la ghiera di controllo modalità sul simbolo trapano. 2. Per il LEGNO, utilizzare punte elicoidali, a lancia, a trivella o seghe a tazza. Per il METALLO, utilizzare punte elicoidali in acciaio rapido o seghe a tazza.
ITALIANO Il caricabatteria e il pacco batteria non sono parti riparabili. Non vi sono parti riparabili all’interno. Rivolgersi al proprio rivenditore per ulteriori informazioni sugli accessori più adatti. Rispetto ambientale Lubrificazione L’apparato non richiede alcuna ulteriore lubrificazione. Pulizia AVVERTENZA: soffiare via la polvere dall’alloggiamento con aria compressa, non appena vi sia sporco visibile all’interno e intorno alle prese d’aria di ventilazione.
ITALIANO GARANZIA DEWALT realizza prodotti di qualità e offre una garanzia eccezionale per i professionisti che utilizzano i suoi apparati. Questa dichiarazione di garanzia è aggiuntiva e non pregiudica in alcun modo la copertura assicurativa dell’utilizzatore professionista o quella della previdenza sociale per l’utente privato non professionista. La garanzia è valida sui territori degli stati membri dell’Unione Europea o dell’EFTA (Associazione europea di libero scambio).
NEDERLANDS 13 mm (1/2") DRAADLOZE BOOR/DRIL DCD931, DCD980 13 mm (1/2") DRAADLOZE KLOPBOOR/DRIL DCD936, DCD985 Hartelijk gefeliciteerd! U hebt gekozen voor een DEWALT gereedschap. Jarenlange ervaring, grondige productontwikkeling en innovatie maken DEWALT tot een van de betrouwbaarste partners voor gebruikers van professioneel gereedschap.
NEDERLANDS Vibratie-emissiewaarde ah Schroef indraaien ah = Onzekerheid K = m/s² m/s² < 2,5 1,5 < 2,5 1,5 WAARSCHUWING: Het aangegeven trillingsemissieniveau vertegenwoordigt de belangrijkste toepassingen van het gereedschap. Maar als het gereedschap wordt gebruikt voor andere toepassingen, met verschillende accessoires of als het niet goed wordt onderhouden, dan kan de trillingsemissie verschillend zijn. Dit kan het blootstellingsniveau aanzienlijk verhogen over de hele werkperiode.
NEDERLANDS EG-conformiteitsverklaring RICHTLIJN VOOR MACHINES DCD931, DCD936, DCD980, DCD985 DEWALT verklaart dat deze producten zoals beschreven onder Technische gegevens in overeenstemming zijn met: 2006/42/EG; EN 60745-1; EN 60745-2-1; EN 60745-2-2. Deze producten voldoen ook aan Richtlijn 2004/108/EG en 2011/65/EU. Neem voor meer informatie contact op met DEWALT via het volgende adres of kijk op de achterzijde van de gebruiksaanwijzing.
NEDERLANDS 3) PERSOONLIJKE VEILIGHEID a) Blijf alert, kijk naar wat u doet en gebruik uw gezond verstand als u elektrische werktuigen gebruikt. Gebruik geen elektrische werktuigen als u moe of onder de invloed van drugs, alcohol of medicijnen bent. Een moment van onoplettendheid tijdens het gebruik van een elektrisch werktuig kan leiden tot ernstig letsel. b) Gebruik een beschermende uitrusting. Draag altijd oogbescherming.
NEDERLANDS c) d) Wanneer de accu niet wordt gebruikt, houd die dan uit de buurt van andere metalen voorwerpen, zoals paperclips, munten, sleutels, spijkers, schroeven of andere kleine metalen voorwerpen die een verbinding kunnen maken van de ene pool naar de andere.Het kortsluiten van de polen van de batterij kan leiden tot brandwonden of brand. Wanneer de accu onjuist wordt gebruikt, kan vloeistof uit de accu weglekken. Vermijd contact met deze vloeistof.
NEDERLANDS Belangrijke veiligheidsinstructies voor alle acculaders BEWAAR DEZE INSTRUCTIES: Deze handleiding bevat belangrijke instructies voor de veiligheid en voor de bediening van de DCB105-acculader. • Lees voordat u de lader gebruikt, alle instructies en aanwijzingen voor de veiligheid op de lader, de accu en het product dat de accu gebruikt. WAARSCHUWING: Gevaar voor elektrische schok. Laat geen vloeistof in de lader dringen. Dit zou kunnen leiden tot een elektrische schok.
NEDERLANDS Laders De DCB105 lader is geschikt voor Li-Ion-accu’s van 10,8 V, 14,4 V en 18 V (DCB121, DCB123, DCB140, DCB141, DCB142, DCB180, DCB181 and DCB182). Deze lader hoeft niet te worden afgeregeld en is zo ontworpen dat hij zeer gemakkelijk in het gebruik is. Oplaadprocedure (afb. [figure] 2) 1. Steek de lader in een geschikt 230 V-stopcontact voordat u de accu plaats. 2. Plaats de accu (i) in de lader, en let er daarbij op dat de accu geheel in de lader komt te zitten.
NEDERLANDS WAARSCHUWING: Probeer nooit om welke reden dan ook de accu te openen. Als de behuizing van de accu is gescheurd of beschadigd, zet de accu dan niet in de lader. Klem een accu niet vast, laat een accu niet vallen, beschadig een accu niet. Gebruik een accu of lader waar hard op is geslagen, die is gevallen, waar overheen is gereden of die op welke manier dan ook is beschadigd (dat wil zeggen, doorboord met een spijker, geraakt met een hamer, vertrapt) niet.
NEDERLANDS a. Variabele snelheidsschakelaar Niet blootstellen aan water. b. Vooruit/achteruit-regelknop Zorg dat defecte snoeren onmiddellijk worden vervangen. d. Boorklauw c. Werklicht e. Stelring om torsie aan te passen Uitsluitend opladen tussen 4 ºC en 40 ºC. f. Kraag modusbeheer g. Versnellingschakelaar Bied de accu als chemisch afval aan en houd rekening met het milieu. h. Zijgreep i. Accu j. Knoppen accuvrijgave Gooi de accu niet in het vuur. Laad Li-Ion accu‘s op.
NEDERLANDS Een verlengsnoer gebruiken Gebruik geen verlengsnoer, tenzij absoluut noodzakelijk. Gebruik een goedgekeurd verlengsnoer dat geschikt is voor de stroomtoevoer van uw lader (zie Technische gegevens). De minimumafmeting van de geleider is 1 mm2; de maximumlengte is 30 m. Wanneer het verlengsnoer op een haspel zit, rol het snoer dan helemaal af. MONTAGE EN AANPASSINGEN WAARSCHUWING: vóór montage en aanpassing moet u altijd de accu verwijderen.
NEDERLANDS Om achteruit draaien te kiezen laat u de trekkerschakelaar los en drukt u de vooruit/achteruit knop aan de linkerkant van het gereedschap in. De middenpositie van de controleknop vergrendelt het gereedschap in de ‘uit’ stand. Zorg ervoor dat u de trekker loslaat als u de stand van de controleknop wijzigt. OPMERKING: De eerste keer als het gereedschap draait nadat de draairichting is gewijzigd, hoort u misschien een klik bij het opstarten. Dit is normaal en betekent niet dat er een probleem is.
NEDERLANDS SLEUTELLOZE ENKELVOUDIGE HULS BOORHOUDER (AFB. 6–8) Uw gereedschap is voorzien van een sleutelloze boorhouder met een roterende huls voor bediening met één hand van de boorhouder. Om een boorstuik of een ander accessoire te plaatsen, volgt u de onderstaande stappen op. 1. Vergrendel de trekker in de positie OFF. Zet het gereedschap uit en sluit het af van de stroombron. 2.
