If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos. 1-800-4-DEWALT • www.dewalt.com INSTRUCTION MANUAL GUIDE D'UTILISATION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
English 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.
• Use extra caution when cutting overhead and pay particular attention to overhead wires which may be hidden from view. Anticipate the path of falling branches and debris ahead of time. • Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use. WARNING: ALWAYS use safety glasses.
English Important Safety Instructions for All Battery Packs WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use.
The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate that the costs to recycle these batteries (or battery packs) at the end of their useful life have already been paid by DEWALT.
English will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. CAUTION: Burn hazard.
3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. Charge Indicators Some chargers are designed to detect certain problems that can arise with battery packs. Problems are indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack into the charger. If the problem persists, try a different battery pack to determine if the charger is OK.
English Important Charging Notes there is no battery pack in the cavity. Unplug charger before attempting to clean. 6. Do not freeze or immerse charger in water or any other liquid. WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric shock may result. CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling. 1.
Variable Speed Trigger Switch (Fig. 2, 3) To turn the tool on, squeeze the variable speed trigger switch (A). To turn the tool off, release the variable speed trigger switch. The trigger switch enables you to start the application at a slow speed. The further you depress the trigger, the faster the tool will operate. WARNING: This tool has no provision to lock the switch in the on position and should never be locked on by any other means.
English OPERATION Installing and Removing the Battery Pack (Fig. 5) WARNING: To reduce the risk of serious personal injury, lock the trigger switch and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. WARNING: To reduce the risk of injury, never depress the battery release button without removing the battery pack.
FIG. 6 FIG. 7 FIG. 8 English C Blade Installation and Removal (Fig. 8, 9A, 9B, 9C) WARNING: To reduce the risk of serious personal injury, lock the trigger switch and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. Different blade lengths are available. Use the appropriate blade for the application.
FIG. 9A held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage. Any cuts which put pressure on the blade such as angle or scroll cuts increase potential for vibration, kickback, and blade breakage. WARNING: Use extra caution when cutting overhead and pay particular attention to overhead wires which may be hidden from view. Anticipate the path of falling branches and debris ahead of time.
Next, tip the saw backward FIG. 11 until the back edge of the shoe is resting on the work surface POSITION 2 and the blade clears the work surface (Fig. 11, position 1). Then, squeeze the trigger switch and allow saw to come up to speed. Grip saw firmly with both hands and begin a POSITION 1 slow, deliberate upward swing with the handle of the saw, keeping the bottom of the shoe firmly in contact with the workpiece (Fig. 11, position 2). Blade will begin to feed into material.
English MAINTENANCE Repairs WARNING: To reduce the risk of serious personal injury, lock the trigger switch and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. The charger and battery pack are not serviceable. There are no serviceable parts inside the charger or battery pack.
English DEWALT BATTERY PACKS Product warranty voided if the battery pack is tampered with in any way. DEWALT is not responsible for any injury caused by tampering and may prosecute warranty fraud to the fullest extent permitted by law. 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.
CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES DIRECTIVES POUR UN USAGE ULTÉRIEUR Français Définitions : lignes directrices en matière de sécurité Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces symboles. DANGER : indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves.
d) e) f) g) 3) SÉCURITÉ PERSONNELLE a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention en utilisant un outil électrique peut entraîner des blessures corporelles graves. b) Utiliser des équipements de protection individuelle. Toujours porter une protection oculaire.
Français d) Ranger les outils électriques hors de la portée des enfants et ne permettre à aucune personne n’étant pas familière avec un outil électrique ou son mode d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains d’utilisateurs inexpérimentés. e) Entretien des outils électriques.
19 Français Le risque associé à ces expositions varie selon la fréquence de ces types de travaux. Pour réduire l’exposition aux produits chimiques : travailler dans un local bien ventilé et utiliser du matériel de sécurité approuvé, comme les masques antipoussières spécialement conçus pour filtrer les particules microscopiques. • Éviter le contact prolongé avec la poussière provenant du ponçage, du sciage, du meulage et du forage mécanique ainsi que d’autres activités de construction.
