Instruction Manual Guide D’utilisation Manual de instrucciones DCS369 20V Max* Compact Reciprocating Saw Scie alternative compacte 20 V max* Sierra Recíproca Compacta 20 V Máx* If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos.
English (original instructions) 1 Français (traduction de la notice d’instructions originale) 13 Español (traducido de las instrucciones originales) 27
English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
English 20V Max* Compact Reciprocating Saw DCS369 GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
English that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g ) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
English • • • lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemicallytreated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
English • battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention. WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame. WARNING: Fire hazard.
English 120V Max* (two 60V Max* batteries) product, it will operate as a 60V Max* battery. Shipping Mode: When the cap is attached to the FLEXVOLT™ battery, the battery is in Shipping Mode. Strings of cells are electrically disconnected within the pack resulting in three batteries with a lower Watt hour (Wh) rating as compared to one battery with a higher Watt hour rating.
English CAUTION: Burn hazard. To reduce the risk of injury, charge only DeWALT rechargeable battery packs. Other types of batteries may overheat and burst resulting in personal injury and property damage. CAUTION: Under certain conditions, with the charger plugged into the power supply, the charger can be shorted by foreign material.
English Charger Cleaning Instructions WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. 3. Release blade clamp. Gently tug on the blade to ensure blade is clamped securely. NOTE: Blade can be installed upside-down to assist in flush‑to cutting. Fig.
English Fig. C 13 12 Proper hand position requires one hand on the main handle 8 and one hand the hand grip 5 or one hand on the main handle with the material being cut properly clamped. Fig. E 5 OPERATION 8 WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. Installing and Removing the Battery Pack (Fig.
English Flush Cutting (Fig. H) Fig. F The compact design of the reciprocating saw motor housing and pivoting shoe permit close cutting to floors, corners and other difficult areas. 1. To maximize flush cutting capabilities, insert the blade shaft into the blade clamp with the teeth of the blade facing up. 2. Turn the saw upside down so you are as close to the work surface as possible. 2 Fig. H 1 Hang Cleat (Fig.
English NOTE: You should spread a thin film of oil or other coolant along the line ahead of the saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred. Fig. J MAINTENANCE WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. Cleaning Pocket Cutting - Wood Only (Fig.
English Three Year Limited Warranty DeWALT will repair or replace, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase (two years for batteries). This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DeWALT (1-800-433-9258).
Français Définitions : symboles et termes d'alarmes sécurité Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations dangereuses et de risques de dommages corporels ou matériels. DANGER : indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves.
Français Scie alternative compacte 20 V max* DCS369 AVERTISSEMENTS GÉNÉRAUX SUR LA SÉCURITÉ DES OUTILS AVERTISSEMENT : lisez tous les avertissements de sécurité, toutes les instructions, les illustrations et les caractéristiques fournis avec cet outil électrique. Ne pas suivre toutes les instructions comprises aux présentes peut conduire à un choc électrique, un incendie et/ou des blessures graves.
Français sécurité de l’outil. Un acte irréfléchi peut causer une blessure grave en une fraction de seconde. c) 4) Utilisation et entretien d’un outil électrique a ) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application. L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle il a été conçu. b ) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux.
Français AVERTISSEMENT : ne pas utiliser cet outil durant de longues périodes. La vibration causée par l’action du fonctionnement de cet outil peut causer des blessures permanentes aux doigts, mains et aux bras. Utilisez des gants pour offrir un coussin supplémentaire, prenez des pauses fréquentes et limitez la durée d’utilisation quotidienne.
Français ...................... symbole d’avertissement ...................... radiation visible ...................... protection respiratoire IPXX..................... symbole IP ...................... protection oculaire ...................... protection auditive ...................... lire toute la documentation • • BLOCS-PILES ET CHARGEURS Le bloc-piles n’est pas totalement chargé d’usine.
Français Le témoin de charge indique approximativement le niveau de charge restant dans le bloc-piles en fonction des voyants suivants : Chargé de 75 à 100 % Chargé de 51 à 74 % Chargé de < 50 % Le bloc-piles doit être rechargé Pour activer le témoin de charge, maintenez appuyé le bouton du témoin de charge. Une combinaison des trois voyants Del s’allumera indiquant le niveau de charge.
Français Directives de sécurité importantes propres à tous les chargeurs de piles • • • • • • • • AVERTISSEMENT : lisez toutes les consignes de sécurité, les instructions et les symboles d’avertissements du bloc-piles, du chargeur et du produit. Tout manquement aux avertissements et instructions pose des risques de décharges électriques, d’incendie et/ou de blessures graves. NE PAS tenter de recharger le bloc-piles avec tout autre chargeur qu’une unité DeWALT.