NEDERLANDS 1. Kies het gewenste snelheid/torsie bereik met de versnellingswisselaar zodat de snelheid en torsie aan de geplande actie voldoen. Stel de kraag modusbeheer op het boorpictogram in. 2. Voor HOUT gebruikt u spiraalboren, steekboren, grondboren of zaagboren. Voor METAAL gebruikt u hoge snelheid spiraalboren of zaagboren. Gebruik een smeermiddel als u metaal boort. De uitzonderingen hierop zijn gietijzer en koper, die droog dienen te worden geboord. 3.
NEDERLANDS Milieubescherming Aparte inzameling. Dit product mag niet bij het normale huishoudafval worden gegooid. Smering Uw elektrisch gereedschap behoeft geen extra smering. Als u op een dag merkt dat uw DEWALT product vervangen moet worden of dat u het verder niet kunt gebruiken, gooi het dan niet bij het huishoudafval. Dit product moet afzonderlijk ingezameld worden.
NEDERLANDS GARANTIE DEWALT vertrouwt op de kwaliteit van zijn producten en biedt professionele gebruikers van het product een uitstekende garantie. Deze garantieverklaring is een aanvulling op uw contractuele rechten als een professionele gebruiker of uw wettelijke rechten als een particuliere, niet-professionele gebruiker, en is op geen enkele wijze van invloed op deze rechten. De garantie is geldig binnen het grondgebied van de Lidstaten van de Europese Unie en de Europese Vrijhandelszone.
NORSK 13 mm (1/2") BATTERIDRILL/BORMASKIN DCD931, DCD980 13 mm (1/2") BATTERIDREVET BORHAMMER/BORMASKIN DCD936, DCD985 Gratulerer! Du har valgt et DEWALT-verktøy. Års erfaring gjennom produktutvikling og innovasjon gjør DEWALT til en av de mest pålitelige partene for profesjonelle brukere av elektrisk verktøy. Tekniske data Spenning Type r Batteritype Utgangseffekt Ubelastet hastighet 1. gir 2. gir 3. gir Slaghastighet 1. gir 2. gir 3. gir Maks.
NORSK Vibrasjonsutslippsverdi ah Bruke som skrutrekker: ah = Usikkerhet K = m/s² m/s² < 2,5 1,5 < 2,5 1,5 < 2,5 1,5 En vurdering av eksponeringsnivået til vibrasjoner bør også tas i betraktning når verktøyet er slått av, eller når det sviver men ikke utfører arbeid. Dette kan redusere eksponeringsnivået vesentlig over hele arbeidsperioden.
NORSK Overensstemmelseserklæring med EU b) MASKINERIDIREKTIV c) DCD931, DCD936, DCD980, DCD985 DEWALT erklærer at de produktene som er beskrevet under Tekniske data er i samsvar med: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Disse produktene er også i samsvar med direktiv 2004/108/EU og 2011/65/EU. For mer informasjon, vennligst kontakt DEWALT på følgende adresser eller se baksiden av håndboken.
NORSK d) e) f) g) eller setter støpselet i stikkontakten mens bryteren er på, øker du faren for ulykker. Fjern eventuelle justeringsnøkler før du slår på det elektriske verktøyet. En skrunøkkel som er festet til en roterende del i det elektriske verktøyet, kan forårsake personskade. Strekk deg ikke for langt. Behold fotfestet og god balanse til enhver tid. Dette gir bedre kontroll over det elektriske verktøyet hvis det skulle oppstå en uventet situasjon. Kle deg skikkelig.
NORSK • Bruk klemmer eller en annen praktisk metode for å feste og støtte arbeidsstykket til en stabil plattform. Det er ikke stabilt nok å holde arbeidsstykket med hånden eller mot kroppen din. Dette kan føre til at du mister styringen. • Bruk hørselsvern hvis du bruker maskinen over lengre tid. Langvarig eksponering mot høyintensiv støy kan føre til hørselstap. Det høye lydnivået fra hammerboring kan føre til midlertidig hørselstap eller alvorlig skade på trommehinnen.
NORSK • Ved bruk av en lader utendørs, sørg alltid for tørr plassering og bruk en skjøteledning som passer for utendørs bruk. Bruk av en skjøteledning beregnet for utendørs bruk reduserer risikoen for elektrisk støt. • Ikke blokker ventilasjonsåpningene på laderen. Ventilasjonsåpningene er plassert på toppen og sidene av laderen. Plasser laderen et sted unna varmekilder. MERK: For å sikre maksimum ytelse og levetid på Li-Ion batterier, lad batteriet helt opp før første gangs bruk.
NORSK • Ikke lad eller bruk batteripakken i eksplosive omgivelser, slik som i nærheten av brennbare væsker, gasser eller støv. Innsetting eller uttak av batteripakken kan antenne støvet eller gassen. • Tving aldri batteripakken inn i laderen. Ikke modifiser batteripakken på noen måte for å passe inn i en ikke-kompatibel lader idet batteripakken kan sprekke og forårsake alvorlig personskade. • Lad batteripakkene kun i egnede DEWALT ladere. • IKKE sprut på eller senke ned i vann eller andre væsker.
NORSK Ikke undersøk med strømførende gjenstander. Beskrivelse (fig. 1, 2) ADVARSEL: Aldri modifiser elektroverktøyet eller noen del av det. Dette kan føre til materiell- eller personskader. Ikke lad skadede batteripakker. a. Utløserbryter Bruk bare DEWALT batteripakker, andre kan sprekke og forårsake personskader og skader på materiell. b. Fremover/bakover kontrollknapp Ikke utsett for vann. d. Chuck c. Arbeidslys e. Momentjusteringskrage Få byttet defekte ledninger omgående. f. Modusvelgerkrage g.
NORSK Bruk av skjøteledning Bryter for variabel hastighet (fig. 1) Skjøteledning bør ikke brukes hvis det ikke er absolutt nødvendig. Bruk en godkjent skjøteledning som egner seg for kraftforsyningen til din lader (se Tekniske data). Minimum størrelse på lederen er 1 mm2; maksimum lengde er 30 m. For å slå på verktøyet, klem på utløserbryteren (a). For å slå av verktøyet, slipp utløserbryteren. Verktøyet er utstyrt med en bremse. Chucken vil stoppe straks utløserbryteren er helt ute.
NORSK MERK: Arbeidslampen er beregnet på belysning av den nærmeste arbeidsflaten, og er ikke beregnet til bruk som lommelykt. Modusvelgerkrage (fig. 3–5) Bormaskinen er utstyrt med en separat modusvelgerkrage (f) for å veksle mellom bore-, skrutrekking- og hammerboringsmodus. BORING (FIG. 3) FORSIKTIG: Når modusvelgerkragen er i bore-/slagbormodus, vil ikke bormaskinen utløse på clutchen, uansett posisjonen til momentjusteringskragen (e).
NORSK ADVARSEL: For å redusere faren for personskade, heng IKKE verktøy fra deg i beltekroken eller heng objekter fra beltekroken. Heng KUN verktøyets beltekrok i et arbeidsbelte. ADVARSEL: For å redusere faren for alvorlig personskade, sørg for at skruen som holder beltekroken sitter godt. VIKTIG: Ved festing eller skifting av beltekroken eller bitclipset, bruk kun den medfølgende skruen (l). Påse at skruen strammes godt.
NORSK 2. Drei modusvelgerkragen (f) slik at skruesymbolet er innrettet med pilen. 3. Still så momentjusteringskragen (e) til korrekt innstilling for ønsket moment. Prøv først et par ganger på skrap eller usynlige områder for å fastslå om momentjusteringskragen har riktig posisjon. MERK: Momentjusteringskragen kan til enhver tid stilles til hvilket som helst tall. Momentjusteringskragen er bare låst når den er i skrutrekkingsmodus, og ikke i bore- eller hammerboringsmodus. Borhammerdrift (fig. 5) 1.
NORSK Hvis du en dag finner ut at DEWALT-produktet må skiftes eller du ikke lenger har bruk for det, skal du ikke kaste det sammen med det vanlige husholdningsavfallet. Sørg for at produktet innsamles separat. Separat innsamling av brukte produkter og pakkematerialer gjør det mulig å gjenvinne materialer og bruke dem på nytt. Gjenbruk av gjenvunne materialer reduserer forurensning og etterspørselen etter råvarer.
