User Manual
12
ENGLISH
Inserting and Removing the Battery Pack
from the Tool (Fig.B)
NOTE: Make sure your battery pack
11
is fullycharged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
11
with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the release button
12
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig.B)
Some
DeWALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge
button
16
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑userapplication.
Cutting Action—Orbital or Straight (Fig.F)
This jig saw is equipped with four cutting actions, three orbital
and one straight. Orbital action has a more aggressive blade
motion and is designed for cutting in soft materials like wood
or plastic. Orbital action provides a faster cut, but with a less
smooth cut across the material. In orbital action, the blade
moves forward during the cutting stroke in addition to the up
and downmotion.
NOTE: Metal or hardwoods should never be cut in orbitalaction.
To adjust the cutting action, move the orbital action lever
6
between the four cutting positions: 0, 1, 2, and 3. Position 0is
straight cutting. Positions 1, 2, and 3are orbital cutting. The
aggressiveness of the cut increase as the lever is adjusted from
one to three, with three being the most aggressivecut.
Beveling the Shoe (Fig.E)
To Bevel the Shoe
1. Remove the dust extraction accessories if they are mounted
to the tool as the tool will not bevel if they are attached.
Refer to Dust Extractionsection.
2. Unlock the shoe by pulling the shoe bevel lever
8
to
theside.
3. Slide the shoe
7
forward to release it from the 0° positive
stopposition.
NOTE: The shoe can be beveled to the left or to the right
at a maximum of 45° in either direction. There are visible
detents at 15° and 30°.
4. Once the desired bevel angle is achieved, lock the shoe
inposition:
a. For 0° and 45° bevel angles, slide the shoe back and lock
the shoe by moving the bevel lever back under the body
of the jigsaw.
b. For all angles between 0° and 45°, lock with bevel
leveronly.
NOTE: When installing flush cutting blades (DT2074), the
anti‑splinter insert (
12
, Fig. J) must be removed and the shoe
must to be in the 0° positive stopposition.
NOTE: The correct saw blade must be selected for the material
beingcut.
1. Hold open the blade release latch
4
as shown in FigureD.
2. Insert the T‑shank blade into the clamp mechanism
13
while guiding the back of the blade into the groove of the
guide rollers
17
.
3. The T‑shank should be completely inside the
clampmechanism.
4. Release the blade releaselatch.
To Remove a Blade
CAUTION: Do not touch used blades, they may be hot.
Personal injury mayresult.
1. Hold open the blade release latch
4
.
2. With a slight shake the blade will dropout.
3. Release the blade releaselatch.
Blade Installation and Removal (Fig.D, J)
To Install a Blade
NOTE: This jig saw uses only T‑shank jig sawblades.
NOTE: The DT2074 flush cutting blade is for use with D
e
WALT
DCS334 and DCS335 jig sawsonly.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
WARNING: Use only
DeWALT
battery packs andchargers.
These heavy‑duty jigsaws are professional powertools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision. (XE requirement ‑ English only)
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.