Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting Operator’s Manual 33” Wide Cut Mower Table of Contents Safe Operation Practices......................................... 2 Assembly & Set-Up................................................... 8 Controls & Features.................................................10 Operation.................................................................13 Maintenance & Adjustment..................................16 Service...........
Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.
7. Never operate mower without the proper trail shield, discharge cover, grass catcher, blade control or other safety protective devices in place and working. Never operate mower with damaged safety devices. Failure to do so can result in personal injury. 8. Never operate mower in bare feet, sandals, slippery or light-weight (e.g. canvas) shoes. When starting engine, pull cord slowly until resistance is felt, then pull rapidly.
Children 1. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the mower and the mowing activity. They do not understand the dangers. Never assume that children will remain where you last saw them. 2. Keep bystanders, children and pets inside while the mower is in operation under watchful care of a responsible adult other than the operator. Stop mower if anyone enters the area. 3.
Service 1. Keep the mower in good working order. Replace worn or damaged parts. 2. To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting of engine governor. Do not change the engine governor settings or over-speed the engine. The governor controls the maximum safe operating speed of the engine. 3. Mower blades are sharp.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate. DANGER — ROTATING BLADES To reduce the risk of injury, keep hands and feet away.
(OK) Figure 1 Slope Gauge dashe d 15°/25% Slope 5% 15°/2 USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.) 3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ). 4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2). 5.
3 Assembly & Set-Up Contents of Crate • Lawn Mower (1) • Oil Drain Hose (1) • Lawn Mower Operator’s Manual (1) • Engine Operator’s Manual (1) • Key (1) Mower Set-Up Attaching the Battery Cables (for Electric Start Models) Shipping Brace Removal NOTE: The positive battery terminal is marked Pos. (+). The negative battery terminal is marked Neg. (–). WARNING! Make sure the lawn mower’s engine is OFF. Remove the ignition key (if equipped) before removing the shipping brace. 1. 1.
Unfolding the Handle Attaching the Shift Lever 1. 1. Remove the star knobs (a) and carriage screws (b) from the lower handle. See Figure 3-3. Remove the screw (a) and the lock nut (b) that secures the shift lever to the shift lever plate. See Figure 3-5. (c) (a) (d) (b) Figure 3-5 2. Remove the remaining screw (c) and nut (d) from the lower shift lever plate. See Figure 3-5. 3.
4 Controls and Features Throttle Control Blade Control Fuel Tank Cap Ignition Switch† Deck Height Lever LCD Service Minder and Hour Meter† Drive Control Gear Shift Lever † If Equipped Figure 4-1 Lawn Mower controls and features are illustrated in Figure 4-1 and described on the following pages. WARNING! Read and follow all safety rules and instructions in this manual, including the entire Operation section, before attempting to operate this machine.
Ignition Switch Blade Control WARNING! Never leave a running machine unattended. Always disengage blades, stop engine and remove key to prevent unintended starting. Run Position Stop Position Located on the right-hand handle, the blade control is used to engage the mowing deck. To operate, press and hold the lever against the handlebar grip. To stop the blades, release the blade control. WARNING! Never attempt to start the engine with the blade control engaged.
LCD Service Minder and Hour Meter Change Oil (Electric Start Models Only) The LCD will display the letters “CHG”, followed by the letters “OIL”, followed by the letters “SOON”, then finally followed by the meter’s accumulated time. “CHG/OIL/SOON/TIME” will alternate on the display for seven minutes after the meter reaches 50 hours. This oil service minder interval will occur every 50 hours for the following two hours.
5 Operation Gas and Oil Recoil Start The fuel tank has a capacity of two gallons. Remove the fuel cap by turning it counter-clockwise. Use only clean, fresh (no more than 30 days old), unleaded gasoline. Fill the tank no higher than four inches below the top of the filler neck to allow space for fuel expansion. Refer to the Set-Up and Assembly section of this manual for gasoline and oil fill-up instructions. WARNING! Use extreme care when handling gasoline.