NORSK GARANTI DEWALT er overbevist om kvaliteten på produktene sine og tilbyr en enestående garanti for profesjonelle brukere av produktet. Denne garantierklæringen kommer i tillegg til, og har på ingen måte negativ innvirkning på, dine kontraktsmessige rettigheter som profesjonell bruker eller på dine lovfestede rettigheter som privat, ikke-profesjonell bruker. Garantien er gyldig innen områdene tilhørende medlemslandene i den Europeiske Union (EU) og det Europeiske Frihandelsområdet (EFTA).
PORTUGUÊS BERBEQUIM/APARAFUSADOR SEM FIOS DE 13 mm (1/2") DCD931, DCD980 MARTELO PERFURADOR/APARAFUSADOR DE 13 mm (1/2") DCD936, DCD985 Parabéns! Optou por uma ferramenta da DEWALT. Longos anos de experiência, um desenvolvimento meticuloso dos seus produtos e um grande espírito de inovação são apenas alguns dos argumentos que fazem da DEWALT um dos parceiros de maior confiança dos utilizadores de ferramentas eléctricas profissionais.
PORTUGUÊS Valor de emissão de vibrações ah Aparafusamento: ah = m/s² Instabilidade K = m/s² < 2,5 1,5 < 2,5 1,5 ATENÇÃO: o nível de emissão de vibrações declarado representa as aplicações principais para as quais a ferramenta foi concebida. Contudo, se a ferramenta for utilizada para aplicações diferentes, com acessórios diferentes ou tiver uma má manutenção, o nível de emissão de vibrações poderá diferir. Isto poderá aumentar significativamente o nível de exposição ao longo do período total de trabalho.
PORTUGUÊS Declaração de conformidade da CE b) DIRECTIVA “MÁQUINAS” DCD931, DCD936, DCD980, DCD985 A DEWALT declara que os produtos descritos em Dados técnicos se encontram em conformidade com as seguintes normas e directivas: 2006/42/CE, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Além disso, estes produtos também se encontram em conformidade com a Directiva 2004/108/CE e 2011/65/UE. Para obter mais informações, contacte a DEWALT através da morada indicada em seguida ou consulte o verso do manual.
PORTUGUÊS b) c) d) e) f) g) Use equipamento de protecção pessoal. Use sempre protecção ocular. O equipamento de protecção, como máscara anti-poeira, sapatos de segurança antiderrapantes, capacete de segurança ou protecção auricular, usado nas condições apropriadas, reduz o risco de lesões. Evite um accionamento acidental. Certifique-se de que o interruptor esteja na posição de desligado antes de ligar a fonte de alimentação eléctrica e/ ou bateria ou antes de levantar ou transportar a ferramenta.
PORTUGUÊS d) Aplicações inadequadas podem provocar fugas do líquido da bateria; evite o contacto com este líquido. No caso de um contacto acidental, lave imediatamente com água. Se o líquido entrar em contacto com os olhos, procure também auxílio médico. O líquido que escapa da bateria pode provocar irritações ou queimaduras da pele. 6) ASSISTÊNCIA a) A sua ferramenta eléctrica só deve ser reparada por pessoal qualificado e só devem ser utilizadas peças sobressalentes originais.
PORTUGUÊS ATENÇÃO: perigo de choque. Não permita a entrada de líquidos no carregador. Pode ocorrer um choque eléctrico. CUIDADO: perigo de queimadura. Para reduzir o risco de lesões, carregue apenas baterias recarregáveis DEWALT. Os outros tipos de baterias podem sobreaquecer e rebentar, resultando em lesões pessoais e danos de propriedade. Não recarregue baterias não recarregáveis. CUIDADO: As crianças devem ser vigiadas, para garantir que não brincam com o aparelho.
PORTUGUÊS muda então automaticamente para o modo de carregamento da bateria. Esta função assegura a máxima vida útil possível da bateria. Procedimento de carregamento (fig. 2) 1. Ligue o carregador numa tomada adequada de 230 V antes de inserir a bateria. 2. Insira a bateria (i) no carregador, certificando-se de que fica totalmente encaixada no carregador. O indicador luminoso vermelho (de carga) pisca continuamente, indicando que o processo de carga foi iniciado. 3.
PORTUGUÊS ATENÇÃO: nunca tente abrir a bateria, seja qual for o motivo. Se a bateria estiver rachada ou danificada, não a insira no carregador. Não esmague, deixe cair nem danifique a bateria. Não utilize uma bateria ou um carregador que tenha sofrido um golpe brusco, uma queda, atropelamento ou danificada de algum modo (por exemplo, perfurada por um prego, atingida com um martelo ou pisada). Pode ocorrer um choque eléctrico ou electrocussão.
PORTUGUÊS Não exponha o equipamento à água. Mande substituir imediatamente quaisquer cabos danificados. Carregue a bateria apenas com uma temperatura ambiente entre 4 °C e 40 °C. a. Gatilho b. Botão de controlo de avanço/recuo c. Indicador luminoso d. Mandril e. Anel de ajuste do binário f. Anel de selecção do modo g. Selector de velocidade Desfaça-se da bateria de uma forma ambientalmente responsável. h. Punho lateral Não queime a pilha. k. Gancho de correia i. Bateria j.
PORTUGUÊS Utilizar um cabo de extensão Não deverá ser utilizado um cabo de extensão, excepto em caso de absoluta necessidade. Utilize um cabo de extensão aprovado e adequado à entrada de energia do seu carregador (consulte os Dados técnicos). O tamanho mínimo do condutor é de 1 mm2; o comprimento máximo é de 30 m. No caso de se usar uma bobina, desenrole o cabo todo. MONTAGEM E AJUSTES Gatilho de velocidade variável (fig. 1) Para ligar a ferramenta, prima o gatilho (a).
PORTUGUÊS Para seleccionar a rotação para trás, liberte o gatilho e prima o botão de rotação para a frente/para trás do lado esquerdo da ferramenta. PERFURAR COM PERCUSSÃO (FIG. 5) CUIDADO: quando o anel de selecção do modo estiver configurado para o modo de perfuração normal/com percussão, o mandril do berbequim não irá desengatar-se do motor, independentemente da posição do anel de ajuste do binário (e). A posição central do botão de rotação bloqueia a ferramenta na posição de ferramenta desligada.
PORTUGUÊS Bloqueie sempre o gatilho e desligue a ferramenta da fonte de alimentação ao substituir acessórios. ATENÇÃO: certifique-se sempre de que a broca está bem apertada antes de ligar a ferramenta. Uma broca solta pode saltar da ferramenta e causar ferimentos. MANDRIL SEM CHAVE DE MANGA SIMPLES (FIG. 6–8) A sua ferramenta possui um mandril sem chave com uma manga rotativa para poder utilizar o mandril com apenas uma mão. Para inserir uma broca ou outro acessório, siga os passos indicados abaixo. 1.
PORTUGUÊS Utilização do berbequim (fig. 3) ATENÇÃO: para reduzir o risco de lesões graves, desligue a ferramenta e retire a ficha da alimentação de energia antes de proceder a quaisquer ajustes ou de remover/instalar dispositivos auxiliares ou acessórios. ATENÇÃO: para reduzir o risco de ferimentos pessoais, certifique-se SEMPRE que a peça de trabalho está firmemente ancorada ou presa por grampos. Se for perfurar material fino, utilize um bloco de “apoio” em madeira para evitar danos no material. 1.
PORTUGUÊS 5. Ao perfurar alvenaria, utilize brocas com ponta de carboneto ou brocas específicas para alvenaria. Um fluxo contínuo e uniforme de partículas indica uma velocidade de perfuração apropriada. MANUTENÇÃO Esta ferramenta eléctrica DEWALT foi concebida para o servir durante muito tempo com um mínimo de manutenção. Uma operação satisfatória e continuada depende do cuidado a ter com a ferramenta e a limpeza regular.