... courant continu ........ Classe I fabrication ............ (mis à la terre) ........ fabrication Classe II ............ (double isolation) …/min .. par minute IPM ...... impacts par minute • Recharger les blocs-piles exclusivement dans des chargeurs DEWALT. • NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau ou dans tout autre liquide.
qu’elles ne soient correctement protégées contre tout court-circuit. Aussi lors du transport individuel de piles, s’assurer que leurs bornes sont bien protégées et isolées de tout matériau pouvant entrer en contact avec elles et provoquer un court-circuit. CONSIGNES DE SÉCURITÉ PROPRES AUX PILES AU LITHIUM-ION (Li-Ion) • Ne pas incinérer le bloc-piles même s’il est sévèrement endommagé ou complètement usagé, car il pourrait exploser et causer un incendie.
Français • Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG, American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus le calibre est petit, et plus sa capacité est grande. Un calibre 16, par exemple, a une capacité supérieure à un calibre 18. L’usage d’une rallonge de calibre insuffisant causera une chute de tension qui entraînera perte de puissance et surchauffe.
• Ne pas utiliser le chargeur s’il a reçu un coup, fait une chute ou a été endommagé de quelque façon que ce soit. Le ramene r dans un centre de réparation agréé. • Ne pas démonter le chargeur. Pour tout service ou réparation, le rapporter dans un centre de réparation agréé. Le fait de le réassembler de façon incorrecte comporte des risques de chocs électriques, d’électrocution et d’incendie. • Débrancher le chargeur du secteur avant tout entretien. Cela réduira tout risque de chocs électriques.
ambiante est élevée comme dans un hangar métallique ou une remorque non isolée. 3. Si le bloc-piles ne se recharge pas correctement : a. Vérifier le bon fonctionnement de la prise en y branchant une lampe ou tout autre appareil électrique. b. Vérifier que la prise n’est pas contrôlée par un interrupteur qui coupe le courant lorsqu’on éteint les lumières. c. Déplacer le chargeur et le bloc-piles dans un local où la température ambiante se trouve entre environ 18 ˚ et 24 ˚C (65 ˚F et 75 ˚F). d.
ATTENTION : ne jamais tenter d’ouvrir le bloc-piles pour quelque raison que ce soit. Si le boîtier plastique du bloc-piles est brisé ou fissuré, le retourner dans un centre de réparation pour y être recyclé. G FIG. 2 Recommandations de stockage 1. Le lieu idéal de rangement est un lieu frais et sec, à l’abri de toute lumière solaire directe et de toute température excessive. 2.
USAGE PRÉVU La scie alternative a été conçue pour la découpe professionnelle des bois, métaux, plastiques et placoplâtres. NE PAS les utiliser en milieu ambiant humide ou en présence de liquides ou de gaz inflammables. Cette scie alternative est un outil électrique de professionnels. NE PAS la laisser à la portée des enfants. Une supervision est nécessaire auprès de tout utilisateur non expérimenté. BOUTON DE VERROUILLAGE Votre scie est équipée d’un bouton de verrouillage (B).
Position correcte des mains (Fig. 2, 4) Glissière de libération du pivot (Fig. 2, 6, 7) AVERTISSEMENT : pour réduire tout risque de dommages corporels graves, adopter SYSTÉMATIQUEMENT la position des mains illustrée. AVERTISSEMENT : pour réduire tout risque de dommages corporels graves, maintenir fermement et SYSTÉMATIQUEMENT l’outil pour anticiper toute réaction soudaine de sa part. La position correcte des mains requiert une main sur la poignée de saisie (I), et l’autre sur la poignée principale (H).
4. Remarque : la lame peut être installée à l’envers pour effectuer une coupe à ras (se reporter à la fig. 9B). Il existe différentes longueur de lames. Utiliser la lame appropriée au travail en cours. La longueur de la lame doit être supérieure à 89 mm (3-1/2") et dépasser la grandeur du patin et l’épaisseur de la pièce à découper. Pour des performances optimales, il est recommandé d’utiliser une lame de 102 mm (4 po). Ne pas utiliser de lames à scie sauteuse avec cet outil.