Engaging the Drive WARNING! Avoid sudden starts, excessive speed and sudden stops. 1. Start the engine as instructed earlier in this section and move the throttle/choke control into the FAST (rabbit) position. 2. To travel FORWARD: a. b. Place the gear shift lever in any of the four Forward ground speeds. Select a speed appropriate for the conditions and a pace you’re comfortable with. Slowly squeeze the drive control against the left handle grip and the mower will move.
Mowing Installing / Removing Mulch Baffle WARNING! Before installing or removing the mulch plug, disengage blades, stop the engine and remove key (if equipped) to prevent unintended starting. The following information will be helpful when operating your mower. WARNING! Plan your mowing pattern to avoid discharge of materials toward roads, sidewalks, bystanders and the like.
6 Maintenance & Adjustments Maintenance Schedule Each use or every 5-10 Hrs.
Spark Plug Smart Jet The spark plug should be cleaned and the gap reset every 25 hours or once a season. Refer to the Engine Operator’s Manual for correct plug type and gap specifications. Your mower’s deck is equipped with a water port on its surface as part of its deck wash system. Fuel Filter The fuel filter cannot be cleaned and should be replaced every 100 operating hours; more often if run with old gasoline.
Lubrication Blade Timing Belt WARNING! Before lubricating, repairing, or inspecting, always disengage PTO, set parking brake, stop engine and remove key (if equipped) to prevent unintended starting. The cutting deck spindles are driven by a blade timing (cogged) belt, assuring that the deck blades are always perpendicular to each other. At least once a season, or after striking any foreign object, check the timing belt as follows: 1.
2. The top of each spindle pulley is marked with an arrow. See Figure 6-4. The arrows should be perpendicular (at a 90˚ angle) to each other. Adjustments WARNING! Shut the engine OFF and remove the ignition key (if equipped) before making adjustments. Handle Height The upper handle is secured to two support bars that can be adjusted to raise or lower the handle height. Adjust if necessary as follows: 1.
Service Cutting Deck Removal WARNING! Before performing any maintenance or repairs, disengage blades, stop engine and remove key (if equipped) to prevent unintended starting. 2. Place the deck height lever in its highest position. 3. Position wood blocks at various places under the deck’s edge. These will temporarily support the deck as it is removed. 4. Use the deck height lever to lower the deck, so that it rests on the wood blocks. 5.
8. Repeat the Step 7 on the mower’s right side. 9. Carefully remove the front deck supports from the deck lift arms. See Figure 7-3. 10. Carefully unhook the mower’s lift assembly from the rear deck supports. 11. Use the deck height lever to raise the lift assembly to its highest position. 12. Remove the wooden blocks from under the deck and gently slide the cutting deck toward the rear of the machine. 13.
5. Test the blade’s balance using a blade balancer. Grind metal from the heavy side until it balances evenly. Battery CALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Changing the Deck Engagement Belt Changing the Deck Timing Belt WARNING! Shut the engine OFF and remove key (if equipped) before removing the cutting blade(s) for sharpening or replacement. Protect your hands by using heavy gloves when grasping blades and pulleys. Several components must be removed and special tools used in order to change the mower deck’s timing belt. See your authorized service dealer to have the deck’s timing belt replaced.
8 Troubleshooting Problem Engine fails to start Remedy 1. Place throttle/choke control in CHOKE position. 2. Fuel tank empty, or stale fuel. 2. Fill tank with clean, fresh (less than 30 days old) gas. 3. Blocked fuel line. 3. Clean fuel line and replace fuel filter. Refer to Engine Operator’s Manual. 4. Faulty spark plug. 4. Clean, adjust gap or replace plug. Refer to Engine Operator’s Manual. 5. Engine flooded. 5. Crank engine with throttle in FAST position. 6.
