INSTRUCTION MANUAL DCF680, DCF682 8V Max* Cordless Gyroscopic Screwdriver DCF681 8V Max* Cordless Gyroscopic Electrician's Screwdriver
Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.
5) BATTERY TOOL USE AND CARE a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. WARNING: To reduce the risk of injury do not carry this tool in your pocket.
not insert into the charger. Do not crush, drop or damage the battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to the service center for recycling. NOTE: Battery storage and carrying caps are provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool.
Important Safety Instructions for All Battery Chargers SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for battery chargers. • Before using the charger, read all instructions and cautionary markings on the charger, battery pack and product using the battery pack. WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock may result. CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable battery packs.
Chargers Your tool uses a DEWALT charger. Be sure to read all safety instructions before using your charger. Consult the chart at the end of this manual for compatibility of chargers and battery packs. Charging Procedure (Fig. 1) 1. Plug the charger into an appropriate outlet before inserting the battery pack. 2. Insert the battery pack (G) into the charger, as shown in Figure 1, making sure the pack is fully seated in charger.
automatically switches to the pack charging mode. This feature ensures maximum battery life. The red light flashes long, then short while in the hot/cold delay mode. LEAVING THE BATTERY PACK IN THE CHARGER The charger and battery pack can be left connected with the charge indicator showing Pack Charged. WEAK BATTERY PACKS: Weak batteries will continue to function but should not be expected to perform as much work. FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack.
FIG. 2 Components (Fig. 2) DCF680 H J C A D I B E F DCF681 C D L E G K C M D A B F DCF682 E H A B F WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. H. Quick release Chuck A. Motion control activation (DCF680, DCF682) trigger I. Torque adjustment collar B. Lock-off switch (DCF680 Only) C. LED worklight J. Release button D. Battery fuel gauge (DCF680 Only) E. Battery release button K. Cone (DCF681 Only) F. Battery pack L.
Two-Position Screwdriver (Fig. 3) OPERATION DCF680 To convert the tool to an angled screwdriver push on the release button (D) and rotate the top portion of the tool as shown. WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. CAUTION: To avoid accidental activation during transport or storage, put the lock-off switch (Fig.
When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged. NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application. To Operate Your screwdriver uses gyroscopic technology to sense your hand motion.
DCF681 Insert the appropriate hex shank bit into the magnetic bit holder (G). Refer to To Operate for instructions. FIG. 7 Operation as a Deburring Tool (Fig. 2, 7) DCF681 WARNING: Always keep hands and clothing away from the cutting area of the tool. WARNING: Only retract the cone by pressing against a pipe end. Do not lock the cone in the retracted position. NOTICE: When deburring it is recommended to leave a hex bit in the magnetic holder.
Repairs The charger and battery pack are not serviceable. To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. Always use identical replacement parts. When deburring becomes difficult a new cutter may be required. INSTALLING REPLACEMENT CUTTER ACCESSORY DWA2601IR (FIG.
DEWALT Battery and Charger Systems Chargers/Charge Time (Minutes) – Chargeurs/Durée de charge (Minutes) – Cargadores de baterías/Tiempo de carga (Minutos) 120 Volts 12 Volts Battery Cat # Output Voltage DC011 DC022 DC9000 DC9310 DC9320 DCB095 DCB100 DCB101 DCB102 DCB103 DCB106 DCB107 DCB112 DW911 DW9106 DW9107 DW9108 DW9116 DW9117 DW9118 DW9216 DW9226 DW0246 DCB119 DW0249 DW9109 DC9319 DC9360 DCB361 DC9280 DW0242 DCB200 DCB201 DCB203 DCB204 DCB207 DC9096 DC9099 DC9180 DC9181 D