INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. DW831, DW840 5" (125mm) and 7" (180mm) Heavy Duty Angle Grinder Rectifieuse coudée de service intensif de 127 mm (5 po) et 175 mm (7 po) Esmeriladora angular para trabajo pesado de 127 mm (5") y 175 mm (7") INSTRUCTION MANUAL GUIDE D'UTILISATION MANUAL DE INSTRUCCIONES Questions? See us on the World Wide Web at www.dewalt.
ELECTRICAL SAFETY • Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.
English • Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally. • Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
• • • • • • • • • injury. Accessory ratings must always be above tool speed as shown on tool nameplate. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. Do not use Type 11 Flaring Cup wheels on this tool. Using inappropriate accessories can result in injury.
English E D A B D. Side Handle E. Guard (Type 27, open beneath wheel or accessory) CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, depress and release the rear part of the switch to ensure that the tool is off. ASSEMBLY C COMPONENTS A. Trigger Switch B. Lock-On Button C. Spindle Lock Button INTRODUCTION • The label on your tool may include the following symbols.
Type 27 hubbed wheel Type 27 hubbed wheel 5 Type 27 guard clamp nut Type 27 non-hubbed wheel backing flange Type 27 guard 7" Grinding Wheels (DW840) Type 27 guard threaded clamp nut Type 27 depressed center wheel unthreaded backing flange Type 27 guard 5" Grinding Wheels (DW831) English
English threaded clamp nut non-hubbed sanding flap disc unthreaded backing flange Type 27 guard 6 hubbed sanding flap disc Type 27 guard Sanding Flap Discs CAUTION: Use a Type 27 guard with wire brushes and wheels. Operators and others in the area should wear appropriate eye, face and body protection. Strands of wire may break and fly off when wire wheels and brushes are in use.
10˚ - 30° WARNING: Edge grinding and cutting can be performed only with Type 27 wheels that are designed and specified for this purpose. Protect yourself during edge cutting by directing the open side of the guard toward a surface. WARNING: Wheels used for cutting and edge grinding may break or kick back if they bend or twist while the tool is being used to do cut-off work or deep grinding.
English B CAUTION: Unplug the tool before mounting or removing the guard. Guards must be used with all grinding wheels and sanding flap discs, wire brushes and wire wheels. The tool may be used without the guard only when sanding with conventional sanding discs. Before reconnecting the tool, depress and release the rear part of the switch to ensure that the tool is off. FITTING GUARD CAUTION: Do not operate grinder with a loose guard or the guard latch in the open position. 1.
CAUTION: Unplug the tool before mounting or removing the guard. Guards must be used with all grinding wheels and sanding flap discs, wire brushes and wire wheels. The tool may be used without the guard only when sanding with conventional sanding discs. Before reconnecting the tool, depress and release the rear part of the switch to ensure that the tool is off. FITTING GUARD CAUTION: Do not operate grinder with a loose FIG. 3 guard or the guard latch in the open position. 1.
English DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool DEWALT tools are properly lubricated at the factory and are ready for use. Tools should be relubricated regularly every sixty days to six months, depending on usage.
90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement.