® DW007 1
Dansk 6 Deutsch 14 English 23 Español 31 Français 39 Italiano 47 Nederlands 56 Norsk 64 Português 72 Suomi 80 Svenska 88 Türkçe 96 EÏÏËÓÈη 104 Copyright DEWALT 2
1 2 5 3 11 4 8 12 10 6 9 14 15 13 15 7 16 17 A 3
18 15 18 15 B 6 11 C 4 12
23 max 5mm 5mm 4 11 22 21 20 D 9 5
DANSK BATTERIDREVET RUNDSAV DW007K/DW007KH Tillykke! EU-Overensstemmelseserklæring Du har valgt et DEWALT Elværktøj. Mange års erfaring, ihærdig produktudvikling og innovation gør DEWALT til en af de mest pålidelige partnere for professionelle brugere.
DANSK Sikkerhedsinstruktioner Læs brugsanvisningen igennem, inden maskinen tages i brug. Opbevar brugsanvisningen let tilgængeligt, så alle, der bruger maskinen, har adgang til brugsanvisningen. Foruden nedenstående instruktioner, bør Arbejdstilsynets regler altid følges. ADVARSEL! Når man anvender elværktøj, skal følgende grundlæggende sikkerhedsinstruktioner altid følges for at nedsætte risikoen for elektriske stød, personskader og brand.
DANSK 18 Få dit værktøj repareret hos et autoriseret DEWALT serviceværksted Dette elværktøj overholder de relevante sikkerhedsforskrifter. For at undgå fare, må reparationer af eludstyr kun foretages af autoriserede serviceværksteder. Yderligere sikkerhedsanvisninger for batterier og ladere Brandrisiko! Undgå metalkortslutning af elektroderne på en fritliggende batteripakke. Man må ikke opbevare eller transportere batteripakken, uden at den medfølgende beskyttelseshætte er sat på elektroderne.
DANSK • Spaltekniven skal indstilles korrekt. Afstanden mellem den tandede kant og spaltekniven må højst være 5 mm og højdeforskellen mellem spaltekniven og den tandede kant må højst være 5 mm. Kontrol og udskiftning af savklingen • Der må kun anvendes savklinger, der opfylder de i denne brugsanvisning angivne specifikationer. • Der bør ikke anvendes savklinger, hvis hoveddel er tykkere eller hvis deling er mindre end spalteknivens tykkelse. • Brug kun skarpe savklinger i perfekt tilstand.
DANSK Udskiftning af kabel eller stik Ved udskiftning af kablet eller af stikket skal den bortskaffes på sikker måde. Et stik med blottede kobberledere er farlig, hvis den sættes i en strømførende kontakt. Samling og justering • Før samlingen og justeringen skal batteriet altid afmonteres. • Afbryd altid værktøjet før indsættelse eller udtagning af batteriet. • Sørg for at batteriet er korrekt placeret før brug af værktøjet. Kun brug DEWALT batterier og lader. Batteri (fig.
DANSK AIR COOLED Denne oplader er udstyret med en indvendig ventilator, så batterierne hurtigt kan afkøles. Ventilatoren tændes automatisk, når det er nødvendigt. Ventilatoren bliver også sat til med mellemrum, når der ikke er batteri i opladeren, for at blæse støv af ventilatorvingerne. Brug altid sikkerhedsbriller når laderen tilsluttes. • Træk den nedre klingeafskærmning tilbage ved hjælp af håndtaget (11) og udskift klingen (21). Monter skiverne (20 & 22) på de korrekte steder.
DANSK Start eller stop ikke maskinen, når savklingen rører ved arbejdsemnet eller ved andre materialer. Hvordan man holder og styrer værktøjet (fig. A) • Hold på værktøjet ved at gribe godt fat om hovedhåndtaget og det forreste håndtag (3) for at kunne styre saven ordentligt. • Da snittet bliver glattere på den side, hvor savklingen efterlader arbejdsemnet, bør dette spændes fast så bagsiden vender mod klingen. • Brug indikatoren for savspor (7) til at følge den tegnede linie på arbejdsemnet.
DANSK GARANTI • 30 DAGE TILFREDS-KUNDE GARANTI • Fuld tilfredshed eller pengene tilbage. Hvis du ikke er helt tilfreds med dit DEWALTværktøj, kan du returnere værktøjet til forhandleren inden 30 dage efter købet og få dine penge refunderet eller værktøjet ombyttet. Værktøjet skal indleveres komplet, og købsnotaen skal forevises.
DEUTSCH AKKU-HANDKREISSÄGE DW007K/DW007KH Herzlichen Glückwunsch! Sie haben sich für ein Elektrowerkzeug von DEWALT entschieden, das die lange DEWALT-Tradition fortsetzt, nur ausgereifte und in zahlreichen Tests bewährte Qualitätsprodukte für den Fachmann anzubieten. Lange Jahre der Erfahrung und kontinuierliche Weiterentwicklung machen DEWALT zu Recht zu einem verläßlichen Partner aller professionellen Anwender. Technische Daten Spannung Max. Ausgangsleistung Leerlaufdrehzahl Sägeblattdurchmesser Max.
DEUTSCH Sicherheitshinweise Beim Gebrauch von Elektrowerkzeugen sind zum Schutz gegen elektrischen Schlag, Verletzungs- und Feuergefahr die nationalen Sicherheitsvorschriften zu beachten. Lesen Sie folgende Sicherheitshinweise, bevor Sie das Elektrowerkzeug benutzen. Bewahren Sie diese Sicherheitshinweise gut auf! Allgemeines 1 Halten Sie Ihren Arbeitsbereich in Ordnung Unordnung im Arbeitsbereich führt zu Unfallgefahren. 2 Berücksichtigen Sie Umgebungseinflüsse Setzen Sie Elektrowerkzeuge keiner Nässe aus.
DEUTSCH Beschädigte Teile und Schutzvorrichtungen müssen vorschriftsgemäß repariert oder ausgewechselt werden. Benutzen Sie das Elektrowerkzeug nicht, wenn der Schalter defekt ist. Beschädigte Schalter müssen durch eine DEWALT-Kundendienstwerkstatt ersetzt werden. 16 Entnehmen Sie den Akku Entnehmen Sie den Akku bei Nichtgebrauch, vor der Wartung und beim Werkzeugwechsel.
DEUTSCH • Nach dem Ausschalten der Handkreissäge darf das Sägeblatt niemals durch seitliches Gegendrücken abgebremst werden. • Legen Sie die Handkreissäge grundsätzlich nur in ausgeschaltetem Zustand auf den Arbeitstisch oder die Werkbank ab. Vorrichtungen für einen sicheren Betrieb • Stellen Sie sicher, daß die Handkreissäge ausschließlich zur Holz- und Kunststoffbearbeitung verwendet wird. • Vergewissern Sie sich, daß alle Vorrichtungen, die das Sägeblatt abdecken, einwandfrei funktionieren.
DEUTSCH 10 11 12 13 14 15 Unterer Blattschutz Rückzughebel unterer Blattschutz Schuh Tiefeneinstellung Akku-Löseknopf Akku Ladegerät Ihr Ladegerät DE0246 lädt 24 V NiCd- und NiMH-Akkus von DEWALT. 15 Akku 16 Ladegerät 17 Ladekontrolleuchte (rot) Zusammenbauen und Einstellen • Entnehmen Sie vor dem Zusammenbauen und Einstellen immer den Akku. • Schalten Sie das Elektrowerkzeug immer aus, bevor Sie den Akku einsetzen oder entfernen.
DEUTSCH Automatischer Feinausgleich Beim automatischen Feinausgleich werden die einzelnen Zellen im Batteriepaket sowie deren Spitzenkapazität ausgeglichen. Akkus sollten nach jedem zehnten Lade-/ Entladezyklus bzw. immer, wenn der Akku nicht mehr die gewohnte Leistung liefert, über Nacht ausgeglichen werden. • Um den Akku auszugleichen, legen Sie den Akku wie gewohnt in das Ladegerät. Die rote Kontrolleuchte blinkt ununterbrochen und zeigt damit an, daß der Ladezyklus begonnen hat.
DEUTSCH Schuhjustierung für 90°-Schnitte (Abb. C) • Stellen Sie einen Gehrungswinkel von 0° ein. • Ziehen Sie den Blattschutz mit Hilfe des Hebels (11) zurück und legen Sie die Säge auf die Sägeblattseite. • Lockern Sie den Gehrungseinstellknopf (6). • Stellen Sie ein Winkelmaß gegen das Sägeblatt und den Schuh, um die 90°-Einstellung zu überprüfen. Sägeblattwechsel (Abb.
