DWE315
Figure 1 b d a c e f g t Figure 2 h c 1 1
Figure 3 Figure 4 Figure 5 Figure 6 j p l k i Figure 8 Figure 7 f e g m u f o p 2 Figure 9 n g
Figure 10 Figure 11 f n g g Figure 13 Figure 12 a Figure 14 Figure 15 d b a 3 3
Figure 16 q m p o e u Figure 17 Figure 18 q q r c i s 4
EN GLI S H OSCILLATING MULTI-TOOL DWE315 An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
E NG L I S H EC-Declaration of Conformity MACHINERY DIRECTIVE DWE315 DEWALT declares that these products described under Technical Data are in compliance with: 2006/42/EC, EN 60745-1, EN60745-2-4, EN60745-2-11. These products also comply with Directive 2004/108/EC and 2011/65/EU. For more information, please contact DEWALT at the following address or refer to the back of the manual. The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.
EN GLI S H e) f) g) wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
E NG L I S H stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. Residual Risks In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are: 1 9.5 mm x 43 mm Wood detail blade (DWE315K) 1 3 mm Carbide grout removal blade (100 mm half moon) (DWE315K) 1 Rigid scraper blade 1 Hex key 1 Kit box (DWE315K) 1 Kit bag (DWE315B) – Impairment of hearing.
EN GLI S H Electrical Safety The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate. Your DEWALT tool is double insulated in accordance with EN 60745; therefore no earth wire is required. WARNING: 115 V units have to be operated via a fail-safe isolating transformer with an earth screen between the primary and secondary winding.
E NG L I S H CAUTION: Read and follow all manufacturers' safety warnings for any accessories used with this tool. NOTE: The guide arm can also be placed in the guard assembly vertically in order to set the height off a cut. Refer to figure 12. CAUTION: To avoid injury, ensure adaptor and accessory are securely tightened. Attaching the Dust Extraction Adaptor (fig. 16) Non-DEWALT accessories can be attached using the universal adaptor. 1. Place the washer (k) on the tool. 2. Place accessory on to washer.
EN GLI S H Proper Hand Position (fig. 13) WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown. WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction. Proper hand position requires the tool to be held as shown in Figure 13. Using the Dust Extraction Adaptor with the Sanding Platen (fig. 17) 1. Attach the dust extraction adaptor (q). Refer to Attaching the Dust Extraction Adaptor. 2.
E NG L I S H Optional Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories.
EN GLI S H GUARANTEE DEWALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
E NG L I S H TROUBLESHOOTING PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Unit will not start. Cord not plugged in. Plug tool into a working outlet. Circuit fuse is blown. Replace circuit fuse. (If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced by an authorised DEWALT repair agent.) Circuit breaker is tripped. Reset circuit breaker.