REMARQUE : les lampes de travail servent à éclairer la surface immédiate de travail et n’ont pas été conçues pour être utilisées en tant que lampe torche. SCIAGE AU-RAS (FIG. 9B, 10) FIG. 10 La forme compacte du boîtier du moteur et de la broche permet des coupes extrêmement précises des planchers, coins et tout autre endroit délicat. La lame devrait être insérée à l’envers pour permettre une coupe à ras (Fig. 9B, 10). Sciage (Fig. 9, 10–13) COUPES INTERNE/EN PLONGÉE – BOIS SEULEMENT (FIG.
Mode horizontal : les dents de scie sont orientées vers le bas comme illustré en figure 13A. Mode vertical : les dents de scie sont orientées vers l’avant comme illustré en figure 13B. La DCS310 peut accepter toute sorte de longueurs de lames alternatives. Pour des résultats optimums, utilisez des lames de 102 mm (4 po). Pendant la coupe, assurez-vous que la lame aille au-delà du patin et de l’épaisseur de la pièce à découper. Le cas échéant, utilisez une longueur supérieure de lame.
Nettoyage Réparations AVERTISSEMENT : enlever les saletés et la poussière hors des évents au moyen d’air comprimé propre et sec, au moins une fois par semaine. Pour minimiser le risque de blessure aux yeux, toujours porter une protection oculaire conforme à la norme ANSI Z87.1 lors du nettoyage. AVERTISSEMENT : ne jamais utiliser de solvants ni d’autres produits chimiques puissants pour nettoyer les pièces non métalliques de l’outil.
REMPLACEMENT GRATUIT DES ÉTIQUETTES D’AVERTISSEMENT : si les étiquettes d’avertissement deviennent illisibles ou sont manquantes, composer le 1 800 433-9258 (1 800 4-DEWALT) pour en obtenir le remplacement gratuit.
CONSERVE TODAS LAS ADVERTENCIAS E INSTRUCCIONES PARA FUTURAS CONSULTAS Definiciones: Normas de seguridad Las siguientes definiciones describen el nivel de gravedad de cada palabra de señal. Lea el manual y preste atención a estos símbolos. PELIGRO: Indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves. ADVERTENCIA: Indica una situación de peligro potencial que, si no se evita, podría provocar la muerte o lesiones graves.
Español c) No exponga las herramientas eléctricas a la lluvia o a condiciones de humedad. Si entra agua a una herramienta eléctrica, aumentará el riesgo de descarga eléctrica. d) No maltrate el cable. Nunca utilice el cable para transportar, tirar o desenchufar la herramienta eléctrica. Mantenga el cable alejado del calor, el aceite, los bordes filosos y las piezas móviles. Los cables dañados o enredados aumentan el riesgo de descarga eléctrica.
c) d) e) f) 5) USO Y MANTENIMIENTO DE LA HERRAMIENTA CON BATERÍAS a) Recargue solamente con el cargador especificado por el fabricante. Un cargador adecuado para un tipo de paquete de baterías puede originar riesgo de incendio si se utiliza con otro paquete de baterías. b) Utilice herramientas eléctricas sólo con paquetes de baterías específicamente diseñados. El uso de cualquier otro paquete de baterías puede producir riesgo de incendio y lesiones.
Español Normas específicas de seguridad adicionales para sierras de vaivén ADVERTENCIA: Use SIEMPRE lentes de seguridad. Los anteojos de uso diario NO son lentes de seguridad. Utilice también máscaras faciales o para polvo si el corte produce polvillo. UTILICE SIEMPRE EQUIPOS DE SEGURIDAD CERTIFICADOS: • Protección para los ojos ANSI Z87.1(CAN/CSA Z94.3), • Protección auditiva según la norma ANSI S12.6 (S3.19), • Protección respiratoria según las normas NIOSH/OSHA/ MSHA.