DEUTSCH Ausgediente Werkzeuge Spanabsaugung (Abb. A) Ihr Werkzeug ist mit einem Spanauswurf (5) versehen. • Verwenden Sie nur eine Spanabsaugung, die den gültigen Richtlinien für das Sägen von Holz entspricht. Der Absaugschlauch der meisten handelsüblichen Staubsauger kann direkt an den Spanauswurf angeschlossen werden. Verwenden Sie beim Sägen von Leichtmetall keinen Staubsauger ohne entsprechende Funkenschutzstrecke.
DEUTSCH GARANTIE • 30 TAGE GELD ZURÜCK GARANTIE • Wenn Sie mit der Leistung Ihres DEWALTElektrowerkzeuges nicht völlig zufrieden sind, können Sie es unter Vorlage des OriginalKaufbeleges ohne weiteres innerhalb von 30 Tagen bei Ihrem DEWALT-Händler im OriginalLieferumfang zurückgeben und erhalten Ihr Geld zurück. Die Geld zurück Garantie gilt nicht auf Zubehör.
ENGLISH CORDLESS CIRCULAR SAW DW007K/DW007KH Congratulations! EC-Declaration of conformity You have chosen a DEWALT Power Tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional Power Tool users. Technical data Voltage Max. power output No load speed Blade diameter Depth of cut Blade bore Bevel angle adjustment Weight (without battery pack) V W min-1 mm mm mm kg DW007 24 480 4,000 165 55 10 0 - 45° 2.
ENGLISH Safety instructions When using Power Tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents. 2 Consider work area environment Do not expose Power Tools to humidity. Keep work area well lit.
ENGLISH Additional safety instructions for battery packs and chargers Fire hazard! Avoid metal short circuiting the contacts of a detached battery pack. Do not store or carry the battery pack without the battery cap placed over the contacts. • The battery fluid, a 25-30% solution of potassium hydroxide, can be harmful. In case of skin contact, flush immediately with water. Neutralize with a mild acid such as lemon juice or vinegar.
ENGLISH • Saw blades made of high alloy, high speed steel (HSS steel) should not be used. • Only sharp saw blades in perfect working condition should be used; cracked or bent saw blades should be discarded and replaced at once. • Ensure that the saw blade is securely fixed and rotates in the correct direction. Special applications • When cutting narrow workpieces (width less than 80 mm) longitudinally, use a rip fence guide along the longitudinal edge.
ENGLISH • The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug (see below). Brown is for Live (L) (2) and Blue is for Neutral (N) (4). • Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws. Never use a light socket.
ENGLISH • To remove the battery pack, press the release button (14). We recommend to insert the battery pack into the charger directly after removing it from the tool. Battery cap (fig. B) A protective cap is supplied to cover the contacts of a detached battery pack. Without the protective cap in place, loose metal objects could short circuit the contacts, causing a fire hazard and damaging the battery pack. • Take off the protective cap (18) before placing the battery pack (15) in the charger or tool.
ENGLISH • Apply only a gentle pressure to the tool and do not exert side pressure on the saw blade. • Avoid overloading. Prior to operation: • Make sure your battery pack is (fully) charged. • Make sure the guards have been mounted correctly. The saw blade guard must be in closed position. • Make sure the saw blade rotates in the direction of the arrow on the blade. • Do not use excessively worn saw blades. Switching on and off (fig.
ENGLISH GUARANTEE Unwanted tools Take your tool to an authorised DEWALT repair agent where it will be disposed of in an environmentally safe way. • 30 DAY NO RISK SATISFACTION GUARANTEE • If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete as purchased, to the point of purchase, for a full refund or exchange. Proof of purchase must be produced.
ESPAÑOL SIERRA CIRCULAR SIN CABLE DW007K/DW007KH ¡Enhorabuena! Declaración CE de conformidad Usted ha optado por una herramienta eléctrica DEWALT. Muchos años de experiencia y una gran asiduidad en el desarrollo y la innovación de sus productos han convertido DEWALT en un socio muy fiable para el usuario profesional.
ESPAÑOL Instrucciones de seguridad Al utilizar herramientas eléctricas, observe las reglas de seguridad en vigor en su país, a fin de reducir el riesgo de descarga eléctrica, de lesiones y de incendio. Lea las instrucciones de seguridad siguientes antes de utilizar este producto. ¡Conserve bien estas instrucciones de seguridad! Generalidades 1 Mantenga limpia el área de trabajo Un área o un banco de trabajo en desorden aumentan el riesgo de accidentes.
ESPAÑOL Haga reparar o sustituir los dispositivos de seguridad u otros componentes defectuosos según las instrucciones. No utilice la herramienta cuando el interruptor esté defectuoso. Haga sustituir el interruptor en un Centro de Servicio DEWALT. 16 Extraiga la batería Extraiga la batería cuando no la esté utilizando, antes de las operaciones de mantenimiento y cuando cambie algún accesorio.
ESPAÑOL • No coloque nunca la sierra circular sobre una mesa o un banco de trabajo a menos que esté desconectada. Dispositivos de protección operativa • Esta sierra circular debe ser utilizada exclusivamente para cortar madera y plástico. • Compruebe que todos los dispositivos que protegen la hoja de la sierra funcionan correctamente. • No presione nunca los protectores de la hoja. • Libere inmediatamente un protector de la hoja que haya sido presionado; no utilice la sierra si el protector está presionado.
ESPAÑOL 14 Pulsador de arranque para batería 15 Batería Cargador Su cargador DE0246 admite baterías DEWALT 24 V NiCd y NiMH. 15 Batería 16 Cargador 17 Indicador de carga (rojo) Batería (fig. A & B) Carga de la batería (fig. A) Compruebe siempre la corriente eléctrica antes de cargar la batería. Si ésta está en funcionamiento, pero la batería no se carga, lleve el cargador a un concesionario autorizado de reparaciones DEWALT.
ESPAÑOL • Si se deja la batería en el cargador después de la carga inicial de 1 hora, el cargador iniciará automáticamente el modo de puesta a punto. Este modo continuará hasta 8 horas, pero la batería puede retirarse en cualquier momento durante el modo de puesta a punto. Inserción y extracción de la batería • Inserte la batería en la ranura correspondiente de la herramienta hasta que encaje en su lugar. Deberá presionarla con fuerza para que ajuste en el mecanismo de resorte.
ESPAÑOL • Mientras gira el husillo, mantenga pulsado el botón de inmovilización del disco (4) hasta que el disco deje de girar. • Apriete firmemente el tornillo de fijación del disco de sierra utilizando la llave Allen. Ajuste del abridor (fig. D) Para realizar un ajuste correcto del abridor (8), consulte el recuadro de la figura C. Ajuste la distancia del abridor cuando cambie la hoja de la sierra o siempre que sea necesario. • Afloje el tornillo (23) y saque el abridor al máximo.
ESPAÑOL GARANTÍA Lubricación Su herramienta eléctrica no requiere lubricación adicional. Limpieza • Evite que se obturen las ranuras de ventilación y limpie el exterior con regularidad utilizando un paño suave. • Desconecte el cargador antes de limpiar el cárter con un paño. • Quite la batería antes de limpiar su herramienta. Medio ambiente • 30 DÍAS DE SATISFACCIÓN COMPLETA • Si no queda totalmente satisfecho con su herramienta DEWALT, contacte con su Centro de Servicio DEWALT.
FRANÇAIS SCIE CIRCULAIRE SANS FIL DW007K/DW007KH Déclaration CE de conformité Félicitations! Vous avez choisi un outil électrique DEWALT. Depuis de nombreuses années, DEWALT produit des outils électriques adaptés aux exigences des utilisateurs professionnels.
FRANÇAIS Instructions de sécurité Afin de réduire le risque de décharge électrique, de blessure et d’incendie lors de l’utilisation d’outils électriques, observer les consignes de sécurité fondamentales en vigueur. Lire et observer les instructions avant d’utiliser l’outil. Conserver ces instructions de sécurité! Généralités 1 Tenir votre aire de travail propre et bien rangée Le désordre augmente les risques d’accident.
