® DW004 DW005 1
6 7 5 DW005 4 11 9 10 8 3 2 1 9 A 3
12 9 12 9 B 3 3 DW004 C 4 DW005
6 7 13 D 4 E 5
4 F 2 G 6
ENGLISH CORDLESS ROTARY HAMMER DRILL DW004K/DW004K2/DW004K2C/DW004K2H/ DW005KH/DW005K2C/DW005K2H Congratulations! You have chosen a DEWALT power tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
ENGLISH Safety instructions When using Power Tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents. 2 Consider work area environment Do not expose Power Tools to humidity. Keep work area well lit.
ENGLISH Additional safety instructions for battery packs and chargers Fire hazard! Avoid metal short circuiting the contacts of a detached battery pack. Do not store or carry the battery pack without the battery cap placed over the contacts. • The battery fluid, a 25-30% solution of potassium hydroxide, can be harmful. In case of skin contact, flush immediately with water. Neutralize with a mild acid such as lemon juice or vinegar.
ENGLISH 5 6 7 8 9 Depth adjustment rod Dust cover Tool holder Release buttons Battery pack Charger Your DE0246 charger accepts DEWALT 24 V NiCd and NiMH battery packs. 9 Battery pack 10 Charger 11 Charging indicator Overload clutch In case of jamming of a drill bit, the drive to the drill spindle is interrupted. Because of the resulting forces, always hold the tool with both hands and take a firm stance. Brake mechanism When the variable speed switch is released, the spindle will stop rotating instantly.
ENGLISH Do not charge the battery pack at ambient temperatures < 4 °C or > 40 °C. Recommended charging temperature: approx. 24 °C. • To charge the battery pack (9), insert it into the charger (10) as shown and plug in the charger. Be sure that the battery pack is fully seated in the charger. The red charging indicator (11) will blink. After approx. 1 hour, it will stop blinking and remain on. The battery pack is now fully charged. • The red charging indicator flashes rapidly to indicate a charging problem.
ENGLISH Hammer drilling: for concrete and masonry drilling • Select the required operating mode by rotating the mode selector (3) towards the symbol on the gear housing. • For screwdriving, refer to section «Instructions for use». DW005 - Selecting the operating mode (fig.
ENGLISH • Apply only a gentle pressure to the tool. • Do not drill or drive too deep to prevent damage to the dust cover. Switching on and off (fig. A) • To run the tool, press the variable speed switch (1). The pressure exerted on the variable speed switch determines the tool speed. • To stop the tool, release the switch. Hammer drilling (fig. A) • Select the hammer drilling mode. • Insert the appropriate SDS-plus bit. For best results use high quality carbide-tipped bits.
ENGLISH Environment GUARANTEE • 30 DAY NO RISK SATISFACTION GUARANTEE • Rechargeable battery pack This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment: • Run the battery pack down completely, then remove it from the tool. • NiCd and NiMH cells are recyclable. Take them to your dealer or a local recycling station.
Belgique et Luxembourg België en Luxemburg DEWALT Weihoek 1, Nossegem 1930 Zaventem-Zuid Tel: 02 719 07 11 Fax: 02 721 40 45 www.dewaltbenelux.com Danmark DEWALT Hejrevang 26 B 3450 Allerød Tlf: 70 20 15 30 Fax: 48 14 13 99 www.dewalt-nordic.com Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de EÏÏ¿˜ BLACK & DECKER (E§§∞™) ∞.E. ™ÙÚ¿‚ˆÓÔ˜ 7 & §ÂˆÊ. µÔ˘ÏÈ·Á̤Ó˘ 159 166 74 °Ï˘Ê¿‰· - ∞ı‹Ó· ∆ËÏ.