Medidas importantes de seguridad • Configuración • Funcionamiento • Mantenimiento • Servicio • Solución de problemas • Garantía Manual del operador Cortadora de césped de 33 pulgadas de área amplia Table of Contents Importante Medidas importantes de seguridad.26 Mantenimiento y Ajustes....................................... 40 Montaje y Configuración....................................... 32 Servicio.................................................................... 45 Controles y Características........
2 Medidas importantes de seguridad ADVERTENCIA: La presencia de este símbolo indica que se trata de instrucciones importantes de seguridad que se deben respetar para evitar poner en peligro su seguridad personal y/o material y la de otras personas. Lea y siga todas las instrucciones de este manual antes de poner en funcionamiento esta máquina. Si no respeta estas instrucciones puede provocar lesiones personales.
3. Esté atento a la cortadora de césped y a la dirección de descarga de los aditamentos y no apunte la descarga de la cortadora en dirección a nadie. 4. Para protegerse los ojos, utilice siempre gafas o anteojos de seguridad mientras opera la máquina y mientras la ajusta o repara. Los objetos arrojados que rebotan pueden producir lesiones graves en los ojos. 5. Utilice zapatos de trabajo resistentes, de suela fuerte, y pantalones y camisas ajustados.
Niños 4. 1. Si el operador no está atento a la presencia de niños, se pueden producir accidentes trágicos. Por lo general a los niños les atraen las cortadoras y la actividad de cortar el césped. Los niños no son conscientes de los peligros. Nunca asuma que los niños permanecerán donde los vio por última vez. Siempre corte el césped de forma transversal a la pendiente, nunca hacia arriba y hacia abajo. 5.
12. 13. 14. Nunca llene los recipientes en el interior de un vehículo o camión o caja de remolque con recubrimientos plásticos. Siempre ubique los recipientes en el piso, lejos del vehículo antes de llenarlos. Cuando sea factible, retire el equipo a gasolina del camión o remolque y apóyelo en el suelo para llenarlo. Si esto no es posible, recargue combustible sobre el remolque con un recipiente portátil, en lugar de una boquilla dosificadora de gasolina.
Símbolos De Seguridad Esta página representa y describe la seguridad los símbolos que pueden parecer en este producto. Lea, comprenda, y siga todas instrucciones de la máquina antes de intentar ensamblar y operar. Símbolo Descripción LEA EL MANUAL(S) DEL OPERADOR Lea, comprenda, y siga todas instrucciones en el manual (manuales) antes de operar el producto. PELIGRO— GIRANDO HOJAS Para reducir el riesgo de herida, guarde manos y pies lejos.
Sección 2 — Medidas importantes de seguridad Figura 1 iscon tinua nea d 15° lí 15° Pendiente ADVERTENCIA! Las pendientes son un factor importante relacionado con resbalones y caídas de accidentes que pueden resultar en lesiones o la muerte. La máquina es pesada y puede acelerar cuando se va cuesta abajo. Esté preparado para mantener el control de la máquina. Para evitar la perdida de control, opere a través de las pendientes, no hacia arriba y hacia abajo.
3 Montaje y Configuración Contenido del cajón • Una cortadora de césped • Un tubo de drenaje de aceite • Un Manual del operador de la cortadora de césped • Un Manual del operador del motor Configuración de la cortadora de césped Extracción de la traba de seguridad utilizada en el envío ¡ADVERTENCIA! Asegúrese de que el motor de la cortadora de césped esté apagado. Quite la llave de encendido antes de retirar la traba de seguridad utilizada en el envío. 1.
Despliegue de la manija 1. Extraiga las perillas en estrella y los tornillos del carro de la manija inferior. Vea Figura 3-3. Figura 3-5 2. Extraiga el tornillo y la tuerca restantes de la placa de la palanca de cambios inferior. Vea Figura 3-5. 3. Coloque la palanca de cambios superior en posición vertical alineando los orificios de la palanca con los de la placa de cambios. Vea FiguraFigura 3-6. Figura 3-3 2. Gire la manija superior a la posición de funcionamiento.
