INSTRUCTION MANUAL DCF813-XE 9.5 mm (3/8") 10.8 V CORDLESS IMPACT WRENCH DCF815-XE 6.35 mm (1/4") 10.
Vibration total values (triax vector sum) determined according to EN 60745: Definitions: Safety Guidelines Vibration emission value ah ah = Uncertainty K = The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits, etc.
V ......................volts Hz ....................hertz min ..................minutes or DC.....direct current ...................Class I Construction ........................(grounded) ...................Class II Construction ........................(double insulated) …/min .............per minute BPM .................beats per minute RPM.................revolutions per minute sfpm ................
• Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack. WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result. CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable batteries. Other types of batteries may burst causing personal injury and damage.
2. Insert the battery pack (F) into the charger, as shown in Figure 1, making sure the pack is fully seated in charger. The red (charging) light will blink continuously indicating that the charging process has started. 3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. • Do not operate charger with damaged cord or plug.
Charge Indicators PROBLEM POWER LINE (DCB100-XE, DCB105-XE) Some chargers have a problem powerline indicator. When the charger is used with some portable power sources such as generators or sources that convert DC to AC, the charger may temporarily suspend operation, flashing the red light with two fast blinks followed by a pause. This indicates the power source is out of limits. Some chargers are designed to detect certain problems that can arise with battery packs.
FIG. 2 WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric shock may result. CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service centre for recycling. G C D Storage Recommendations J 1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. 2.
ASSEMBLY AND ADJUSTMENTS FIG. 3 WARNING: To reduce the risk of serious personal injury, place the forward/ reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. E F Belt Hook (Optional Accessory) To remove the battery pack from the tool, press the release button (E) and firmly pull the battery pack out of the tool handle.
NOTE: The worklights are for lighting the immediate work surface and are not intended to be used as a flashlight. To install an accessory on the hog ring anvil, firmly push accessory onto the anvil (J). The hog ring (K) compresses to allow the accessory to slide on. After the accessory is installed, the hog ring applies pressure to help provide accessory retention. To remove a accessory, grasp the accessory and firmly pull it off. Quick-Release Bit Holder (Fig.
MAINTENANCE WARNING: To reduce the risk of serious personal injury, place the forward/ reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. Lubrication Your power tool requires no additional lubrication. Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
DEWALT BATTERY AND CHARGER SYSTEMS Cat. Number Voltage Amp Hour DCB360 DCB361 DC9360 DE0240-XJ DW0242 DW0240 DC9096 DC9180 DCB180 DCB181 DCB182 DCB183 DCB184 DCB185 DW9096 DE9095-XJ DC9091 DC9144 DCB140 DCB141 DCB142 DCB143 DCB144 DCB145 DE9094 DE9091-XJ DW9091 DC9071 DE9071-XJ DE9074-XJ DW9050 DW9071 DW9072 DCB120 DCB123 DCB125 DCB127 DW9063 DW9062 DW9061 DW9048 DCB080 DW9057 DW9046 Chargers/Charge Time Output Nominal Battery 36 36 36 24 24 24 18 18 18 18 18 18 18 18 18 18 14.4 14.4 14.4 14.4 14.