FRANÇAIS 17 Faire réparer votre outil par un Service agréé DEWALT Cet outil est conforme aux consignes de sécurité en vigueur. La réparation des outils électriques est strictement réservée aux personnes qualifiées. Directives de sécurité additionnelles pour batteries et chargeurs Danger d’incendie ! Éviter de courtcircuiter les contacts d’un pack de batterie non fixé avec du métal. Ne rangez pas et ne transportez pas le pack de batterie si le couvercle de protection n’est pas en place sur les contacts.
FRANÇAIS • Au cas où le protecteur de lame serait bloqué, le dégager immédiatement. Ne pas utiliser la scie tant que le protecteur de lame est bloqué. • Ne pas enlever le couteau diviseur. • Le couteau diviseur doit être installé correctement. La distance entre les dents de la lame et le couteau diviseur ne doit pas dépasser 5 mm. Changement de la lame de scie • Utiliser uniquement des lames de scie dont les caractéristiques sont conformes à ces instructions.
FRANÇAIS Ce chargeur à double isolation est conforme à la norme EN 50144; un branchement à la terre n’est donc pas nécessaire. CH CH Toujours utiliser la fiche prescrite lors du remplacement du câble d’alimentation. Type 11 pour la classe II (Isolation double) - outils Type 12 pour la classe I (Conducteur de terre) - outils En cas d’utilisation à l’extérieur, connecter les outils portatifs à un disjoncteur FI.
FRANÇAIS Insertion et retrait du pack-batteries • Insérez le pack-batteries dans l’emplacement correspondant de l’outil jusqu’à ce qu’il se mette en place en émettant un déclic. Il vous faudra employer un peu de force pour enclencher complètement le mécanisme à ressort. • Pour retirer le pack-batteries, appuyez sur le bouton de dégagement (14). Il est recommandé d’insérer directement le pack batterie dans le chargeur après l’avoir retiré de l’outil. Couvercle des batteries (fig.
FRANÇAIS Réglage du couteau diviseur (fig. D) Pour un réglage correct du couteau diviseur (8), se reporter à l’encart dans la figure C. Régler le jeu du couteau diviseur après remplacement de la lame ou en cas de déréglage. • Desserrer la vis (23) et tirer le couteau diviseur à sa longueur maximale. • Régler le jeu et serrer la vis. • La coupe étant plus nette du côté où la lame sort de la pièce, il convient de fixer cette dernière le dos dirigé vers la lame de scie.
FRANÇAIS Environnement GARANTIE • 30 JOURS D’ENGAGEMENT SATISFACTION • Packs-batteries rechargeables Les packs-batteries doivent être rechargés dès qu’ils ne fournissent plus suffisamment d’énergie pour des travaux réalisés aisément auparavant. Lorsque le pack-batteries ne se recharge plus correctement, il est à remplacer. Au moment de le jeter, penser à notre environnement: • Décharger votre pack-batteries complètement en utilisant votre outil jusqu’à arrêt complet. Ensuite, enlever le pack-batteries.
ITALIANO SEGA CIRCOLARE A BATTERIA DW007K/DW007KH Dichiarazione CE di conformità Congratulazioni! Siete entrati in possesso di un Elettroutensile DEWALT. Anni di esperienza, continui miglioramenti ed innovazioni tecnologiche fanno dei prodotti DEWALT uno degli strumenti più affidabili per l’utilizzatore professionale.
ITALIANO Norme generali di sicurezza Durante l’utilizzo di utensili elettrici adottate sempre le elementari norme di sicurezza atte a ridurre i rischi d’incendio, scariche elettriche e ferimenti. Leggere attentamente le seguenti istruzioni prima di utilizzare il prodotto. Custodire con cura le istruzioni! Norme generali 1 Tenere pulita l’area di lavoro Ambienti e banchi di lavoro in disordine possono essere causa d’incidenti.
ITALIANO 16 Rimuovere il gruppo batterie Rimuovere il gruppo batterie quando l’elettroutensile rimane inutilizzato, prima di effettuare gli interventi e durante la sostituzione degli accessori. 17 Rivolgersi ai Centri di Assistenza Tecnica autorizzati DEWALT per le riparazioni Il presente Elettroutensile è conforme alle principali norme di sicurezza vigenti. Per evitare pericolo di infortuni, le riparazioni alle apparecchiature elettriche devono essere effettuate esclusivamente da personale qualificato.
ITALIANO Dispositivi di sicurezza operativi • La sega circolare deve essere utilizzata esclusivamente per il taglio di legno o plastica. • Assicurarsi che tutti i dispositivi di protezione della lama siano in perfette condizioni di funzionamento. • Evitare assolutamente il bloccaggio dei ripari lama della sega. • Liberare immediatamente la difesa della lama rimasta eventualmente bloccata. • Non rimuovere il coltello apritaglio.
ITALIANO 15 Gruppo batterie 16 Caricabatterie 17 Indicatore di carica (rosso) Norme di sicurezza elettrica Il motore elettrico è stato predisposto per operare con un unico voltaggio. Assicurarsi che il voltaggio a disposizione corrisponda a quello indicato sulla targhetta. Il caricabatterie DEWALT è fornito di doppio isolamento, in ottemperanza alla norma EN 50144, per le quali non è richiesta la messa a terra.
ITALIANO • Per mettere a punto il gruppo batteria, collocare la batteria nel caricabatteria, come di consueto. La luce rossa lampeggerà ininterrottamente indicando che il ciclo di carica è cominciato. • Quando il ciclo di carica di 1 ora è completo, la luce rimane accesa ininterrottamente senza lampeggiare. Il gruppo è completamente carico e può adesso essere usato.
ITALIANO • Allentare la manopola di regolazione dell’inclinazione (6). • Posizionare una squadra contro la lama e la piastra d’appoggio per controlare l’angolo a 90°. Sostituzione della lama (fig. D) • Innestare il pulsante di bloccaggio della lama (4) e svitare la vite di fissaggio della lama (9) ruotandola in senso orario con la chiave per brugole fornita insieme all’utensile. • Portare indietro la protezione inferiore della lama con l’azionamento (11) e sostituire la lama (21).
ITALIANO Durante le operazioni di segatura dei metalli, non utilizzare l’aspiratore in assenza di un’adeguata protezione parascintille. Consultate il vostro rivenditore per ottenere ulteriori informazioni sugli accessori disponibili. Manutenzione Il Vostro Elettroutensile DEWALT è stato studiato per durare a lungo richiedendo solo la minima manutenzione. Per prestazioni sempre soddisfacenti occorre avere cura dell’utensile e sottoporlo a manutenzione periodica.
ITALIANO GARANZIA • GARANZIA DI 30 GIORNI DI TOTALE SODDISFAZIONE • Se non siete completamente soddisfatti delle prestazioni del vostro utensile DEWALT, potrete restituirlo entro 30 giorni dalla data di acquisto, presso una nostra filiale di assistenza per ottenere il rimborso o il cambio dell’utensile, presentando debita prova dell’avvenuto acquisto.
NEDERLANDS SNOERLOZE CIRKELZAAG DW007K/DW007KH Gefeliciteerd! EG-Verklaring van overeenstemming U heeft gekozen voor een elektrische machine van DEWALT. Jarenlange ervaring, voortdurende produktontwikkeling en innovatie maken DEWALT tot een betrouwbare partner voor de professionele gebruiker. Technische gegevens Spanning Nuttig vermogen (max.) Toerental, onbelast Zaagbladdiameter Maximum zaagdiepte Asgat Instelling afschuinhoek Gewicht (zonder accu) V W min-1 mm mm mm kg DW007 24 480 4.
NEDERLANDS Veiligheidsinstructies Neem bij het gebruik van elektrische machines altijd de plaatselijk geldende veiligheidsvoorschriften in acht in verband met brandgevaar, gevaar voor elektrische schokken en lichamelijk letsel. Lees ook onderstaande instructies aandachtig door voordat u met de machine gaat werken. Bewaar deze instructies zorgvuldig! Algemeen 1 Zorg voor een opgeruimde werkomgeving Een rommelige werkomgeving leidt tot ongelukken.
NEDERLANDS 16 Verwijder de accu Verwijder de accu wanneer u de machine niet gebruikt, alvorens onderhoud te verrichten of hulpstukken te verwisselen. 17 Wendt u voor reparaties tot een erkend DEWALT Service-center Deze elektrische machine voldoet aan alle geldende veiligheidsvoorschriften. Ter voorkoming van ongevallen mogen reparaties uitsluitend door daartoe bevoegde technici worden uitgevoerd.
