DCD932 DCD937 DCD990 DCD995
Dansk (oversat fra original brugsvejledning) 3 Deutsch (übersetzt von den Originalanweisungen) 17 English (original instructions) 33 Español (traducido de las instrucciones originales) 46 Français (traduction de la notice d’instructions originale) 61 Italiano (tradotto dalle istruzioni originali) 76 Nederlands (vertaald vanuit de originele instructies) 91 Norsk (oversatt fra de originale instruksjonene) 106 Português (traduzido das instruções originais) 120 Suomi (käännetty alkuperäisestä
Figure 1 e d f g b a DCD990 i c l k i j h h Figure 2 h i m 1
Figure 3 Figure 4 Figure 5 e e f f Figure 7 Figure 6 Figure 8 d Figure 9 g n 2
ENGLISH BRUSHLESS CORDLESS 13 mm (12") DRILL/DRIVER, DCD932, DCD990 BRUSHLESS CORDLESS 13 mm (12") DRILL/DRIVER/HAMMERDRILL, DCD937, DCD995 Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical Data Voltage Type Battery Type Power output No-load speed 1st gear 2nd gear 3rd gear Impact rate 1st gear 2nd gear 3rd gear Max.
EN GLI S H Vibration emission value ah Screwdriving ah = Uncertainty K = m/s² m/s² < 2.5 1.5 < 2.5 1.5 WARNING: The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. Battery pack Battery type Voltage Capacity Weight VDC Ah kg DCB141 Li-Ion 14.4 1.5 0.
ENGLISH NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage. Denotes risk of electric shock. Denotes risk of fire. EC-Declaration of Conformity MACHINERY DIRECTIVE DCD932, DCD937, DCD990, DCD995 DEWALT declares that these products described under Technical Data are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. These products also comply with Directive 2004/108/EC and 2011/65/EU.
EN GLI S H c) d) e) f) g) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach.
ENGLISH • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Wear ear protectors when hammering for extended periods of time. Prolonged exposure to high intensity noise can cause hearing loss. Temporary hearing loss or serious ear drum damage may result from high sound levels generated by hammerdrilling. • Wear safety goggles or other eye protection.
EN GLI S H • When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. charger. The red (charging) light will blink continuously indicating that the charging process has started. 3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger.
ENGLISH Important Safety Instructions for All Battery Packs When ordering replacement battery packs, be sure to include the catalog number and voltage. The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow the charging procedures outlined. READ ALL INSTRUCTIONS • Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
EN GLI S H 2 14.4 V Li-Ion battery packs (DCD932, DCD937) Read instruction manual before use. 2 18 V Li-Ion battery packs (DCD990, DCD995) 1 Kitbox 1 Charger Charging. 1 Side handle 1 Instruction manual x Fully charged. 1 Exploded drawing Hot/cold pack delay. NOTE: Battery packs, chargers and kitboxes are not included with N-models. Problem pack or charger. Problem powerline. Do not probe with conductive objects.
ENGLISH supervised by a person responsible for their safety. Children should never be left alone with this product. Electrical Safety The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains. Your DEWALT charger is double insulated in accordance with EN 60335; therefore no earth wire is required.
EN GLI S H If model is not equipped with side handle, grip drill with one hand on the handle and one hand on the battery pack. Speed 2 (middle torque and speed setting) is in the middle position. Speed 3 (highest speed setting) is to the rear. NOTE: Side handle comes equipped on all models. Forward/Reverse Control Button (fig. 1) NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete stop before changing gears.
ENGLISH Belt Hook and Magnetic Bit Holder (fig. 1) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook. ONLY hang tool’s belt hook from a work belt. WARNING: To reduce the risk of serious personal injury, ensure the screw holding the belt hook is secure.
EN GLI S H depth. The lower the number, the lower the torque output. 2. Reset the torque adjustment collar (e) to the appropriate number setting for the torque desired. Make a few practice runs in scrap or unseen areas to determine the proper position of the torque adjustment collar. NOTE: The torque adjustment collar may be set to any number at any time. Hammerdrill Operation (fig. 5) 1. Select the desired speed/torque range using the gear shifter to match the speed and torque to the planned operation.
ENGLISH Should you find one day that your DEWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
Belgique et Luxembourg België en Luxemburg Black & Decker - DEWALT Nieuwlandlaan 7, IZ Aarschot B156 B-3200 Aarschot Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70201511 Fax: 70224910 www.dewalt.dk Deutschland DEWALT Richard Klinger Str. 11 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Ελλάς) Α.Ε. Στράβωνος 7 & Βουλιαγμένης 159 Γλυφάδα 16674, Αθήνα España DEWALT Parque de Negocios “Mas Blau” Edificio Muntadas, c/Bergadá, 1, Of.