PORTUGUÊS Poderá verificar a localização do Centro de Assistência mais próximo contactando a delegação DEWALT na morada indicada neste manual. Em alternativa, encontrará uma lista dos Centros de Assistência Técnica DEWALT e todas as informações sobre o nosso serviço pós-venda disponíveis na Internet em: www.2helpU.com. Bateria recarregável Esta bateria de longa duração tem de ser recarregada quando deixar de produzir energia suficiente nas tarefas que anteriormente eram realizadas com facilidade.
PORTUGUÊS GARANTIA A DEWALT confia na qualidade dos seus produtos e, como tal, oferece uma garantia excepcional aos utilizadores profissionais deste equipamento. Esta declaração de garantia complementa os seus direitos contratuais enquanto utilizador profissional ou os seus direitos legais enquanto utilizador privado não profissional, não os prejudicando, seja de que forma for. A garantia é válida nos Estados-membros da União Europeia e nos países-membros da Zona Europeia de Comércio Livre.
SUOMI 13 mm (1/2") AKKUPORAKONE/RUUVINVÄÄNNIN DCD931, DCD980 13 mm (1/2") AKKUISKUPORAKONE/RUUVINVÄÄNNIN DCD936, DCD985 Onnittelut! Olet valinnut DEWALT-työkalun. Monien vuosien kokemus, huolellinen tuotekehitys ja innovaatiot tekevät DEWALT-työkaluista luotettavia kumppaneita ammattilaisille.
SUOMI Tärinän päästöarvo ah Ruuvien vääntö: ah, = Epävarmuus K = m/s² m/s² < 2,5 1,5 Tässä tiedotteessa annettu tärinäarvo on mitattu EN 60745 -määräyksen mukaisen standardoidun testin mukaan. Arvon avulla työkaluja voidaan verrata toisiinsa. Sitä voidaan käyttää altistumisen ennakkoarviointiin. VAROITUS: Ilmoitettu tärinäarvo vastaa työkalun pääasiallisia käyttösovelluksia. Jos työkalua käytetään muihin sovelluksiin, eri lisävarusteiden kanssa tai huonosti huollettuna, tärinäarvot saattavat muuttua.
SUOMI EY-vaatimustenmukaisuusvakuutus b) KONEDIREKTIIVI DCD931, DCD936, DCD980, DCD985 DEWALT vakuuttaa, että nämä tuotteet täyttävät seuraavat määräykset: 2006/42/EY, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Nämä tuotteet täyttävät myös direktiivin 2004/108/EU ja 2011/65/EU vaatimukset. Saat lisätietoja ottamalla yhteyden DEWALTiin. Osoitteet näkyvät käyttöohjeen takasivulla. Allekirjoittaja vastaa Tekniset tiedoista ja antaa tämän vakuutuksen DEWALTin puolesta.
SUOMI c) d) e) f) g) Estä tahaton käynnistäminen. Varmista, että kytkin on pois-asennossa ennen työkalun yhdistämistä virtalähteeseen ja/tai akkupakkaukseen tai ennen kuin tartut työkaluun. Työkalun kantaminen sormi kytkimellä tai pistokkeen työntäminen pistorasiaan, kun kytkin on päälle kytkettynä, voi aiheuttaa onnettomuuksia. Poista mahdolliset säätö- tai kiintoavaimet ennen työkalun käynnistämistä. Pyörivään osaan jäänyt kiinto- tai säätöavain saattaa aiheuttaa henkilövahinkoja. Älä kurottele.
SUOMI • Tartu kiinni koneen eristetyistä tartuntapinnoista, jos leikkausvälinettä käyttäessä on vaara osua piilossa oleviin johtoihin. Terän osuminen jännitteiseen johtoon tekee sen paljaista metalliosista jännitteisiä, joten käyttäjä voi saada sähköiskun. • Kiinnitä työstettävä kappale vakaaseen alustaan kiinnittimien tai muiden käytännöllisten menetelmien avulla. Työkalun pitäminen kädessä tai kehoa vasten voi aiheuttaa hallinnan menettämisen. • Käytä kuulosuojaimia pitkään jatkuvan iskuporaamisen aikana.
SUOMI • Vedä pistokkeesta äläkä johdosta, kun irrotat laturia verkkovirrasta. Tämä vähentää pistokkeen ja sähköjohdon vahingoittumisen riskiä. Lataaminen (kuva [figure] 2) 1. Yhdistä laturi sopivaa 230 V pistorasiaan ennen kuin laitat siihen akun. • Varmista, että johto sijaitsee niin, että sen päälle ei astuta, siihen ei kompastu tai että siihen ei muuten kohdistu vaurioita tai rasitusta. 2. Aseta akku (i) laturiin ja varmista, että se on hyvin paikoillaan laturissa.
SUOMI Kylmä akku latautuu puolet hitaammin lämpimään akkuun verrattuna. Akku latautuu hitaammin koko latausjakson ajan, sen latautumisnopeus ei palaudu nopeaksi, vaikka akku lämpenesi. HUOMIO: Kun työkalua ei käytetä, aseta se vakaalle alustalle kyljelleen, jotta se ei aiheuta putoamis- tai kompastumisvaaraa. Kookkaalla akulla varustetut työkalut voidaan jättää pystyasentoon, mutta ne kaatuvat helposti.
SUOMI Latauslaitteen ja akun tarrat Pakkauksen sisältö Tässä käyttöohjeessa käytettävien kuvakkeiden lisäksi latauslaitteessa ja akussa käytetään seuraavia kuvakkeita: Pakkauksen sisältö: Lue käyttöohjeet ennen käyttämistä. 1 akkukäyttöinen iskuporakone (malli DCD985, DCD936) 1 akkukäyttöinen keskikahvalla varustettu porakone (malli DCD980, DCD931) 1 Litiumioniakku (M1, L1-mallit) 2 Litiumioniakkua (M2, L2-mallit) Akkua ladataan. 3 Litiumioniakkua (M3, L3-mallit) 1 Rasia Akku on ladattu.
SUOMI ÄLÄ ANNA lasten koskea niihin. Kokemattomat henkilöt saavat käyttää tätä laitetta vain valvotusti. • Tämä tuote ei ole tarkoitettu henkilöiden (mukaan lukien lapset) käytettäväksi, joiden fyysiset, sensoriset tai henkiset kyvyt tai kokemus ja/tai tietämys tai taidot ovat rajalliset. Heidän turvallisuudestaan tulee huolehtia heistä vastuussa oleva henkilö. Lapsia ei koskaan saa jättää yksin tämän tuotteen kanssa. Sähköturvallisuus Sähkömoottori on suunniteltu vain yhdelle jännitteelle.
SUOMI Toimintasuunnan valitsin (kuva 1) Momentinvalitsin (kuvat 3–5) Voit valita toimintasuunnan ja lukita koneen valitsimen (b) avulla. Tämän työkalun vääntömomenttia voidaan säätää erilaisia ruuveja ruuvattaessa. Vääntömomentin säätimessä (e) näkyy numeroita. Vääntömomentti valitaan niiden avulla. Mitä suurempi numero, sitä suurempi vääntömomentti. Voit valita numeron kääntämällä valitsinta, kunnes numero on nuolen kohdalla.
SUOMI istukan vaippaa edelleen, kunnes kuulet useita räikän napsahduksia täydellisen kiinnityksen varmistamiseksi. Käsien oikea asento (kuva 9) Voit irrottaa varusteen toistamalla edelliset vaiheen 1 ja 2 toimet. VAROITUS: Voit vähentää vakavan henkilövahingon vaaraa pitämällä kädet AINA oikeassa asennossa kuvassa 9 näkyvällä tavalla. Kiristä istukka kääntämällä sen holkkia yhdellä kädellä ja pitämällä työkalua paikallaan toisella kädellä.