NEDERLANDS Beveiligingen • De cirkelzaag mag uitsluitend gebruikt worden voor het zagen van hout en plastic. • Controleer of alle beschermkappen perfect functioneren. • Nooit de beschermkappen blokkeren. • Gebruik de zaag niet wanneer de beschermkap geblokkeerd is. • Verwijder nooit het spouwmes.
NEDERLANDS Controleer tevens of de ingangsspanning van de oplader overeenkomt met uw netspanning. Uw DEWALT-oplader is dubbel geïsoleerd overeenkomstig EN 50144. Vervangen van het snoer of de stekker Als de stekker of het snoer wordt vervangen, moet de oude stekker c.q. het oude snoer worden weggegooid. Het is gevaarlijk om de stekker van een los snoer in het stopcontact te steken. Gebruik van verlengsnoeren Gebruik verlengsnoeren alleen in uiterste noodzaak.
NEDERLANDS Wij bevelen aan om de accu direct in de oplader te plaatsen nadat hij uit de machine is verwijderd. Accu-afdekdop (fig. B) De meegeleverde afdekdop wordt gebruikt om de contactpunten van de losse accu te beschermen. Zonder de afdekdop kunnen de contactpunten worden kortgesloten door rondslingerende metalen voorwerpen, waardoor brandgevaar ontstaat en de accu beschadigd raakt. • Neem de afdekdop (12) af voordat u de accu (9) in de lader of de machine plaatst.
NEDERLANDS Aanwijzingen voor gebruik • Neem altijd de veiligheidsinstructies in acht en houdt u aan de geldende voorschriften. • Zet het werkstuk stevig vast. • Oefen geen overmatige druk uit op de machine. Geef geen zijdelingse druk op het zaagblad. • Voorkom overbelasting. Alvorens met de machine te gaan werken: • Zorg dat de accu (helemaal) is opgeladen. • Controleer of alle beschermkappen juist gemonteerd zijn. De beschermkap van het zaagblad moet gesloten zijn.
NEDERLANDS Het milieu GARANTIE • 30 DAGEN «NIET GOED, GELD TERUG» GARANTIE • Oplaadbare accu De duurzame accu moet worden opgeladen, zodra deze niet meer genoeg energie levert voor werkzaamheden die daarvóór nog moeiteloos konden worden verricht. Versleten accu’s dienen op milieubewuste wijze te worden verwijderd: • Gebruik de energie van de accu helemaal op en verwijder dan de accu uit de boormachine. • NiCd- en NiMH-accu’s zijn recycleerbaar.
NORSK OPPLADBAR SIRKELSAG DW007K/DW007KH Gratulerer! CE-Sikkerhetserklæring Du har valgt et DEWALT elektroverktøy. Årelang erfaring, konstant produktutvikling og fornyelse gjør DEWALT til en av de mest pålitelige partnere for profesjonelle brukere. Tekniske data Spenning Utgangseffekt (max) Turtall, ubelastet/min Bladdiameter Snittdybde Bladhulldiameter Skråsnitt Vekt V W mm mm mm kg DW007 24 480 4.
NORSK Sikkerhetsforskrifter Ta deg tid til å lese nøye gjennom bruksanvisningen før du begynner å bruke maskinen. Oppbevar bruksanvisningen på et lett tilgjengelig sted slik at alle som skal bruke maskinen, lett kan finne denne. I tillegg til forskriftene under må alle vernebestemmelsene til Statens Arbeidstilsyn følges når det gjelder arbeid med elektroverktøy.
NORSK Unngå risiko: Overlat alltid reparasjon av elektriske apparater til kvalifisert servicepersonale. Les bruksanvisningen før laderen tas i bruk Ekstra sikkerhetsregler for batteripakker og ladere Må ikke utsettes for fukt Brannfare! Pass på at metall ikke kortslutter kontaktene på en frakoplet batteripakke. Ikke oppbevar eller bær batteripakken uten at beskyttelseshetten er satt over kontaktene. • Batterivæsken, en 25-30 % løsning av kaliumhydroksid, kan være skadelig.
NORSK Kontroll og bytte av sagbladet • Bruk bare sagblad som samsvarer med spesifikasjonene i denne bruksanvisningen. • Bruk bare skarpe sagblad i perfekt stand; sprukne eller bøyde blad må avhendes og erstattes øyeblikkelig. • Pass på at sagbladet er sikkert fastspent og roterer i riktig retning. Spesielle anvendelser • Når du sager smale arbeidsemner (bredden er mindre enn 80 mm) på langs, bruker du en føringslinjal i lengderetningen.
NORSK • Slå alltid av verktøyet før du setter inn eller tar ut batteripakken. • Før du bruker verktøyet må du sjekke at batteripakken er satt riktig på plass. Bare bruk DEWALT batterier og lader. Batteripakke (fig. A & B) Lading av batteripakken (fig. A) Kontroller alltid nettet før du lader batteripakken. Hvis det er strøm på nettet, men batteripakken ikke blir oppladet, må du bringe laderen til et DEWALTautorisert serviceverksted. Under oppladningen kan batteripakken kjennes varm ved berøring.
NORSK Bruk vernebriller når du setter i støpslet. Varmt/kaldt batteri ventetid Når laderen oppdager et batteri som er varmt/kaldt, starter den automatisk en varmt/kaldt batteri ventetid, som utsetter ladningen til batteriet har en skikket temperatur. Laderen kopler da automatisk tilbake til normal ladning av batteriet. Denne egenskapen garanterer maksimal levetid for batteriet. Den røde indikatoren blinker lenge, og deretter kort mens den er i ventetid modus. Justerering av snittdybden (fig.
NORSK Ved skråsnitt 45°, snittindikatoren står i flukt med den venstre (ytre) siden av sagbladet. Ved skråsnitt 0°, snittindikatoren står i flukt med den høyre (indre) siden av sagbladet. Sponutkast (fig. A) Verktøyet er utstyrt med et sponuttak (5). • Bruk alltid en støvsuger som er utformet i samsvar med anvendbare direktiver om sponutslipp når det sages i tre. Vakuumslanger til de fleste støvsugere passer rett inn i avsugsmunnstykket. Bruk ikke støvsuger ved saging av metall uten å ha gnistbeskyttelse.
NORSK GARANTI • 30 DAGERS FORNØYD-KUNDEGARANTI • Hvis du ikke er tilfreds med ditt DEWALT verktøy, kan det returneres innen 30 dager til din DEWALT forhandler eller til et DEWALT autorisert serviceverksted og du kan bytte eller få pengene tilbake. Kvittering må fremlegges. • 1 ÅRS FRI VEDLIKEHOLDSERVICE • Skulle ditt DEWALT verktøy trenge vedlikehold eller service i de første 12 månedene etter det ble kjøpt, vil dette bli utført gratis av et autorisert DEWALT serviceverksted.
PORTUGUÊS SERRA CIRCULAR A BATERIAS DW007K/DW007KH Parabéns! Declaração CE de conformidade Escolheu uma Ferramenta Eléctrica DEWALT. Muitos anos de experiência, um desenvolvimento contínuo de produtos e o espírito de inovação fizeram da DEWALT um dos parceiros mais fiáveis para os utilizadores profissionais. Dados técnicos DW007 24 480 4.000 165 55 10 0 - 45° kg 2,9 Voltagem Potência de saída (max) Velocidade em vazio Diâmetro da folha Profund. do corte Orifício da folha Ajuste do âng.
PORTUGUÊS Instruções de segurança Quando usar Ferramentas Eléctricas, cumpra sempre os regulamentos de segurança aplicáveis no seu país para reduzir o risco de incêndio, de choque eléctrico e de ferimentos. Leia as seguintes instruções de segurança antes de tentar utilizar este produto. Guarde estas instruções! Instruções gerais 1 Mantenha a área de trabalho arrumada As mesas e áreas de trabalho desarrumadas podem provocar ferimentos.
PORTUGUÊS Não utilize a ferramenta se o interruptor não estiver a funcionar. Mande substituir o interruptor num Centro de Assistência Técnica DEWALT. 16 Retire o jogo de baterias Retire o jogo de baterias quando não estiverem em uso, antes de manutenção e ao substituir accessórios. 17 Mande consertar a sua ferramenta por um Centro de Assistência Técnica DEWALT Esta Ferramenta Eléctrica está conforme às regulamentações de segurança que lhe dizem respeito.