4 Controles y Características Control del regulador Control de las cuchillas Tapón del tanque de combustible Palanca de altura de la plataforma Interruptor de encendido† Servicio LCD Minder y Cronómetro† Control de la transmisión Palanca de cambios † Si Equipada Figure 4-1 Los controles y características de la cortadora de césped se ilustran en Figure 4-1 y se describen en las páginas siguientes.
Interruptor de encendido Control de las cuchillas ¡ADVERTENCIA! Nunca deje la máquina en funcionamiento sin vigilancia. Siempre desenganche las cuchillas, apague el motor y retire la llave, para evitar el encendido accidental del motor. El interruptor de tres posiciones se usa para encender y apagar el motor de los modelos con arranque eléctrico. Vea Figura 4-2. Ubicado en la manija derecha, el control de las cuchillas se usa para enganchar la plataforma de corte.
Servicio LCD Minder y Cronómetro (Modelos de Arranque Eléctrico Sólo) Cambio De Aceite La pantalla mostrará las letras “CHG”, seguido de las letras “OIL”, seguido de las letras “pronto”, y finalmente seguido por el tiempo acumulado del metro. “CHG / OIL / PRONTO / TIME” se alternará en la pantalla durante 7 minutos después de que el metro llegue a 50 horas para las dos horas siguientes. Este servicio cuidadora intervall petróleo ocurrirá cada 50 horas.
5 Funcionamiento Gasolina y aceite Retroceso de inicio El tanque de combustible tiene capacidad para dos galones. Quite la tapa de combustible girándola en sentido contrario al de las agujas del reloj. Utilice únicamente gasolina limpia, nueva (no más de 30 días de uso) y sin plomo. Llene el tanque a no más de cuatro pulgadas por debajo del borde superior del cuello de llenado para permitir la expansión del combustible.
2. Para conducir hacia ADELANTE: a. Coloque la palanca de cambios en cualquiera de las cuatro velocidades de avance. Seleccione una velocidad adecuada a las condiciones y con la cual se sienta cómodo. b. Oprima el control de la transmisión. c. Oprima lentamente el control de la transmisión contra la manija de la empuñadura y la cortadora se moverá. Suéltelo y se detendrá el movimiento de la transmisión. Para conducir hacia ATRÁS: a. Verifique que el área detrás suyo está despejada. b.
Abono Las cortadoras de césped anchas vienen equipadas con un kit para abono que incorpora cuchillas especiales, que vienen de serie en su cortadora, para recircular los recortes de césped repetidas veces por debajo de la plataforma de corte. Los recortes muy finos luego son despedidos hacia atrás para que se depositen en el césped y actúen como fertilizante natural. Observe los siguientes puntos para obtener los mejores resultados al realizar el abono.
6 Mantenimiento y Ajustes Calendario de mantenimiento Cada uso o cada 5-10 Horas Limpie las cortadoras Inspeccione el nivel de aceite del motor Controle el filtro de aire Cada 10 horas Cada tempo- Cada tempo- Cada temporada o cada rada o cada rada o cada 25 horas 50 horas 100 horas P P P P P Reemplace el elemento del filtro de aire † P Cambie el aceite del motor †† P Limpie los bornes de la batería P Lubrique las ruedas y rueditas delanteras de la plataforma Lubrique los puntos de pivote P P
Mantenimiento ¡ADVERTENCIA! Antes de realizar cualquier mantenimiento o reparación, desconecte las cuchillas, apague el motor y retire la llave para evitar el encendido accidental del motor. Motor Consulte las instrucciones y procedimientos específicas relativas a su motor de mantenimiento del motor en el Manual del propietario Motor. Con fines ilustrativos, el motor Briggs & Stratton se muestra en las figuras siguientes.
