Use and Care Manual

ManualsBrandsDEWALT ManualsMiter Saws15 Amp 12 in. Dual Bevel Sliding Compound Miter Saw with Bonus Heavy Duty Work Stand

English

Dust Bag: DW7053

Equipped with a zipper for easy emptying, the dust bag will capture the majority of the

sawdust produced.

Crown Molding Fence: DW7084

Used for precision cutting of crown molding.

SAW BLADES: ALWAYS USE 12" (305 mm) SAW BLADES WITH EITHER 1" (25.4 mm) OR

5/8" (15.88 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 4800 RPM. Never

use a smaller diameter blade. It will not be guarded properly. Use crosscut blades only!

Do not use blades designed for ripping, combination blades or blades with hook angles in

excess of 7°.

DW7080

LOCKNUTS

END PLATE

FIG. 1

DW7082

DW7051

BRACKET

KNOBS

BLADE DESCRIPTIONS

APPLICATION DIAMETER TEETH

Construction Saw Blades (thin kerf with anti-stick rim)

General Purpose 12" (305 mm) 40

Fine Crosscuts 12" (305 mm) 60

Woodworking Saw Blades (provide smooth, clean cuts)

Fine crosscuts 12" (305 mm) 80

Non-ferrous metals 12" (305 mm) 96

NOTE: For cutting non-ferrous metals, use only saw blades with

TCG (Triple Chip Grind) teeth designed for this purpose.

Unpacking Your Saw

Check the contents of your miter saw carton to make sure that you have received all parts.

In addition to this instruction manual, the carton should contain:

1 DWS709 miter saw

1 D

EWALT 12" (305 mm) diameter saw blade

In bag:

1 Blade wrench

1 DW7053 dustbag

1 Material clamp

Specifications

CAPACITY OF CUT

50º miter left, 60º miter right,

49º bevel left and right

HEIGHT WIDTH

0º Miter / 0º Bevel 4-1/2" (114 mm) 9-9/16" (243 mm)

45º Meter / 0º Bevel 4-1/2" (114 mm) 6-11/16" (171 mm)

50º Miter / 0º Bevel 4-1/2" (114 mm) 6-1/16" (155 mm)

60º Miter / 0º Bevel 4-1/2" (114 mm) 4-5/16" (110 mm)

45º Bevel - Left / 0º Miter 2-7/16" (62 mm) 9-9/16" (243 mm)

45º Bevel - Right / 0º Miter 1-11/16" (43 mm) 9-9/16" (243 mm)

Crown Flat (Spring Angle 38) 2-13/16" (72 mm) 8-1/16" (206 mm)

Crown Flat (Spring Angle 45) 1-1/4" (33 mm) 7-3/4" (198 mm)

NOTE: Your saw is capable of cutting the following once a special setup procedure is

followed. Refer to Special Cuts.

HEIGHT WIDTH

0º Miter / 0º Bevel 2-15/16" (75 mm) 13-3/8" (340 mm)

45º Meter / 0º Bevel 2-1/16" (53 mm) 9-13/16" (250 mm)

50º Miter / 0º Bevel 2-1/16" (53 mm) 9-1/8" (232 mm)

45º Meter - Left / 0º Miter 7/8" (23 mm) 9-9/16" (354 mm)

Crown Flat (Spring Angle 38) 7/8" (23 mm) 11-5/16" (288 mm)

Crown Flat (Spring Angle 45) 7/8" (23 mm) 10-7/8" (276 mm)

DW7053

DW7084