Français (mais pas limité à) poussières de rectification, débris métalliques, laine d’acier, feuilles d’aluminium, ou toute accumulation de particules métalliques doivent être maintenus à distance des orifices du chargeur. Débrancher systématiquement le chargeur lorsque le bloc-piles n’y est pas inséré. Débrancher systématiquement le chargeur avant tout entretien.
un bloc-piles partiellement déchargé sans effet nuisible sur le bloc-piles. 5. Les corps étrangers conducteurs tels que (mais pas limité à) poussières de rectification, débris métalliques, laine d’acier, feuilles d’aluminium, ou toute accumulation de particules métalliques doivent être maintenus à distance des orifices du chargeur. Débrancher systématiquement le chargeur lorsque le bloc-piles n’y est pas inséré. Débrancher systématiquement le chargeur avant tout entretien. 6.
Français en position verrouillée afin d’éviter un démarrage non intentionnel. MPORTANT : pour rattacher ou remplacer le crochet de ceinture 12 , utiliser systématiquement la vis 13 fournie à cet effet. S’assurer de resserrer fermement la vis. L’agrafe pour courroie 12 peut être fixée sur un côté ou l’autre de l’outil utilisant seulement la vis fournie 13 pour accommoder les utilisateurs droitiers ou gauchers. Si vous ne voulez pas du tout de l’agrafe pour courroie, vous pouvez la retirer de l’outil.
Français Gâchette à vitesse variable (Fig. A, F) Fig. G Bouton de Verrouillage et Gâchette Votre scie est équipée d’un bouton de verrouillage 2 . Pour verrouiller la gâchette, appuyez sur le bouton de verrouillage à gauche. Toujours verrouiller la gâchette 1 avant de transporter ou ranger l’outil pour éliminer tout démarrage accidentel. Pour déverrouiller la gâchette, appuyez sur le bouton de verrouillage à droite. Pousser la gâchette pour mettre le moteur en marche.
Français Fig. H Fig. J Découpe en poche – bois seulement (Fig. K) Coupe du bois (Fig. I) 1. Avant de couper tout type de bois, s’assurer que la pièce est bien ancrée ou serrée dans un étau pour éviter tout glissement. 2. Appuyer légèrement la lame et la semelle pivotante contre la pièce à couper. 3. Mettre en marche le moteur de la scie avant d’appliquer toute pression. 4. Tenez toujours la scie comme illustré dans la Figure E pendant la coupe.
Français MAINTENANCE AVERTISSEMENT : afin de réduire le risque de blessure corporelle, éteignez l’appareil et retirez le bloc-piles avant d’effectuer tout ajustement ou de retirer/installer des pièces ou des accessoires. Un déclenchement accidentel du démarrage peut causer des blessures. Nettoyage AVERTISSEMENT : enlever les saletés et la poussière hors des évents au moyen d’air comprimé propre et sec, au moins une fois par semaine.
Français REMARQUE : la garantie de se produit sera annulée si le bloc-piles a été altéré de quelque façon que ce soit. DeWALT ne peut être tenu responsable de tout dommage corporel causé par l’altération du produit et pourra poursuivre toute fraude en matière de garantie dans toute l’étendue permise par la loi.
Español Definiciones: Símbolos y Palabras de Alerta de Seguridad Este manual de instrucciones utiliza los siguientes símbolos y palabras de alerta de seguridad para alertarle de situaciones peligrosas y del riesgo de lesiones corporales o daños materiales. PELIGRO: Indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves. ADVERTENCIA: Indica una situación de peligro potencial que, si no se evita, podría provocar la muerte o lesiones graves.
Español Sierra Recíproca Compacta 20 V Máx* DCS369 ADVERTENCIAS GENERALES DE SEGURIDAD PARA HERRAMIENTAS ELÉCTRICAS ADVERTENCIA: Lea todas las advertencias de seguridad, instrucciones, ilustraciones y especificaciones incluidas con esta herramienta eléctrica. La falla en seguir todas las instrucciones siguientes puede resultar en descarga eléctrica, incendio y/o lesiones serias.
Español h ) No permita que la familiaridad obtenida a partir del uso frecuente de herramientas le permitan volverse descuidado e ignorar los principios de seguridad de la herramienta. Una acción descuidada puede causar lesiones severas en una fracción de segundo. 4) Uso y Mantenimiento de la Herramienta Eléctrica a ) No fuerce la herramienta eléctrica. Utilice la herramienta eléctrica correcta para el trabajo que realizará.
Español Instrucciones de Seguridad para Sierras Recíprocas • • Sujete la herramienta eléctrica de sus superficies aislantes cuando lleve a cabo una operación en que el accesorio de corte pudiera entrar en contacto con un hilo eléctrico oculto. Los accesorios de corte que entren en contacto con un hilo eléctrico activo podrían hacer que las partes metálicas de la herramienta eléctrica también se activen con electricidad y que el operador sufra una descarga eléctrica.
Español La etiqueta de su herramienta puede incluir los siguientes símbolos. A continuación se indican los símbolos y sus definiciones: V.......................... voltios or AC............ corriente alterna Hz........................ hertz or AC/DC..... corriente alterna o directa min...................... minutos ....................... Construcción de or DC....... direct current Clase II (doble ....................... Construcción de aislamiento) Clase I (tierra) n ........................