PORTUGUÊS Dispositivos de protecção em operação • A serra circular só pode ser utilizado para cortar madeira ou plástico. • Certifique-se de que todos os dispositivos foram examinados para que a serra funcione perfeitamente. • Nunca obstrua a guarda da lâmina. • Liberte directamente o resguardo e não use a serra se o resguardo estiver obstruido. • Não se deve retirar a guia de corte. • A guia de corte deve estar montada corectamente; a distância entre o rebordo dentado e a guia de corte deve ser ao max.
PORTUGUÊS 15 Bateria 16 Carregador 17 Indicator da carga (vermelho) Segurança eléctrica O carregador foi concebido para uma única tensão. Verifique sempre se a tensão corresponde à voltagem indicada na placa de identificação. O seu carregador DEWALT tem duplo isolamento em conformidade com o estipulado na norma EN 50144, não sendo, por isso, necessária uma ligação à terra.
PORTUGUÊS Inserir ou retirar o conjunto de baterias • Insira o conjunto de baterias na ranhura correspondente da ferramenta até ouvir um estalido. Poderá ter de forçar um pouco para encaixar devidamente o mecanismo com molas. • Para retirar o conjunto de baterias, prima o manipulo (14). Recomendamos que insira o conjunto da bateria directamente no carregador depois de a remover da ferramenta. Tampa da bateria (fig. B) É fornecida uma tampa de protecção para tapar os contactos de uma bateria solta.
PORTUGUÊS Ajuste da guia de corte (fig. D) Para um ajuste correcto da guia de corte (8), verifique o que está na figura C. Regule limpeza da faca de corte quando a folha da serra fôr substituida ou quando necessário. • Desenrosque o parafuso (23) e retire a faca de corte no seu comprimento máximo. • Regule a limpeza e aperte o parafuso. Modo de emprego • Cumpra sempre as instruções de segurança e os regulamentos aplicáveis. • Certifique-se de que o material a serrar está bem fixo no devido lugar.
PORTUGUÊS GARANTIA Lubrificação A sua Ferramenta Eléctrica não precisa de lubrificação suplementar. Limpeza • Retire a ficha do carregador da tomada antes de limpar o corpo do carregador utilizando um pano macio. • Remova a bateria antes de limpar a sua Ferramenta Eléctrica. • Conserve livres as aberturas de ventilação e limpe regularmente o corpo da máquina utilizando um pano macio.
SUOMI AKKUKÄSIPYÖRÖSAHA DW007K/DW007KH Onneksi olkoon! CE-Vaatimustenmukaisuustodistus Olet valinnut DEWALT-sähkötyökalun. Monivuotisen kokemuksen, ahkeran tuotekehittelyn ja uudistusten ansiosta DEWALT on yksi ammattikäyttäjien luotettavimmista yhteistyökumppaneista.
SUOMI Turvallisuusohjeet Lue käyttöohje huolellisesti ennen koneen käyttöönottoa. Säilytä käyttöohje kaikkien koneen käyttäjien ulottuvilla. Näiden ohjeiden lisäksi tulee aina seurata työsuojeluviranomaisten ohjeita. VAROITUS! Sähköiskujen, loukkaantumisten ja palovaaran ehkäisemiseksi on noudatettava seuraavia perusturvallisuustoimenpiteitä. 1 Käytä kuulosuojaimia Eri materiaaleja työstettäessä saattaa melutaso vaihdella ja kohoaa toisinaan yli 85 dB(A) rajan. Suojaa itsesi ja käytä aina kuulosuojaimia.
SUOMI Akkujen ja latauslaitteiden turvaohjeet Palovaara! Vältä irrotetun akuston metallikontaktien asettamista oikosulkuun metallilla. Älä säilytä tai kanna akustoa ilman, että mukana tuleva suojakorkki on asetettu kontaktien päälle. • Akkuneste, 25 - 30 % hydroksidiliuos, saattaa olla haitallista. Jos akkunestettä pääsee iholle, huuhdo se runsaalla vedellä. Neutraloi akkuneste etikalla tai sitruunamehulla.
SUOMI Erityissovellukset • Kun sahaat kapeita työkappaleita (leveys alle 80 mm) pitkittäissuuntaan, käytä apuna leikkuuohjainta ja työntökappaletta. • Kun sahaat pyöreitä puuosia, pidä työstökappaletta tukevasti sahanterän molemmin puolin, ettei työstökappale lipsu. • Varmista etteivät sahatut puunkappaleet tartu sahanterän hampaisiin ja sinkoa ilmaan. Suojaus takaisiniskulta • Kun sahanterä takertuu työstökappaleeseen, saha saattaa sinkoutua kohti käyttäjää.
SUOMI Älä lataa akkuja, mikäli ympäristön lämpötila on alle 4 °C tai yli 40 °C. Suositeltava latauslämpötila on noin 24 °C. • Laita akkupaketti (9) latausta varten latauslaitteeseen (10) kuten kuvassa on esitetty ja kytke latauslaite sähköverkkoon. Varmista, että akku on tukevasti paikallaan latauslaitteessa. Punainen latausvalo (11) vilkkuu. Noin yhden tunnin varausajan jälkeen se lakkaa vilkkumasta ja alkaa palaa yhtäjaksoisesti. Tällöin akkupaketti on täysin latautunut.
SUOMI Vinosahauskulman säätö (kuvat A & C) Vinosahauskulma voidaan säätää välille 0° - 45°. • Löysää vinosahauksen säätönuppi (6). • Säädä vinosahauskulma kallistamalla pohjalevyä (12). • Kiristä vinosahauksen säätönuppi (6). Pohjalevyn säätö 90°:n sahauksia varten (kuva C) • Säädä sahaan 0°:n vinosahauskulma. • Vedä sahanterän suojusta taaksepäin vivusta (11) ja aseta saha kyljelleen sahanterä vaaka-asennossa. • Löysää vinosahauksen säätönuppi (6). • Aseta suorakulma sahanterää ja pohjalevyä vasten.
SUOMI Huolto-ohjeita Ympäristö DEWALT sähkötyökalusi on suunniteltu käytettäväksi pitkän aikaa mahdollisimman vähällä huollolla. Asianmukainen käyttö ja säännönmukainen puhdistus takaavat laitteen jatkuvan toiminnan. Voitelu Sähkötyökalusi ei tarvitse lisävoitelua. Puhdistus • Vedä laturin pistotulppa pistorasiasta, ennenkuin puhdistat vaipan pehmeällä rievulla. • Irrota akkukotelo, ennenkuin puhdistat sähkötyökalusi. • Pidä tuuletusaukot puhtaina ja puhdista runko säännöllisesti pehmeällä rievulla.
SUOMI TAKUU • 30 PÄIVÄN TYYTYVÄISYYSTAKUU • Jos et ole täysin tyytyväinen DEWALT-työkaluusi, palauta se myyjälle tai valtuutettuun DEWALThuoltopisteeseen 30 päivän sisällä ostopäivästä, niin saat rahasi takaisin tai vaihtokoneen. Tuote on palautettava täydellisenä ja ostokuitti on esitettävä. • YHDEN VUODEN ILMAINEN YLLÄPITOHUOLTO • DEWALT-työkalusi kunnossapito ja huolto suoritetaan ilmaiseksi 12 kuukauden sisällä ostopäivästä huoltopisteessämme.
SVENSKA UPPLADDNINGSBAR CIRKELSÅG DW007K/DW007KH Vi gratulerar! CE-Försäkran om överensstämmelse Du har valt ett DEWALT elverktyg. Mångårig erfarenhet, ihärdig produktutveckling och förnyelse gör DEWALT till ett av de mest pålitliga namnen för professionella användare.
SVENSKA Säkerhetsinstruktioner Innan Du börjar använda maskinen, tag några minuter i anspråk för att läsa igenom bruksanvisningen. Spara bruksanvisningen lättillgängligt, så att alla som använder maskinen har tillgång till bruksanvisningen. Förutom nedanstående instruktioner, följ alltid Arbetarskyddsstyrelsens regler. VARNING! När man använder elverktyg skall dessa grundläggande säkerhetsinstruktioner alltid följas för att minska risken för elektriska stötar, personskada och brand.