SUOMI apuvälineiden irrottamista tai asentamista. Vahingossa tapahtuva käynnistyminen voi aiheuttaa vamman. Ruuvinvääntimenä käyttäminen (kuva 4) 1. Valitse haluamasi nopeus- ja vääntömomenttialue valitsemalla jokin kolmesta vaihteesta (g). Valitse aluksi vääntömomentin säätimen (e) avulla vähäinen vääntömomentti. HUOMAA: Jos haluat ruuvata ruuvin tietylle syvyydelle, käytä alhaisinta tarvittavaa vääntömomenttia. Mitä pienempi numero, sitä vähäisempi vääntömomentti. Laturia tai akkua ei voida huoltaa.
SUOMI Ympäristön suojeleminen Lajittele osat. Tätä tuotetta ei saa hävittää normaalin kotitalousjätteen seassa. Jos huomaat DEWALT-tuotteesi vaativan vaihtoa tai jos et tarvitse sitä enää, älä hävitä sitä kotitalousjätteen mukana. Vie tuote lajiteltavaksi. Kun käytetyn tuotteen ja pakkauksen osat erotetaan toisistaan, materiaali voidaan kierrättää ja käyttää uudelleen. Kierrätetyn materiaalin uudelleen käyttö auttaa estämään ympäristön saastumista ja vähentää raaka-aineen tarvetta.
SVENSKA 1/2" (13 mm) SLADDLÖS BORR/DRIVARE DCD931, DCD980 1/2" (13 mm) SLADDLÖS SLAGBORRMASKIN/DRIVARE DCD936, DCD985 Gratulerar! Du har valt ett DEWALT-verktyg. År av erfarenhet, grundlig produktutveckling och innovation gör DEWALT till en av de pålitligaste partnerna för fackmannamässiga elverktygs-användare. Tekniska Data Spänning Type r Batterityp Strömmatning Frigångshastighet 1:a växel 2:a växel 3:e växel Slaghastighet 1:a växel 2:a växel 3:e växel Max.
SVENSKA Vibration, emissionsvärde ah Inskruvning: ah = Osäkerhet K = m/s² m/s² < 2,5 1,5 < 2,5 1,5 Vibrationsemissionsnivån som anges i det här informationsbladet har mätts i enlighet med ett standardprov i EN 60745 och kan användas för att jämföra ett verktyg med ett annat. Det kan användas för en preliminär uppskattning av exponering. VARNING: De deklarerade vibrationsemissionsnivåerna representerar verktygets huvudtillämpningar.
SVENSKA EG-deklaration om överensstämmelse b) MASKINDIREKTIV c) DCD931, DCD936, DCD980, DCD985 DEWALT deklarerar att dessa produkter, beskrivna under Tekniska data uppfyller: 2006/42/EY, EN 60745-1, EN 60745-2-1, EN 60745-2-2. Dessa produkter uppfyller dessutom direktiv 2004/108/EC och 2011/65/EU. För mer information, var god kontakta DEWALT på följande adress, eller se handbokens baksida. Undertecknad är ansvarig för sammanställning av den tekniska filen och gör denna förklaring å DEWALTs vägnar.
SVENSKA d) e) f) g) och/eller batteripaket, eller då du lyfter eller bär det. Att bära elverktyg med fingret på strömbrytaren eller att koppla på strömmen då strömbrytaren är påslagen inbjuder till olyckor. Avlägsna alla justeringsnycklar och skiftnycklar innan elverktyget slås på. En skiftnyckel eller skruvnyckel som sitter kvar i en roterande del av ett elverktyg kan orsaka personskada. Sträck dig inte för långt. Ha alltid säkert fotfäste och balans.
SVENSKA • Använd klämmor eller annan praktisk metod för att förankra och stödja arbetsstycket på en stabil plattform. Att hålla arbetet med handen eller mot din kropp är instabilt, och kan leda till förlust av kontroll. • Bär öronskydd vid slagborrning under utdragna tidsperioder. Att utsättas för högt buller under lång tid kan orsaka hörselförlust. Temporär förlust av hörseln eller allvarlig skada på trumhinnan kan orsakas av de höga ljudnivåer som uppstår genom slagborrning.
SVENSKA • Använd inte förlängningssladd såvida inte det är absolut nödvändigt. Användning av en olämplig förlängningssladd kan resultera i risk för brand. elektriska stötar eller död av elektrisk ström. • När en laddare hanteras utomhus, gör detta alltid på en torr plats och använd en förlängningssladd som är avsedd för utomhusbruk. Användning av en sladd som passar för utomhusanvändning minskar risken för elektrisk stöt. Laddningsprocedur (bild [fig.] 2) 1.
SVENSKA Verktyget kommer automatiskt att koppla från det om det elektroniska skyddssystemet aktiveras. Om detta inträffar, låt Li-jon-batteriet sitta i laddaren till dess det är full-laddat. elektisk ström. Skadade batteripaket skall returneras till servicecenter för återvinning. SE UPP! När det inte används, placera verktyget på sin sida, på en stadig yta, där det inte kommer att orsaka fara för snavande eller fallande.
SVENSKA OBSERVERA: Batteripaket bör inte förvaras helt urladdade. Batteripaketet behöver laddas innan det används igen. Etiketter på laddare och batteripaket Som tillägg till de piktografier som används i denna handbok visar etiketterna på laddaren och batteripaketet följande piktografier: Läs instruktionshandbok före användning. Endast för användning inomhus.
SVENSKA Använd INTE under våta förhållanden eller i närheten av lättantändliga vätskor eller gaser. Dessa borrmaskiner/drivare/slagborrmaskiner är yrkesmässiga elverktyg. LÅT INTE barn komma i kontakt med verktyget. Överinseende erfordras när oerfarna användare använder detta verktyg.
SVENSKA Sidohandtaget (h) hålls fast på växellådans framdel, och kan vridas 360˚ för att tillåta högerhänt eller vänsterhänt användning. Sidohandtaget måste vara tillräckligt hårt åtdraget för att motstå verktygets vridande kraft om tillbehöret fastnar eller överstegrar. Se till att greppa sidohandtaget vid den bortre änden för att kunna kontrollera verktyget under en överstegring. Vrid reglaget för lägeskontroll (f) så att borr-symbolen står mittför pilen.
SVENSKA Chuckar VARNING: Försök inte att dra åt borrspetsar (eller något annat tillbehör) genom att greppa chuckens framdel och sätta igång verktyget. Skada på chucken och personskada kan uppstå. Släpp alltid avtryckaren från sitt låsta läge och koppla bort verktyget från strömkällan när du byter tillbehör. VARNING: Se alltid till att borrspetsen sitter fast innan du startar verktyget. En lös borrspets kan skjutas iväg från verktyget och möjligen orsaka personskada.
SVENSKA VARNING: För att minska risken för personskada, skall du ALLTID se till att arbetsstycket sitter väl förankrat eller fastklämt. Om du borrar i tunt material, skall du använda ett ”bakstycke” av trä, för att hindra att materialet skadas. 1. Välj det önskade intervallet för hastighet/ vridmoment genom att använda växelbytaren, så att det matchar hastigheten och vridmomentet för det planerade arbetsmomentet. Sätt reglaget för lägeskontroll mittför borrspets-symbolen. 2.
SVENSKA Smörjning Ditt elverktyg behöver ingen extra smörjning. Rengöring VARNING! Blås ut smuts och damm ur verktygshuset med torr luft när man kan se smuts samlas i och runt luftventilerna. Bär godkända skyddsglasögon och godkänd andningsmask när du utför denna procedur. VARNING! Använd aldrig lösningsmedel eller andra starka kemikalier för rengöring av de delar som inte är av metall. Kemikalierna kan försvaga materialet i de här delarna. Använd en trasa enbart fuktad med vatten och mild tvållösning.
SVENSKA GARANTI DEWALT har förtroende för kvaliteten på sina produkter, och erbjuder en enastående garanti för professionella användare av produkten. Denna garanti-deklaration kommer som tillägg till och inskränker inte dina kontraktsmässiga rättigheter i egenskap av professionell användare, eller dina lagstadgade rättigheter i egenskap av enskild icke-professionell användare. Garantin är giltig i de territorier som tillhör medlemsstaterna i Europeiska unionen och det europeiska frihandelsområdet.