Instrucciones de seguridad importantes para todas las unidades de batería ADVERTENCIA: Toda persona que entre al área de trabajo deberá usar una máscara antipolvo o protección respiratoria. El filtro debería ser reemplazado a diario o cuando el usuario tenga dificultad para respirar. Puede encontrar la máscara antipolvo apropiada aprobada por NIOSH/OSHA en su ferretería local. ADVERTENCIA: Durante el uso, use siempre protección auditiva adecuada que cumpla con la norma ANSI S12.6 (S3.19).
Español o un cargador que haya sido golpeado, dejado caer, atropellado o dañado en cualquier forma (es decir, perforado por un clavo, golpeado con un martillo, pisado). Lleve sus unidades de batería dañadas a un centro de servicio para que sean recicladas. ADVERTENCIA: Peligro de incendio. No guarde ni transporte la batería de manera que objetos metálicos puedan hacer contacto con los terminales expuestos de la batería.
GUARDE ESTAS INSTRUCCIONES: Este manual contiene instrucciones de seguridad y operación importantes para los cargadores de baterías. • Antes de usar el cargador, lea todas las instrucciones y advertencias que se encuentren en el cargador, la unidad de batería y el producto que usa la unidad de batería. ADVERTENCIA: Peligro de descarga eléctrica. No permita que ningún líquido se introduzca en el cargador. Puede producir descargas eléctricas. ATTENCIÓN: Peligro de quemaduras.
Cargadores Calibre mínimo para cables de alimentación Voltios Largo total del cable en metros (en pies) Amperaje Español Desde Hasta 0 6 6 10 10 12 12 16 120 V 7,6 (25) 240 V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300) AWG 18 16 16 14 18 16 14 12 16 16 14 12 14 12 No recomendado 15,2 (50) Su herramienta utiliza un cargador DEWALT. Asegúrese de leer todas las instrucciones de seguridad antes de usar el cargador.
la unidad de batería es defectuosa al no iluminarse o al indicar que existe un problema con la unidad o el cargador. NOTA: Esto también puede significar que hay un problema con el cargador Indicadores de carga Algunos cargadores fueron diseñados para detectar ciertos problemas que pueden surgir con las unidades de batería. Estos problemas se indican mediante una luz roja intermitente rápida. Si esto ocurre, vuelva a colocar la unidad de batería en el cargador.
estas circunstancias. Siga el procedimiento de carga. También puede cargar una unidad de batería que haya sido usada parcialmente cuando lo desee, sin dañarla. 5. Los materiales ajenos conductores por naturaleza, tales como, pero sin limitarse a, el polvo del esmerilado, las virutas metálicas, la lana de acero, el papel de aluminio o cualquier acumulación de partículas metálicas deberían mantenerse alejados de las cavidades del cargador.
A. Interruptor tipo gatillo de velocidad variable B. Botón de bloqueo de encendido C. Control deslizante de liberación del pivote D. Base E. Luz de trabajo LED BOTÓN DE BLOQUEO DE ENCENDIDO La sierra viene equipada con un botón de bloqueo de encendido (B). Para bloquear el interruptor tipo gatillo (A), oprima el botón de bloqueo de encendido como lo muestra la Figura 3. Cuando se aprieta el botón de bloqueo de encendido hasta alcanzar el ícono con el candado, la herramienta queda bloqueada.
sin retirar la unidad de batería, ésta podría caerse inesperadamente de su lugar. NOTA: Para mejores resultados, verifique que su unidad de batería esté completamente cargada. Para instalar la unidad de batería (J) en el mango de la herramienta, alinee la unidad de batería con los rieles en el interior del mango de la herramienta y deslícela en el mango hasta que la unidad de batería quede firmemente insertada en la herramienta; verifique que ésta no se salga sola.
empuñadura de la herramienta hasta que la escuche entrar bien en cualquiera de las tres posiciones que aparecen en la Figura 7. FIG. 6 FIG. 8 FIG. 7 C Instalación y extracción de la hoja (Fig. 8, 9A, 9B, 9C) ADVERTENCIA: Para reducir el riesgo de lesiones corporales graves, bloquee el interruptor tipo gatillo y desconecte la unidad de batería antes de realizar ajustes o de quitar o poner accesorios. Un arranque accidental puede causar lesiones. Hay diferentes longitudes de hojas disponibles.
