INSTRUCTION MANUAL DCF880-XE CORDLESS 13 mm (1/2") IMPACT WRENCH DCF835-XE, DCF885-XE CORDLESS 6.
Vibration total values (triax vector sum) determined according to EN 60745: Vibration emission value ah ah = m/s² 15.5 11 Uncertainty K = m/s² 2.2 4.9 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits, etc.
• The label on your tool may include the following symbols. The symbols and their definitions are as follows: V ................. volts A ...............amperes Hz ............... hertz W ..............watts min ............. minutes ...........alternating current ........ direct current ...........alternating or direct current no ..............no load speed .............. Class I Construction ................... (grounded) n................rated speed .............. Class II Construction .............
• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40 °C (105 °F) (such as outside sheds or metal buildings in summer). For best life store battery packs in a cool, dry location. NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never tape the trigger switch in the ON position. WARNING: Fire hazard. Never attempt to open the battery pack for any reason.
• When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
4. If the battery pack does not charge properly: a. Check operation of receptacle by plugging in a lamp or other appliance; b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights; c. Move the charger and battery pack to a location where the surrounding air temperature is approximately 18 ° – 24 °C (65 °F and 75 °F); d. If charging problems persist, take the tool, battery pack and charger to your local service center. 5.
COMPONENTS (FIG. 2) INTENDED USE These impact wrench/drivers are designed for professional impact screwdriving applications. The impact function makes this tool particularly useful for driving fasteners in wood, metal and concrete. DO NOT use under wet conditions or in presence of flammable liquids or gases. These heavy-duty impact wrench/drivers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.
Installing and Removing the Battery Pack (Fig. 3) FIG. 3 NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application. For more information regarding fuel gauge battery packs, please contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ). 0800 339 258. E Variable Speed Trigger Switch (Fig.
FIG. 4 To remove an accessory, depress the detent pin through the hole and pull the accessory off. FIG. 5 C D C Usage D Your impact tool can generate the following output torque: Cat # Ft.-Lbs. In.-Lbs. Nm DCF835-XE 111 1330 150 DCF880-XE 150 1800 203 DCF885-XE 114 1400 155 CAUTION: Ensure fastener and/or system will withstand the level of torque generated by the tool. Excessive torque may cause breakage and possible personal injury. 1. Place the accessory on the fastener head.
Lubrication WARNING: Use only impact accessories. Non-impact accessories may break and cause a hazardous condition. Inspect accessory prior to use to ensure that it contains no cracks. Your power tool requires no additional lubrication. Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear AS/NZS1337 approved eye protection when performing this.
DEWALT BATTERY AND CHARGER SYSTEMS Battery Output Nominal Chargers/Charge Time 230 Volts 12 Volts Cat.