TÜRKÇE 13 mm (1/2") ŞARJLI MATKAP/TORNAVİDA DCD931, DCD980 13 mm (1/2") ŞARJLI DARBELİ MATKAP/TORNAVİDA DCD936, DCD985 Tebrikler! Bir DEWALT aleti seçtiniz. Uzun süreli deneyim, sürekli ürün geliştirme ve yenilik DEWALT markasının profesyonel elektrikli alet kullanıcıları için en güvenilir ortaklardan birisi haline gelmesini sağlamaktadır. Teknik veriler Voltaj Tipler Akü tipi Çıkış gücü Yüksüz hız 1. vites 2. vites 3. vites Darbe oranı 1. vites 2. vites 3. vites Maks.
TÜRKÇE Titreşim emisyon değeri ah Vidalama: ah = Belirsizlik K = m/s² m/s² < 2,5 1,5 < 2,5 1,5 VDC Ah kg Şarj Cihazı Ana şebeke voltajı Akü tipi Yaklaşık şarj süresi dak Ağırlık kg DCB140 DCB141 Li-İyon Li-İyon 14,4 14,4 3,0 1,5 0,53 0,30 VAC 30 (1,5 Ah akü) 230 V aletler DCB412 Li-İyon 14,4 4,0 0,54 DCB105 230 Li-İyon 55 (3,0 Ah akü) DCB180 Li-İyon 18 3,0 0,64 DCB181 Li-İyon 18 1,5 0,35 DCB182 Li-İyon 18 4,0 0,61 70 (4,0 Ah akü) 0,49 Sigortalar: Avrupa < 2,5 1,5 Tahmini titreşim maruziy
TÜRKÇE AT uygunluk beyanatı MAKİNE DİREKTİFİ DCD931, DCD936, DCD980, DCD985 DEWALT, Teknik veriler bölümünde açıklanan bu ürünlerin 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2 normlarına uygun olarak tasarlandığını beyan eder. Bu ürünler ayrıca 2004/108/EC ve 2011/65/EU Direktifi ile uyumludur. Daha fazla bilgi için, lütfen aşağıdaki adresten DEWALT ile irtibata geçin veya kılavuzun arkasına bakın.
TÜRKÇE b) Kişisel koruyucu ekipmanları mutlaka kullanın. Daima koruyucu gözlük takın. Koşullara uygun toz maskesi, kaymayan güvenlik ayakkabıları, baret veya kulaklık gibi koruyucu donanımların kullanılması kişisel yaralanmaları azaltacaktır. c) İstem dışı çalıştırılmasını önleyin. Cihazı güç kaynağına ve/veya aküye bağlamadan, yerden kaldırmadan veya taşımadan önce düğmenin kapalı konumda olduğundan emin olun.
TÜRKÇE 6) SERVIS a) Elektrikli aletinizi, sadece orijinal yedek parçaların kullanıldığı yetkili DEWALT servisine tamir ettirin. Bu, elektrikli aletin güvenliğinin muhafaza edilmesini sağlayacaktır. – İşitme bozukluğu. Matkap/Tornavida/Darbeli Matkaplar için İlave Özel Güvenlik Kuralları – Sıçrayan parçacıklardan kaynaklanan yaralanma riski. • Darbeli matkapla çalışırken koruyucu kulaklık kullanın. Gürültüye maruz kalınması, işitme kaybına yol açabilir.
TÜRKÇE • • • • • • • • • • İKAZ: Belirli koşullar altında, şarj cihazı güç kaynağına takılıyken, yabancı maddeler tarafından kısa devre yapılabilir. Bunlarla sınırlı olmamak kaydıyla iletken nitelikteki taşlama tozu, metal yongalar, çelik yünü, alüminyum folyo veya metal parçacık birikimi gibi yabancı maddeler şarj cihazının yuvalarından uzak tutulmalıdır. Yuvada akü yokken şarj cihazını daima güç kaynağından çıkarın. Şarj cihazının fişini temizlemeden önce çıkarın.
TÜRKÇE Şarj İşlemi A künün şarj durumu için aşağıdaki tabloya bakın. Şarj durumu x şarj oluyor –– tamamen şarj oldu ––––––––––––––––– sıcak/soğuk akü gecikmesi paket veya şarj cihazında sorun güç hattında sorun –– –– –– –– • –– • –– • –– • •••••••••••••• •• •• •• •• •• •• •• Bu şarj cihazı arızalı bir akü takımını şarj etmeyecektir. Şarj cihazı, ışığı geri çevirerek veya paket ya da şarj sorunu yanıp sönme şablonunu görüntüleyerek akünün arızalı olduğunu gösterecektir.
TÜRKÇE LİTYUM İYON İÇİN ÖZEL GÜVENLİK TALİMATLARI (Li-Ion) • Önemli ölçüde hasarlı veya tamamen eskimiş olsa bile aküyü ateşe atmayın. Akü ateşe atılırsa patlayabilir. Lityum iyon aküler yanınca zehirli buharlar ve materyaller açığa çıkar. • Akü içeriği cildinizle temas ederse, etkilenen alanı derhal yumuşak bir sabun ve suyla yıkayın. Akü sıvısı gözlerinize bulaşırsa, gözünüzü açık tutarak 15 dakika boyunca veya tahriş hissi geçene kadar suyla yıkayın.
TÜRKÇE Şarj süresi için Teknik veriler bölümüne bakın. l. Montaj vidası m. Uç klipsi KULLANIM ALANI Yalnızca iç mekanda kullanım içindir.
TÜRKÇE UYARI: Sadece DEWALT aküleri ve şarj aletleri kullanın. Aküyü Alete Takıp Çıkarma (şekil 2) NOT: En iyi sonucu almak için, kullanmadan önce akü takımının tamamen şarj edildiğinden emin olun. AKÜ PAKETINI ALETIN KOLUNA TAKMA 1. Batarya paketini (j) tutamağın içindeki raylarla hizalayın (şek. 2). 2. Batarya paketini, alete tamamen oturana kadar tutamağa doğru kaydırın ve raydan çıkmadığından emin olun. AKÜ PAKETINI ALETTEN ÇIKARMA 1.
TÜRKÇE NOT: Çalışma ışığı, çalışılan yakın yüzeyi aydınlatmak içindir ve lamba olarak kullanılması amaçlanmamıştır. Mod Kontrol Bileziği (şekil 3–5) Delme, vidalama ve darbeli delme konumları arasında geçiş yapmak için matkabınızda ayrı bir mod kontrol bileziği (f) bulunmaktadır. DELME (ŞEKİL 3) DİKKAT: Mod bileziği delme/darbeli delme konumundayken tork ayarlama bileziğinin (e) pozisyonu ne olursa olsun matkap vites değiştirmeyecektir.
TÜRKÇE Aksesuarı çıkarmak için yukarıda anlatılan 1. ve 2 adımı tekrarlayın. Uygun El Pozisyonu (şekil 9) Azami sıkılık için mandreni, mutlaka bir elinizle mandren kovanını diğer elinizle aleti tutarak sıkın. UYARI: Ciddi yaralanma riskini azaltmak için, DAİMA şekil 9’da gösterilen uygun el pozisyonunu kullanın. Kemer Kancası ve Uç Klipsi (şekil 1) UYARI: Ciddi yaralanma riskini azaltmak için, ani tepki ihtimaline karşı aleti DAİMA sıkıca tutun.
TÜRKÇE 6. Delinen delikten ucu geri çekerken motoru çalışır durumda muhafaza edin. Bu işlem sıkışmayı önlemeye yardımcı olur. Vidalama İşlemi (şekil 4) 1. Planlanan işleme uygun hız ve tork seçmek için aletin üst kısmındaki üç hızlı vites mandalını (g) kullanarak istenilen hız/ tork aralığını seçin. Vidanın gerekli şekilde sıkılmasını sağlamak için tork ayarlama bileziğini (e) ilk başta düşük bir ayara ayarlayın. NOT: Vidayı istenilen derinliğe oturtmak için gereken en düşük tork ayarını kullanın.