2. Saque la hoja. FIG. 9A Antes de cortar cualquier tipo de material, asegúrese que está firmemente anclado o sujeto con abrazaderas para prevenir que se corra. Ponga la hoja ligeramente sobre la pieza que será cortada, encienda el motor de la sierra y permita que alcance su velocidad máxima antes de aplicar presión. Cuando sea posible, la base metálica de la sierra deberá ser sostenida firmemente contra el material que se está cortando.
CORTE DE METALES (FIG. 12) Su sierra tiene diferentes capacidades de corte de metal, dependiendo del tipo de hoja utilizado y el metal a cortar. Use una hoja más fina para metales férreos y una más gruesa para materiales no-férreos. Para metales en láminas de calibres finos, es mejor colocar un pedazo de madera en cada lado de la lámina y sujetarlo a ella con abrazaderas. Esto garantizará un corte limpio sin vibración excesiva o desgarramiento del metal.
La DCS310 es compatible con hojas de vaivén de cualquier longitud. Para mejores resultados, utilice hojas de 102 mm (4 pulg.). Verifique que la hoja sobrepase la base y el espesor de la pieza de trabajo durante el corte. Use una hoja más larga si es necesario. Siempre que se pueda, la base de la sierra deberá ser sujetada con firmeza contra el material a cortar. Esto evitará que la sierra salte o vibre, y minimizará las posibilidades de rotura de la hoja. FIG.
inspección y cambio de carbones) ser realizados en un centro de mantenimiento en la fábrica DEWALT, en un centro de mantenimiento autorizado DEWALT u por otro personal de mantenimiento calificado. Utilice siempre piezas de repuesto idénticas. VILLAHERMOSA, TAB Constitución 516-A - Col. Centro (993) 312 5111 PARA OTRAS LOCALIDADES: Si se encuentra en México, por favor llame al (55) 5326 7100 Si se encuentra en U.S.
gastados por la clavadora, tales como la unidad de hoja y retorno del impulsador, no están cubiertas. EXCEPCIONES Esta garantía no será válida en los siguientes casos: • Cuando el producto se hubiese utilizado en condiciones distintas a las normales; • Cuando el producto no hubiese sido operado de acuerdo con el instructivo de uso que se acompaña; • Cuando el producto hubiese sido alterado o reparado por personas distintas a las enlistadas al final de este certificado.
REEMPLAZO GRATUITO DE LAS ETIQUETAS DE ADVERTENCIAS: Si sus etiquetas de advertencia se vuelven ilegibles o faltan, llame al 1-800-4-DEWALT (1-800-433-9258) para que se le reemplacen gratuitamente. SOLAMENTE PARA PROPÓSITO DE MÉXICO: IMPORTADO POR: BLACK & DECKER S.A. DE C.V. AVENIDA ANTONIO DOVALI JAIME, # 70 TORRE B PISO 9 COLONIA LA FE, SANTA FÉ CÓDIGO POSTAL : 01210 DELEGACIÓN ALVARO OB REGÓN MÉXICO D.F. TEL. (52) 555-326-7100 R.F.C.
DEWALT Battery and Charger Systems Battery Output Cat # Chargers/Charge Time (Minutes) – Chargeurs/Durée de charge (Minutes) – Cargadores de baterías/Tiempo de carga (Minutos) 120 Volts 12 Volts Voltage DW9106 DW9118 DW9107 DW9108 DW9116 DW9216 DW9117 DW911 DC011 DC022 DC9000 DC9310 DC9320 DCB100 DCB101 DCB103 DW0246 DCB119 DW0249 DW9109 DC9319 DC9360 36 X X X X X X X X X X 60 X X X X X X X X X X DC9280 DW0242 DC9096 DC9099 DC9180 DC9181 DCB200 DCB201 DW909