SVENSKA För att undvika olycksfall ska reparationer och elanordningar endast utföras av behörig elektromontör. Läs bruksanvisningen Tillkommande säkerhetsanvisningar för batterier och laddare Får ej utsättas för väta Brandfara! Undvik att metallstycken skulle kunna kortsluta kontakterna på ett uttaget batteripaket. Varken bär eller förvara batteripaketet utan att den medföljande skyddshättan sitter över kontakterna. • Batterivätskan, en 25-30% lösning av kaliumhydroxid, kan vara skadlig.
SVENSKA • Använd endast skarpa sågklingor i perfekt skick; spruckna eller böjda blad måste genast kastas och ersättas. • Se till att sågklingan är ordentligt fastsatt och roterar i rätt riktning. Speciella tillämpningar • När du klyver smala arbetsstycken (smalare än 80 mm) måste parallelanslaget användas. • Använd vid sågning med arbetsstycket inklämt en anordning som hindrar det från att slå tillbaka.
SVENSKA Använd endast DEWALT batterier och laddare. Batteripaket (fig. A & B) Laddning av batteripaketet (fig. A) Kontrollera alltid nätanslutningen innan batteripaketet laddas. Om nätanslutningen fungerar men batteripaketet inte laddas, tag laddaren till en godkänd DEWALT serviceverkstad. Under laddningen kan laddaren och batteripaketet kännas varma. Detta är normalt och betyder inte att något problem föreligger. Ladda inte batteripaketet vid omgivningstemperaturer på < 4 °C eller > 40 °C.
SVENSKA Fördröjning hett/kallt batteri När laddaren registrerar att batteriet är hett eller kallt, kopplas automatiskt en fördröjning in så att laddningen inte sker förrän batteriet har en lämplig temperatur. Laddaren kopplar sedan automatiskt om till normal laddning. Denna funktion garanterar en maximal livslängd för batteriet. Den röda indikatorn blinkar långt och sedan kort när laddaren befinner sig i fördröjningsläge. Djupinställning (fig. A) • Lossa djupinställningen (13).
SVENSKA Vid fasvinkel 0°, indikatorn ligger på linje med sågklingans högra (inre) sida. Dammutsugning (fig. A) Din cirkelsåg är försedd med en dammutsugningsöppning (5). • Använd alltid en dammsugare som fyller gällande föreskrifter gällande dammutsläpp vid sågning av trä. Slangen hos de flesta vanliga dammsugare passar direkt i utsugningsmunstycket. Använd inte dammsugare utan att ha ett riktigt gnistskydd vid sågning av metall. Kontakta Din återförsäljare för vidare information om lämpliga tillbehör.
SVENSKA GARANTI • 30 DAGARS NÖJD-KUND-GARANTI • Om du inte är fullständigt nöjd med din DEWALTprodukts prestanda behöver du endast returnera den inom 30 dagar, komplett som vid köpet, till ditt inköpsställe eller en DEWALT auktoriserad serviceverkstad för fullständig återbetalning eller utbyte. Inköpsdatum måste påvisas. • ETT ÅRS FRI FÖREBYGGANDE SERVICE • Om din DEWALT-produkt inom 12 månader efter inköpsdatum kräver underhåll eller service, utförs detta kostnadsfritt av en auktoriserad serviceverkstad.
TÜRKÇE KABLOSUZ DAİRE TESTERESİ DW007K/DW007KH Tebrikler! Bir D E WALT elektrikli aletini seçmiş bulunuyorsunuz. Ürün geliştirme ve yenilemede y llar n deneyimi D E WALT’ profesyonel kullan c lar işin en güvenilir partnerlerden biri haline getirmektedir.
TÜRKÇE Güvenlik talimatlar* Elektrikli aletleri kullan rken daima, yangin, elektrik çarpmas ve yaralanma riskini azaltmak için, ülkenizde uygulanabilecek güvenlik kurallar na uyun. Bu ürünü kullanma girişiminde bulunmadan önce, aşağ daki güvenlik talimatlar n dikkatle okuyun. Bu talimatlar güvenli bir yerde saklay n. 10 11 12 Genel Bilgiler 1 Çal*şma alan*n*z* temiz tutun Dağ n k yerler ve tezgahlar kazaya neden olabilir.
TÜRKÇE 17 Aletinizi, yetkili bir D E WALT onar*m merkezinde onart*n Bu elektrikli alet ilgili güvenlik kurallar na uygundur. Tehlikeyi önlemek için, elektrikli aletler, sadece kalifiye teknisyenler taraf ndan onar lmal d r. Aküler ve şarjlar için ek güvenlik talimatlar Yang n tehlikesi! Yerinden ç kar lm ş bataryan n uçlar n n k sa devre yapmas n önleyin! Bataryalar uçlar nda size verilen koruyucu kapaklar olmadan saklamay n veya taş may n.
TÜRKÇE • Testereyi kapatmadan önce kesinlikle bir masaya ya da çal şma tezgah na koymay n. • İç kesmeler d ş nda daima keski demiri kullan n. Çal*şma için koruyucu donan*mlar • Daire testereyi yalnìzca ahşap ya da plastik kesmek için kullan n. • Testere b çağ n örten tüm parçalar n iyi durumda olup olmad ğ n kontrol edin. • Asla testere koruyucular n s k şt rmay n. • S k şm ş testere b çağ n derhal aç n ve koruyucu s k şm ş durumdayken testereyi kullanmay n. • Keski demirini yerinden ç kartmay n.
TÜRKÇE 5 Toz ağz 6 Meyil ayar düğmesi 7 Kesik göstergesi 8 Keski demiri 9 B çak s k şt rma vidas 10 Alt siper 11 Alt siper geri çekme manivelas 12 Taban 13 Derinlik ayar düğmesi 14 Akü salma düğmesi 15 Akü Şarj adaptör DE0246 şarj cihaz n zla D E WALT 24 V NiCd ve NiMH batarya kutular na uyumludur. 15 Akü 16 Şarj adaptör 17 Şarj lamba (k rm z ) Sadece D E WALT aküleri ve şarj adaptör ile kullan n.
TÜRKÇE • Akü tak m n z ayarlamak için, aküyü şarja her zaman olduğu gibi yerleştirin. Şarj döngüsünün başlad ğ n belirtmek üzere k rm z ş k sürekli yan p sönecektir. • 1 saatlik şarj döngüsü tamamland ğ nda, ş k yan p sönmeyi durduracak ve sürekli yanacakt r. Akü art k tam dolmuştur ve her an kullan ma haz rd r. • Başlang çtaki 1 saatlik şarjdan sonra tak m şarjda b rak l rsa, şarj cihaz otomatik olarak ayar modunu başlat r.
TÜRKÇE • Manivelay (11) kullanarak b çak siperini çekin ve b çağ (21) yerleştirin. Rondeleri (20 & 22) tekrar doğru konumlar na yerleştirin. • B çağ n dönüş yönünü kontrol edin. • Rondeleleri tespit etmek için b çak s k şt rma vidas n (9) elle çevirin (saatin aksi yönünde). • Mili, b çak durana kadar çevirirken b çak tespit düğmesine (4) bas n. • Allen anahtar yla b çak s k şt rma vidas n s k n. Keski demirinin ayarlanmas (şekil D) Doğru keski demiri (8) ayar için bknz. şekil C.
TÜRKÇE GARANTİ Yağlama Elektrikli aletiniz, ek yağlama gerektirmez. Temizlik • Temizlemeden önce, şarj adaptörünü AC prizinden ç kart n. • Elektrikli aletinizi temizlemeden önce aküyü sökün. • Havaland rma kanallar n n temiz ve aç k olmas na dikkat edin ve aletin gövdesini düzenli olarak yumuşak bir bezle temizleyin.