TÜRKÇE ŞARJ CİHAZI TEMİZLEME TALİMATLARI UYARI: Şok tehlikesi. Temizlemeden önce şarj cihazının fişini AC prizinden çekin. Bir bez veya metalik olmayan yumuşak bir fırça kullanılarak, şarj cihazının dışındaki kir ve yağ çıkartılabilir. Su veya başka bir temizleme solüsyonu kullanmayın. İlave aksesuarlar UYARI: DEWALT tarafından tedarik veya tavsiye edilenlerin dışındaki aksesuarlar bu ürün üzerinde test edilmediğinden, söz konusu aksesuarların bu aletle birlikte kullanılması tehlikeli olabilir.
TÜRKÇE GARANTİ DEWALT ürünlerinin kalitesinden emindir ve bu yüzden profesyonel kullanıcılar için kanunlarda belirtilen taleplerin üstünde bir garanti sunmaktadır. Bu garanti metni bir ilave niteliğinde olup profesyonel bir kullanıcı olarak sahip olduğunuz sözleşmeden doğan haklara veya profesyonel olmayan, özel bir kullanıcı olarak sahip olduğunuz yasal haklara hiçbir şekilde zarar vermez. İşbu garanti Avrupa Birliği’ne üye ülkeler ile Avrupa Serbest Ticaret Bölgesi sınırları dahilinde geçerlidir.
ΕΛΛΗΝΙΚΑ 13 mm (1/2") ΑΣΥΡΜΑΤΟ ΔΡΑΠΑΝΟ/ΟΔΗΓΟΣ DCD931, DCD980 13 mm (1/2") ΑΣΥΡΜΑΤΟ ΣΦΥΡΟΤΡΥΠΑΝΟ/ DCD936, DCD985 Συγχαρητήρια! Επιλέξατε ένα εργαλείο DEWALT. Τα έτη εμπειρίας, η προσεκτική ανάπτυξη των προϊόντων και η καινοτομία έχουν καταστήσει την DEWALT έναν από τους πιο αξιόπιστους συνεργάτες για τους χρήστες των επαγγελματικών εργαλείων.
ΕΛΛΗΝΙΚΑ Τιμή εκπομπής κραδασμών ah Διάτρηση με κρούση ah,ID = m/s2 Αβεβαιότητα K = m/s2 – – 11,0 1,5 – – 11,0 1,5 Τιμή εκπομπής κραδασμών ah Βίδωμα: m/s² ah = Αβεβαιότητα K = m/s² < 2,5 1,5 < 2,5 1,5 < 2,5 1,5 < 2,5 1,5 Το επίπεδο εκπομπής κραδασμών που παρέχεται στο παρόν φυλλάδιο πληροφοριών έχει μετρηθεί σύμφωνα με τυποποιημένο τεστ του προτύπου ΕΝ 60745 και μπορεί να χρησιμοποιηθεί για τη σύγκριση ενός εργαλείου με ένα άλλο. Μπορεί να χρησιμοποιηθεί για προκαταρκτική αξιολόγηση έκθεσης.
ΕΛΛΗΝΙΚΑ ΠΡΟΣΟΧΗ: Καθορίζει μια ενδεχομένως επικίνδυνη κατάσταση η οποία, εάν δεν αποφευχθεί, ενδέχεται να προκαλέσει ελαφρό ή μέσης σοβαρότητας τραυματισμό. ΣΗΜΕΙΩΣΗ: Υποδεικνύει μια πρακτική που δεν έχει σχέση με προσωπικό τραυματισμό και η οποία, εάν δεν αποφευχθεί, ενδέχεται να προκαλέσει υλική ζημιά. Υποδηλώνει κίνδυνο ηλεκτροπληξίας. Υποδηλώνει κίνδυνο φωτιάς. Δήλωση συμμόρφωσης με τις οδηγίες της Ε.Ε.
ΕΛΛΗΝΙΚΑ β) Αποφύγετε την επαφή του σώματώς σας με γειωμένες επιφάνειες όπως σωλήνες, καλοριφέρ, εστίες κουζινών και ψυγεία. Ο κίνδυνος ηλεκτροπληξίας αυξάνεται όταν το σώμα σας είναι γειωμένο. γ) Μην εκθέτετε τα ηλεκτρικά εργαλεία στη βροχή ή σε συνθήκες υγρής ατμόσφαιρας. Η είσοδος νερού σε ηλεκτρικό εργαλείο αυξάνει τον κίνδυνο ηλεκτροπληξίας. δ) Μην κακομεταχειρίζεστε το καλώδιο. Μη χρησιμοποιείτε ποτέ το καλώδιο για τη μεταφορά, τράβηγμα, ή αποσύνδεση του ηλεκτρικού εργαλείου.
ΕΛΛΗΝΙΚΑ γ) Αποσυνδέστε το βύσμα από την πρίζα ή και το πακέτο μπαταρίας από το ηλεκτρικό εργαλείο πριν κάνετε οποιεσδήποτε ρυθμίσεις, αλλαγές παρελκομένων, ή πριν αποθηκεύσετε οποιοδήποτε ηλεκτρικό εργαλείο. Αυτού του είδους τα μέτρα ασφαλείας μειώνουν τον κίνδυνο απροσδόκητης λειτουργίας του ηλεκτρικού εργαλείου.
ΕΛΛΗΝΙΚΑ εκτελείτε μια εργασία όπου το αξεσουάρ κοπής μπορεί να έρθει σε επαφή με αθέατα καλώδια. Αν αξεσουάρ κοπής έρθει σε επαφή με καλώδιο υπό τάση μπορεί να τεθούν υπό ηλεκτρική τάση και τα εκτεθειμένα μεταλλικά μέρη του ηλεκτρικού εργαλείου και να προκληθεί ηλεκτροπληξία στο χειριστή. • Χρησιμοποιήστε σφιγκτήρες ή άλλο πρακτικό τρόπο για τη στερέωση με ασφάλεια και την υποστήριξη του υπό κατεργασία αντικειμένου σε μια σταθερή πλατφόρμα.
ΕΛΛΗΝΙΚΑ • • • • • • • ΠΡΟΣΟΧΗ: Τα παιδιά θα πρέπει να βρίσκονται υπό επίβλεψη ώστε να διασφαλίζεται ότι δεν παίζουν με τη συσκευή. ΣΗΜΕΙΩΣΗ: Υπό ορισμένες συνθήκες, με το φορτιστή συνδεδεμένο στην παροχή ρεύματος, ο φορτιστής μπορεί να βραχυκυκλωθεί από ξένο υλικό.
ΕΛΛΗΝΙΚΑ Αυτός ο φορτιστής δεν απαιτεί καμία ρύθμιση και έχει σχεδιαστεί να λειτουργεί όσο το δυνατόν πιο απλά. Διαδικασία φόρτισης (εικ. [fig.] 2) 1. Συνδέστε το φορτιστή σε κατάλληλη πρίζα 230 V πριν τοποθετήσετε το πακέτο μπαταριών. 2. Εισάγετε το πακέτο μπαταριών (i) μέσα στο φορτιστή και βεβαιωθείτε ότι το πακέτο έχει τερματίσει πλήρως στην κανονική του θέση μέσα στο φορτιστή. Η κόκκινη λυχνία (φόρτισης) θα αναβοσβήνει συνεχώς υποδηλώνοντας ότι έχει αρχίσει η διαδικασία φόρτισης. 3.
ΕΛΛΗΝΙΚΑ • • • • με μη συμβατό φορτιστή, γιατί το πακέτο μπαταριών μπορεί να σπάσει προκαλώντας σοβαρό τραυματισμό. Φορτίζετε τα πακέτα μπαταριών μόνο σε προβλεπόμενους φορτιστές DEWALT. ΜΗΝ πιτσιλίζετε ή βυθίζετε σε νερό ή άλλα υγρά. Μην αποθηκεύετε ή χρησιμοποιείτε το εργαλείο και το πακέτο μπαταριών σε θέσεις όπου η θερμοκρασία μπορεί να φθάσει ή να υπερβεί τους 40 ˚C (105 °F) (όπως έξω από καλυμμένα μέρη ή σε μεταλλικά κτίρια το καλοκαίρι).
