INSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND DWX724-XE COMPACT MITER SAW STAND
DWX723-XE/DWX724-XE MITER SAW STANDS Components List FIG. 1 A. Beam B. DW7231-XE Miter saw mounting brackets C. Extension arm D. DW7232-XE Work piece support and length stop E. Extension arm end cap F. Extension arm lock lever G. Release levers H. Carry handle I. Locking locator clip J. Leg lock lever K. Release button A B C 2 K I D G J H 1 DWX723-XE DWX724-XE 1 1765.3 mm (69.5") 1092.2 mm (43") 2 3835.
Tools Required Definitions: Safety Guidelines • Drill with 9.5 mm (3/8") drill bit (Not required for DEWALT Miter Saws) • Crosshead #2 screwdriver • 13 mm (1/2") Wrench The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
FIG. 2 Preparation (Fig. 2) b. Adjust the height of the work support/stop (D) by loosening the knobs on both sides (N) and raise or lower the top surface to align with a straight edge or level to the saw table. Tighten the knobs. NOTE: If the work support height adjustment slips down when under a load, the weight limit of the work support has been exceeded. This weight limit is limited by the tightness of the height adjustment knobs. Do not tighten more than finger tight. c.
3. Hold a mounting bracket under the saw and feed a carriage bolt (hardware bag) up through the bracket and the foot of the saw. NOTE: See DW7231-XE Hardware Selection Chart for the correct mounting hardware procedures for DEWALT miter saws. Follow all instructions properly, otherwise the miter saw's table rotation may be obstructed. 4. Once the carriage bolt (hardware bag) is installed per DW7231-XE Hardware Selection Chart, assemble a flat washer, lock washer and nut onto the bolt.
DW7231-XE Universal Miter Saw Mounting Method (Fig. 1, 7–9) 1. Once the Plywood size has been determined, drill 9.5 mm (3/8") holes 25.5 mm (1") from the front corners of plywood, 355 mm (15") apart and 25.5 mm (1") from the sides. 2. Place DW7231-XE mounting brackets on the stand: a. Grasp and squeeze release levers (G). b. Engage the concave front lip of the mounting bracket with rounded front edge of beam.
Carry Strap Recommended accessories for use with your tool are available at extra cost from your local service center. If you need any assistance in locating any accessory, please contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ). 0800 339 258. If you purchase the carry strap accessory for DEWALT stands, use the square hole in the metal end to mount the accessory. Locking Locator Clip (Fig.
Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.com.nz (NOV11) Part No. N150464 DWX723-XE, DWX724-XE Copyright © 2011 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.