∂§§∏¡π∫∞ E¶∞¡∞º√ƒ∆π∑√ªE¡√ ¢π™∫√¶ƒπ√¡√ DW007K/DW007KH £ÂÚÌ¿ Û˘Á¯·ÚËÙ‹ÚÈ·! ¢È·Ï¤Í·Ù ¤Ó· ·fi Ù· Ì˯·Ó‹Ì·Ù· Ù˘ DEWALT. ∏ Ôχ¯ÚÔÓË ÂÌÂÈÚ›· Ù˘ DEWALT, Ë Û˘Ó¯‹˜ ÂͤÏÈÍË ÙˆÓ ÚÔ˚fiÓÙˆÓ Ù˘ Î·È Ë ÂÊ·ÚÌÔÁ‹ ηÈÓÔÙÔÌÈÒÓ ÙËÓ Î·ıÈÛÙÔ‡Ó ¤Ó·Ó ·fi ÙÔ˘˜ Èfi ·ÍÈfiÈÛÙÔ˘˜ Û˘ÓÂÚÁ¿Ù˜ ÙˆÓ Â·ÁÁÂÏÌ·ÙÈÒÓ. ∆¯ÓÈο ¯·Ú·ÎÙËÚÈÛÙÈο ∆¿ÛË V ∞ÔÚÚÔÊÔ‡ÌÂÓË W ∆·¯‡ÙËÙ· ¿Ó¢ ÊÔÚÙ›Ô˘ min-1 ¢È¿ÌÂÙÚÔ˜ Ï›‰·˜ mm µ¿ıÔ˜ ÎÔ‹˜ mm √‹ Ï›‰·˜ mm ƒ‡ıÌÈÛË ÏÔÍ‹˜ ÁˆÓ›·˜ µ¿ÚÔ˜ (¯ˆÚ›˜ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ) kg DW007 24 480 4.
∂§§∏¡π∫∞ √‰ËÁ›Â˜ ·ÛÊ·Ï›·˜ √Ù·Ó ¯ÚËÛÈÌÔÔț٠ËÏÂÎÙÚÈο ÂÚÁ·Ï›· Ú¤ÂÈ Ó· Ï·Ì‚¿ÓÂÙ ¿ÓÙÔÙ ˘fi„Ë ÙÔ˘˜ ηÓfiÓ˜ ·ÛÊ·Ï›·˜ Ô˘ ÈÛ¯‡Ô˘Ó ÛÙË ¯ÒÚ· Û·˜ ÚÔÎÂÈ̤ÓÔ˘ Ó· ·ÔÊ¢¯ı› Ô Î›Ó‰˘ÓÔ˜ ˘ÚηÁÈ¿˜, ËÏÂÎÙÚÔÏËÍ›·˜ Î·È ÙÚ·˘Ì·ÙÈÛÌÔ‡. ¶ÚÈÓ ¯ÚËÛÈÌÔÔÈ‹ÛÂÙ ÙÔ ÂÚÁ·ÏÂ›Ô ‰È·‚¿ÛÙ ÚÔÛÂÎÙÈο ÙȘ ·Ú·Î¿Ùˆ Ô‰ËÁ›Â˜ Î·È Ê˘Ï¿Í٠٘ ηϿ. 1 ¢È·ÙËÚ›Ù ηı·Úfi ÙÔ ¯ÒÚÔ ÂÚÁ·Û›·˜ ∞ηٿÛÙ·ÙÔÈ ¯ÒÚÔÈ Î·È ¿ÁÎÔÈ ÂÁ΢ÌÔÓÔ‡Ó Î›Ó‰˘ÓÔ ÙÚ·˘Ì·ÙÈÛÌÔ‡.
∂§§∏¡π∫∞ 15 EϤÁ¯ÂÙÂ Â¿Ó ÙÔ ÂÚÁ·ÏÂ›Ô Û·˜ ¤¯ÂÈ ‚Ï¿‚˜ ¶ÚÈÓ ¯ÚËÛÈÌÔÔÈ‹ÛÂÙ ÙÔ ÂÚÁ·Ï›Ô, ÂϤÁÍÙ ÙÔ ÚÔÛÂÎÙÈο ÁÈ· ÂӉ¯fiÌÂÓ˜ ‚Ï¿‚˜ ÁÈ· Ó· ‚‚·Èˆı›Ù fiÙÈ ı· ÏÂÈÙÔ˘ÚÁ‹ÛÂÈ fiˆ˜ Ú¤ÂÈ. EϤÁÍÙÂ Â¿Ó Ù· ÎÈÓËÙ¿ ̤ÚË Â›Ó·È ÛˆÛÙ¿ Û˘Ó‰Â‰Â̤ӷ Î·È Â˘ı˘ÁÚ·ÌÌÈṲ̂ӷ, Â¿Ó ‰ÂÓ ¤¯Ô˘Ó Û¿ÛÂÈ ÎÔÌÌ¿ÙÈ·, Â¿Ó Â›Ó·È ÛˆÛÙ¿ Û˘Ó·ÚÌÔÏÔÁË̤ӷ Î·È Â¿Ó ÏËÚÔ‡ÓÙ·È fiϘ ÔÈ Û˘Óı‹Î˜ ÁÈ· ÙË ÛˆÛÙ‹ ÏÂÈÙÔ˘ÚÁ›· ÙÔ˘ ÂÚÁ·Ï›Ԣ.
∂§§∏¡π∫∞ ºÔÚ¤ÛÙ ÚÔÛٷ٢ÙÈο Á˘·ÏÈ¿ fiÙ·Ó ‚¿ÏÂÙ ÙËÓ Ú›˙· (DE0246) ¶ÚfiÛıÂÙÔÈ Î·ÓfiÓ˜ ·ÛÊ·Ï›·˜ ÁÈ· ‰ÈÛÎÔÚ›ÔÓ· ∫·Ù¿ ÙÔ ÚÈfiÓÈÛÌ· • ∞Ê·ÈÚ¤ÛÙ fiÏ· Ù· ηÚÊÈ¿ Î·È ÌÂÙ·ÏÏÈο ·ÓÙÈΛÌÂÓ· ·fi ÙÔ ˘fi ηÙÂÚÁ·Û›· ·ÓÙÈΛÌÂÓÔ ÚÈÓ ·Ú¯›ÛÂÙ ӷ ÂÚÁ¿˙ÂÛÙÂ. • ªËÓ ÂȯÂÈÚ›Ù ӷ ÚÈÔÓ›ÛÂÙ Ôχ ÌÈÎÚ¿ ·ÓÙÈΛÌÂÓ·. • ∞ÊÔ‡ Û‚‹ÛÂÙ ÙÔ ÂÚÁ·Ï›Ô, ÌË ÚÔÛ·ı‹ÛÂÙ ÔÙ¤ Ó· ÛÙ·Ì·Ù‹ÛÂÙ ÙË Ï›‰· ÙÔ˘ ÚÈÔÓÈÔ‡ Ȥ˙ÔÓÙ¿˜ ÙËÓ ÛÙÔ Ï¢Úfi Ù˘. • ªË ‚¿˙ÂÙ ÔÙ¤ ÙÔ ‰ÈÛÎÔÚ›ÔÓÔ ÛÙÔ ÙÚ·¤˙È ‹ ÛÙÔÓ ¿ÁÎÔ ÂÚÁ·Û›·˜ Â¿Ó ‰ÂÓ ¤¯ÂÈ Û‚‹ÛÂÈ.
∂§§∏¡π∫∞ EÏÂÁ¯Ô˜ ÙÔ˘ ÂÚȯÔ̤ÓÔ˘ Ù˘ Û˘Û΢·Û›·˜ ™ÙË Û˘Û΢·Û›· ˘¿Ú¯Ô˘Ó: 1 E·Ó·ÊÔÚÙÈ˙fiÌÂÓÔ ‰ÈÛÎÔÚ›ÔÓfi 1 §Â›‰· ÚÈÔÓÈÔ‡ 1 ∞ÏÏÂÓfiÎÏÂÈ‰Ô 1 £‹ÎË Ì·Ù·ÚÈÒÓ (Ì ÚÔÛٷ٢ÙÈÎfi ÒÌ·) 1 ºÔÚÙÈÛÙ‹˜ 1 £‹ÎË (Ù‡· K ÌfiÓ·) 1 º˘ÏÏ¿‰ÈÔ Ô‰ËÁÈÒÓ 1 ∞Ó·Ï˘ÙÈÎfi Û¯¤‰ÈÔ • EϤÁÍÙ ÙÔ ÂÚÁ·Ï›Ô, Ù· ·ÓÙ·ÏÏ·ÎÙÈο Î·È Ù· ÂÍ·ÚÙ‹Ì·Ù· ÁÈ· ‚Ï¿‚˜ Ô˘ ›Ûˆ˜ ¤¯Ô˘Ó ÚÔÎÏËı› ηٿ ÙË ÌÂÙ·ÊÔÚ¿. • ∞ÊÈÂÚÒÛÙ ϛÁÔ ¯ÚfiÓÔ ÁÈ· Ó· ‰È·‚¿ÛÂÙÂ Î·È Ó· ηٷÓÔ‹ÛÂÙ fiÏÔ ÙÔ Ê˘ÏÏ¿‰ÈÔ Ô‰ËÁÈÒÓ ÚÈÓ Ó· ¯ÚËÛÈÌÔÔÈ‹ÛÂÙ ÙÔ ÂÚÁ·Ï›Ô. ¶ÂÚÈÁÚ·Ê‹ (ÂÈÎ.