ΕΛΛΗΝΙΚΑ Ετικέτες στο φορτιστή και την μπαταρία Φορτίζει μπαταρίες Li-Ion. Ανατρέξτε στα Τεχνικά δεδομένα για το χρόνο φόρτισης. Εκτός από τα εικονογράμματα που χρησιμοποιούνται στο παρόν εγχειρίδιο, στις ετικέτες του φορτιστή και της μπαταρίας εμφανίζονται τα ακόλουθα εικονογράμματα: Διαβάστε το εγχειρίδιο οδηγιών πριν από τη χρήση. Μόνο για χρήση σε εσωτερικό χώρο. Περιεχόμενα συσκευασίας Στη συσκευασία περιέχεται: 1 ασύρματο κρουστικό δράπανο (μοντέλα DCD985, DCD936) Φόρτιση μπαταρίας.
ΕΛΛΗΝΙΚΑ i. Μπαταρία j. Κουμπιά απελευθέρωσης μπαταρίας k. Άγκιστρο ζώνης l. Βίδα στερέωσης m. Κλιπ αξεσουάρ ΠΡΟΟΡΙΖΟΜΕΝΗ ΧΡΗΣΗ Αυτά τα δραπανοκατσάβιδα/κρουστικά δράπανα έχουν σχεδιαστεί για επαγγελματικές εφαρμογές διάτρησης, κρουστικής διάτρησης και βιδώματος/ ξεβιδώματος. ΜΗΝ τα χρησιμοποιείτε σε συνθήκες υγρασίας ή όταν υπάρχουν εύφλεκτα υγρά ή αέρια. Τα δράπανα/οδηγοί/σφυροτρύπανα είναι επαγγελματικά ηλεκτρικά εργαλεία. ΜΗΝ αφήνετε τα παιδιά να έρχονται σε επαφή με το εργαλείο.
ΕΛΛΗΝΙΚΑ Εάν το μοντέλο δεν είναι εξοπλισμένο με πλευρική λαβή, κρατήστε το δράπανο με το ένα χέρι στη λαβή και το άλλο χέρι στην μπαταρία. Για να ενεργοποιήσετε το δείκτη φορτίου, πατήστε και κρατήστε πατημένο το κουμπί (o) του δείκτη φορτίου. Θα ανάψει ένας συνδυασμός των τριών πράσινων λυχνιών LED που είναι ενδεικτικός του επιπέδου του φορτίου που απομένει.
ΕΛΛΗΝΙΚΑ για εναλλαγή μεταξύ των τρόπων λειτουργίας διάτρησης, βιδώματος και σφυρηλάτησης. ΔΙΑΤΡΗΣΗ (ΕΙΚ. 3) ΠΡΟΣΟΧΗ: Όταν το κολάρο τρόπου λειτουργίας είναι σε λειτουργία διάτρησης/σφυρηλάτησης, δεν θα είναι δυνατή η αλλαγή θέσης του συμπλέκτη του δράπανου ανεξάρτητα από τη θέση του κολάρου ρύθμισης ροπής (e). Περιστρέψτε το κολάρο ελέγχου τρόπου λειτουργίας (f) έτσι ώστε το σύμβολο διάτρησης να είναι ευθυγραμμισμένο με το βέλος.
ΕΛΛΗΝΙΚΑ ΣΦΙΓΚΤΗΡΑΣ ΔΡΑΠΑΝΟΥ ΧΩΡΙΣ ΚΛΕΙΔΙ ΜΕ ΕΝΑ ΠΕΡΙΒΛΗΜΑ (ΕΙΚ. 6–8) Το εργαλείο διαθέτει έναν σφιγκτήρα δράπανου χωρίς κλειδί με ένα περιστρεφόμενο περίβλημα για λειτουργία του σφιγκτήρα με το ένα χέρι. Για να εισαγάγετε ένα τρυπάνι δράπανου ή κάποιο άλλο εξάρτημα, ακολουθήστε τα παρακάτω βήματα. 1. Ασφαλίστε τον διακόπτη ενεργοποίησης στη θέση OFF (Απενεργοποίηση). Θέστε το εργαλείο εκτός λειτουργίας και αποσυνδέστε το από την τροφοδοσία. 2.
ΕΛΛΗΝΙΚΑ Κατάλληλη θέση των χεριών σημαίνει το ένα χέρι στην κύρια λαβή (n) και το άλλο χέρι στην πλευρική λαβή (h). Λειτουργία δράπανου (εικ. 3) ΠΡΟΕΙΔΟΠΟΙΗΣΗ: Για τη μείωση κινδύνου σοβαρού προσωπικού τραυματισμού, απενεργοποιήστε το εργαλείο και αποσυνδέστε το από την παροχή ρεύματος πριν κάνετε οποιεσδήποτε ρυθμίσεις ή αφαιρέσετε/ εγκαταστήσετε εξαρτήματα ή παρελκόμενα.
ΕΛΛΗΝΙΚΑ Λειτουργία σφυρηλάτησης (εικ. 5) 1. Επιλέξτε την επιθυμητή ταχύτητα/ περιοχή ροπής στρέψης χρησιμοποιώντας τον μεταβολέα ταχύτητας έτσι ώστε να ταιριάζει στην ταχύτητα και τη ροπή στρέψης της προγραμματισμένης εργασίας. Ρυθμίστε το κολάρο επιλογής τρόπου λειτουργίας (f) στο σύμβολο σφυρηλάτησης. 2. Κατά τη διάτρηση, χρησιμοποιείτε επαρκή δύναμη στη σφύρα για να αποτρέπεται η υπερβολική αναπήδηση.
ΕΛΛΗΝΙΚΑ Προαιρετικά παρελκόμενα ΠΡΟΕΙΔΟΠΟΙΗΣΗ: Ορισμένα εξαρτήματα εκτός απ’ αυτά που διατίθενται από την DEWALT, δεν έχουν δοκιμαστεί μ’ αυτό το προϊόν. Η χρήση αυτών των εξαρτημάτων με το παρόν εργαλείο μπορεί να αποβεί επικίνδυνη. Για τη μείωση του κινδύνου τραυματισμού, πρέπει να χρησιμοποιείτε μ’ αυτό το προϊόν μόνο τα εξαρτήματα που συνιστώνται από τη DEWALT. Συμβουλευτείτε τον αντιπρόσωπό σας για περισσότερες λεπτομέρειες όσον αφορά τα κατάλληλα παρελκόμενα.
ΕΛΛΗΝΙΚΑ ΕΓΓΥΗΣΗ DEWALT έχει εμπιστοσύνη στην ποιότητα των προϊόντων της και προσφέρει μια εξαιρετική εγγύηση για επαγγελματίες χρήστες του προϊόντος. Η παρούσα δήλωση εγγύησης είναι επιπλέον των συμβατικών δικαιωμάτων σας ως επαγγελματία χρήστη ή των απορρεόντων από τη νομοθεσία δικαιωμάτων σας ως ιδιώτη, μη επαγγελματία χρήστη και δεν τα παραβλάπτει με κανέναν τρόπο. Η εγγύηση ισχύει εντός της επικράτειας των χωρών μελών της Ευρωπαϊκής Ένωσης και της Ευρωπαϊκής Ζώνης Ελεύθερων Συναλλαγών.
197
Belgique et Luxembourg België en Luxemburg Black & Decker - DEWALT Nieuwlandlaan 7, IZ Aarschot B156 B-3200 Aarschot Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70201511 Fax: 70224910 www.dewalt.dk Deutschland DEWALT Richard Klinger Str. 11 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Ελλάς) Α.Ε. Στράβωνος 7 & Βουλιαγμένης 159 Γλυφάδα 16674, Αθήνα España DEWALT Parque de Negocios “Mas Blau” Edificio Muntadas, c/Bergadá, 1, Of.