Batería 1. ADVERTENCIA PROPOSICIÓN 65 DE CALIFORNIA: Los bornes de la batería y los accesorios afines contienen plomo y compuestos de plomo, sustancias químicas que según lo establecido por el Estado de California causan cáncer y daños en el sistema reproductivo. Lávese las manos después de estar en contacto con estos componentes. PRECAUCIÓN: Asegúrese de que el canal de descarga de la cortadora está orientado ALEJADO de la casa, el garaje, los vehículos estacionados, etc. 2.
Lubricación Correa de sincronización de la cuchilla ¡ADVERTENCIA! Antes de lubricar, reparar o inspeccionar, desconecte la potencia de arranque (PTO), coloque el freno de mano, apague el motor y retire la llave, para evitar el encendido accidental del motor. Puntos de pivote y varillaje Lubrique todos los puntos de pivote del sistema de transmisión y el varillaje de elevación con aceite ligero por lo menos una vez por temporada.
2. La parte superior de cada polea de husillo está marcada con una flecha. Vea Figura 6-66. Las flechas deben estar perpendiculares (a un ángulo de 90˚) entre sí. Ajustes ¡ADVERTENCIA! Apague el motor y retire la llave de encendido (si está equipado )antes de realizar ajustes. Altura de la manija La manija superior está sujeta a dos barras de apoyo que se pueden ajustar para subir o bajar la altura de la manija. De ser necesario, realice un ajuste de la siguiente manera: 1.
7 Servicio ADVERTENCIA: No haga funcionar la unidad sin tener la cubierta de la correa instalada. Si no se observan estas instrucciones se pueden producir lesiones personales o daños materiales. Extracción de la plataforma de corte ¡ADVERTENCIA! Antes de realizar cualquier mantenimiento o reparación, desconecte las cuchillas, apague el motor y retire la llave para evitar el encendido accidental del motor. Para extraer la plataforma de corte, proceda de la siguiente manera: 1.
Brazo de elevación Cuchillas de corte ¡ADVERTENCIA! Apague el motor y extraiga la llave de contacto (si está equipado) antes de retirar las cuchillas de corte para afilarlas o reemplazarlas. Proteja sus manos utilizando guantes reforzados cuando sujete las cuchillas. ¡ADVERTENCIA! Inspeccione periódicamente la cuchilla y/o el husillo en busca de rajaduras o daños, especialmente después de golpear un objeto extraño. No opere la máquina hasta después de haber reemplazado los componentes dañados.
PRECAUCIÓN: Si el borde de corte de la cuchilla ha sido afilado previamente o si existe una separación de metal, reemplace las cuchillas por otras nuevas. Batería ADVERTENCIA PROPOSICIÓN 65 DE CALIFORNIA: Los bornes de la batería y los accesorios afines contienen plomo y compuestos de plomo, sustancias químicas que según lo establecido por el Estado de California causan cáncer y daños en el sistema reproductivo. Lávese las manos después de estar en contacto con estos componentes.
Carga de la batería ¡ADVERTENCIA! Al cargarse, las baterías emiten un gas que puede causar explosiones. Cargue la batería en un área bien ventilada y manténgala alejada de una llama expuesta o piloto, como los de los calentadores de agua, calefactores de ambiente, hornos, secadores de ropa y otros aparatos a gas. Poleas locas de la plataforma PRECAUCIÓN: Cuando cargue la batería de la cortadora, utilice únicamente un cargador diseñado para baterías de plomo-ácido de 12V.
8 Solución de Problemas Problema El motor no arranca El motor funciona de manera errática Solución 1. Coloque el control del regulador/cebador en la posición CHOKE (cebador). 2. El depósito de combustible está vacío o el combustible se ha echado a perder. 2. Llene el depósito con gasolina limpia y nueva (de menos de 30 días). 3. La línea del combustible está bloqueada. 3. Limpie la línea de combustible y reemplace el filtro de combustible. 4. La bujía no funciona correctamente. 4.
Notes
Notes