∂§§∏¡π∫∞ ∞˘Ùfi Â›Ó·È Î·ÓÔÓÈ΋ ηٿÛÙ·ÛË Î·È ‰ÂÓ ·ÔÙÂÏ› Úfi‚ÏËÌ·. ªË ÊÔÚÙ›˙ÂÙ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ Û ıÂÚÌÔÎڷۛ˜ ÂÚÈ‚¿ÏÏÔÓÙÔ˜ < 4 ÆC ‹ > 40 ÆC. ™˘ÓÈÛÙÒÌÂÓË ıÂÚÌÔÎÚ·Û›· ÊfiÚÙÈÛ˘: ÂÚ›Ô˘ 24 ÆC. • °È· Ó· ÊÔÚÙ›ÛÂÙ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ (9), ‚¿ÏÙ ÙÔ ÛÙÔÓ ÊÔÚÙÈÛÙ‹ (10) fiˆ˜ Ê·›ÓÂÙ·È Î·È ‚¿ÏÙ ÙÔÓ ÊÔÚÙÈÛÙ‹ ÛÙË Ú›˙·. µÂ‚·Èˆı›Ù fiÙÈ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ ¤¯ÂÈ Î·ı›ÛÂÈ Î·Ï¿ ÛÙÔÓ ÊÔÚÙÈÛÙ‹. ∆Ô ÎfiÎÎÈÓÔ ÂÓ‰ÂÈÎÙÈÎfi ÊfiÚÙÈÛ˘ (11) ı· ·Ó·‚ÔÛ‚‹ÓÂÈ.
∂§§∏¡π∫∞ ºÔÚ¤ÛÙ ÚÔÛٷ٢ÙÈο Á˘·ÏÈ¿ fiÙ·Ó ‚¿ÏÂÙ ÙËÓ Ú›˙·. ∫·ı˘ÛÙ¤ÚËÛË ıÂÚÌÔ‡/ÎÚ˘Ô‡ Û˘ÛÛˆÚÂ˘Ù‹ √Ù·Ó Ô ÊÔÚÙÈÛÙ‹˜ ·ÓȯÓ‡ÛÂÈ Î¿ÔÈ· Ì·Ù·Ú›· Ô˘ Â›Ó·È ıÂÚÌ‹ ‹ ÎÚ‡·, ı· ÍÂÎÈÓ‹ÛÂÈ ·˘ÙfiÌ·Ù· ÙË ÏÂÈÙÔ˘ÚÁ›· ηı˘ÛÙ¤ÚËÛ˘ ıÂÚÌÔ‡/ÎÚ˘Ô‡ Û˘ÛÛˆÚÂ˘Ù‹, ·Ó·ÛÙ¤ÏÏÔÓÙ·˜ ÙËÓ ÊfiÚÙÈÛË ¤ˆ˜ Ë ıÂÚÌÔÎÚ·Û›· Ù˘ Ì·Ù·Ú›·˜ Â›Ó·È ·ÙË. EÂÈÙ· Ô ÊÔÚÙÈÛÙ‹˜ ı· ÂÚ¿ÛÂÈ ·˘ÙfiÌ·Ù· ÛÙË ÏÂÈÙÔ˘ÚÁ›· ÊfiÚÙÈÛ˘ Ù˘ Ì·Ù·Ú›·˜. ªÂ ÙÔÓ ÙÚfiÔ ·˘Ùfi ‰È·ÛÊ·Ï›˙ÂÙ·È Ë Ì¤ÁÈÛÙË ‰˘Ó·Ù‹ ˙ˆ‹ Ù˘ Ì·Ù·Ú›·˜.
∂§§∏¡π∫∞ • µÂ‚·Èˆı›Ù fiÙÈ Ë Ï›‰· ÙÔ˘ ÚÈÔÓÈÔ‡ ÂÚÈÛÙÚ¤ÊÂÙ·È Î·Ù¿ ÙË ÊÔÚ¿ ÙÔ˘ ‚¤ÏÔ˘˜ ÛÙËÓ Ï›‰·. • ªË ¯ÚËÛÈÌÔÔț٠˘ÂÚ‚ÔÏÈο Êı·Ṳ́Ó˜ Ï›‰Â˜. •ÂΛÓËÌ·/™Ù·Ì¿ÙËÌ· (ÂÈÎ. A) °È· ÏfiÁÔ˘˜ ·ÛÊ·Ï›·˜ Ô ‰È·ÎfiÙ˘ ÏÂÈÙÔ˘ÚÁ›·˜ on/off (1) ÙÔ˘ ‰ÈÛÎÔÚ›ÔÓÔ‡ Û·˜ Â›Ó·È ÂÍÔÏÈṲ̂ÓÔ˜ Ì ·ÛÊ·ÏÈÛÙÈÎfi ÎÔ˘Ì› (2). • ¶È¤ÛÙ ÙÔ ·ÛÊ·ÏÈÛÙÈÎfi ÎÔ˘Ì› ÁÈ· Ó· ··ÛÊ·Ï›ÛÂÙ ÙÔ ÂÚÁ·Ï›Ô. • °È· Ó· ÏÂÈÙÔ˘ÚÁ‹ÛÂÙ ÙÔ ÂÚÁ·Ï›Ô, ȤÛÙ ÙÔÓ ‰È·ÎfiÙË ÏÂÈÙÔ˘ÚÁ›·˜ on/off.
∂§§∏¡π∫∞ E°°À∏™∏ ¶ÂÚÈ‚¿ÏÏÔÓ • 30 ∏ªEƒø¡ E°°À∏™∏ π∫∞¡√¶√π∏∆π∫∏™ ∞¶√¢√™∏™ • E·Ó·ÊÔÚÙË˙fiÌÂÓÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ ∞˘Ùfi ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ Ì·ÎÚ¿˜ ‰È·ÚΛ·˜ Ú¤ÂÈ Ó· ÊÔÚÙ›˙ÂÙ·È fiÙ·Ó ‰ÂÓ ÌÔÚ› Ó· ·Ú¤¯ÂÈ ÈÛ¯‡ ÁÈ· ÂÚÁ·Û›Â˜ Ô˘ Á›ÓÔÓÙ·Ó Â‡ÎÔÏ· ÚÔËÁÔ˘Ì¤Óˆ˜. ∫·Ù¿ ÙÔ Ù¤ÏÔ˜ Ù˘ Ù¯ÓÈ΋˜ ÙÔ˘ ˙ˆ‹˜, ·ÔÚÚ›„Ù ÙÔ Ì ÙËÓ ‰¤Ô˘Û· ÊÚÔÓÙ›‰· ÁÈ· ÙÔ ÂÚÈ‚¿ÏÏÔÓ: • EÍ·ÓÙÏ‹ÛÙ ϋڈ˜ ÙÔ Û˘ÁÎÚfiÙËÌ· Ì·Ù·ÚÈÒÓ, Î·È ÛÙË Û˘Ó¤¯ÂÈ· ·Ê·ÈÚ¤ÛÙ ÙÔ ·fi ÙÔ ÂÚÁ·Ï›Ô. • ∆· ÛÙÔȯ›· NiCd/NiMH Â›Ó·È ·Ó·Î˘ÎÏÒÛÈÌ·.
Belgique et Luxembourg België en Luxemburg DEWALT Weihoek 1, Nossegem 1930 Zaventem-Zuid Tel: 02 719 07 11 Fax: 02 721 40 45 www.dewaltbenelux.com Danmark DEWALT Hejrevang 26 B 3450 Allerød Tlf: 70 20 15 30 Fax: 48 14 13 99 www.dewalt-nordic.com Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de EÏÏ¿˜ BLACK & DECKER (E§§∞™) ∞.E. ™ÙÚ¿‚ˆÓÔ˜ 7 & §ÂˆÊ. µÔ˘ÏÈ·Á̤Ó˘ 159 166 74 °Ï˘Ê¿‰· - ∞ı‹Ó· ∆ËÏ.