Español Recomendaciones de Almacenamiento 1. El mejor lugar de almacenamiento es uno que sea fresco y seco, lejos de la luz solar directa y del exceso de calor o frío. 2. Para resultados óptimos durante tiempos prolongados de almacenamiento, se recomienda almacenar la unidad de batería completamente cargada en un lugar fresco y seco fuera del cargador. NOTA: Las unidades de batería no deberían almacenarse completamente descargadas. La unidad de batería deberá recargarse antes de ser usada.
Español con una batería con una capacidad nominal de vatios hora superior. Esta mayor cantidad de tres baterías con una capacidad nominal de vatios-hora menor puede hacer que la unidad de batería quede exenta de ciertos reglamentos de transporte que se imponen a las baterías con mayor capacidad nominal de vatios-hora. La etiqueta en la batería indica dos capacidades nominales de vatios-hora (ver el ejemplo).
Español ADVERTENCIA: Peligro de quemaduras. No sumerja la unidad de batería en líquido de ningún tipo ni permita que se introduzca ningún tipo de líquido a la unidad de batería. Nunca intente abrir la unidad de batería por ningún motivo. Si la caja plástica de la unidad de batería se triza o rompe, llévela a un centro de servicio para su reciclaje. ATENCIÓN: Peligro de quemaduras. Para reducir el riesgo de lesiones, sólo cargue unidades de batería recargables DeWALT marca.
Español b. Revise que la toma de corriente no esté conectada a un interruptor de luz que corte la corriente cuando se corte la luz; c. Mueva el cargador y la unidad de batería a un lugar donde la temperatura ambiental sea aproximadamente 18 °C– 24 °C (65 °F– 75 °F); d. Si el problema de carga continúa, lleve la herramienta, unidad de batería y el cargador a su centro de servicio local. 4.
Español Fig. B Fig. C 13 3 12 11 Para Quitar la Cuchilla de la Sierra (Fig. B) ADVERTENCIA: Riesgo de quemaduras. No toque la cuchilla de inmediato después de usarla. El contacto con la cuchilla puede ocasionar lesiones personales. 1. Gire para abrir la abrazadera de la cuchilla 3 a su posición completamente abierta. 2. Retire la cuchilla 11 . Gancho para Cinturón (Fig.
Español Posición Adecuada de las Manos (Fig. E) ADVERTENCIA: Para reducir el riesgo de lesión personal grave, tenga SIEMPRE las manos en una posición adecuada como se muestra. ADVERTENCIA: Para reducir el riesgo de lesión personal grave, sujete SIEMPRE bien en caso de que haya una reacción repentina. La posición adecuada de la mano requiere una mano en la manija principal 8 y una mano en la agarradera 5 o una mano en la manija principal con el material que se corta asegurado adecuadamente. Fig.
Español Corte (Fig. A, B, E) La cuchilla 11 debe extenderse más allá de la zapata ajustable 4 y el espesor de la pieza de trabajo durante el corte. Seleccione la cuchilla más adecuada para el material que desee cortar y utilice la cuchilla más corta apropiada para el espesor del material. No utilice cuchillas de sierra caladora con esta herramienta. NOTA: Antes de cortar cualquier tipo de material, asegúrese de que esté firmemente sujeto o fijo para evitar el deslizamiento.
Español Fig. K 2 1 Los accesorios que se recomiendan para utilizar con la herramienta están disponibles a un costo adicional en su distribuidor local o en un centro de mantenimiento autorizado. Si necesita ayuda para localizar algún accesorio, póngase en contacto com DeWALT, llame al 1-800-4-DeWALT (1-800-433-9258) o visite nuestro sitio web: www.dewalt.com.
Español Si se encuentra en U.S., por favor llame al 1-800-433-9258 (1-800 4-DeWALT) Póliza de Garantía IDENTIFICACIÓN DEL PRODUCTO: Sello o firma del Distribuidor. Nombre del producto: ___________________________ Mod./Cat.: ____________________________________ Marca: ______________________________________ Núm.
la información de la garantía específica del país que viene en el empaque, llamar a la compañía local o visitar el sitio Web a fin de obtener esa información. REEMPLAZO GRATUITO DE LAS ETIQUETAS DE ADVERTENCIAS: Si sus etiquetas de advertencia se vuelven ilegibles o faltan, llame al 1-800-4-DeWALT (1-800-4339258) para que se le reemplacen gratuitamente. ESPECIFICACIONES DCS369 20 V Máx* 0–2800 spm * El máximo voltaje inicial de la batería (medido sin carga de trabajo) es 12, 20, 60 o 120 voltios.
DeWALT BATTERY AND CHARGER SYSTEMS Chargers/Charge Time (Minutes) . Chargeurs/Durée de charge (Minutes) .