If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarious, contéctenos. a 855-805-5745 • www.dewalt.com INSTRUCTION MANUAL GUIDE DE’UTILISATION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA, ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
English Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Assembly CONTENTS • Remove the heater and all of the packaging material from the box. • Remove and retain the four handle mounting screws that are threaded into the top shell. • Throughly inspect the heater for damage. If any is found do not contact the place of purchase. Please call the Manufacturer at 855-805-5745. • Use the four handle mounting screws to fasten the handle to the top of the heater Note: Do not over tighten the screws as they can crack the handle.
WHEEL KIT ASSEMBLY CONTENTS ITEM# ITEM DESCRIPTION QTY 1 40857 Handle Assembly 1 2 21875 Carriage Assembly 1 3 21897 Axle Assembly 1 4 40859 Wheels Assembly 2 5 41076 Base Plate 1 6 28787 Hardware Kit 1 Screws, w/nuts Wheel Spacer Hub Cap Large Washer Cotter Pin Base Plate Bolts 4 2 2 2 2 4 Tools Needed English REF# Hardware Kit Includes Step 2. Step 1. Remove bottom panel off heater and reuse same screws to install the base plate that is provided in the kit. Step 3.
English Starting Instructions, After Heater Has Been Professionally Wired • A soft dry cloth should be used for cleaning of outer shell and handle. • The fan motor is sealed and does not need to be lubricated. Specifications 1. Place the heater on a stable and level surface. Insure clearance to combustibles are observed (see table on this page). 2. Turn thermostat counter-clockwise to lowest setting. 3. Move 4 way selector switch from the off position to the fan position for fan only operation. 4.
Storage Note: Your heater is equipped with auto cool down and warm-up features. AUTO COOLDOWN. When the heater is running and the selector switch is rotated to the off position, the heater will automatically keep the fan operating until the heater is cool. The fan will then shut off. When not in use, the heater must be disconnected from power source, dusted off and the cord should be loosely wound around the handle. WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS.
DXH2003TS DXH2000TS English Wiring Diagrams 7
Parts List DXH2000TS REF. #...................ITEM#............ DESCRIPTION 1..........................N/A......................COVER, TOP, SHELL, OUTER 2..........................N/A......................PANEL, FRONT 3..........................N/A......................PANEL, REAR 4..........................N/A......................SHIELD, RADIATION, TUBE 5..........................N/A......................BASE, PLATE 6..........................N/A......................PANEL, SIDE, LEFT 7...
English DXH2000TS 8 9
Parts List DXH2003TS REF. #...................ITEM#............ DESCRIPTION 1..........................N/A......................COVER, TOP, SHELL, OUTER 2..........................N/A......................PANEL, FRONT 3..........................N/A......................PANEL, REAR 4..........................N/A......................SHIELD, RADIATION, TUBE 5..........................N/A......................BASE, PLATE 6..........................N/A......................PANEL, SIDE, LEFT 7...
English DXH2003TS 11
Warning: Use only manufacturer’s replacement parts. Use of any other parts could cause injury or death. Replacement parts are only available direct from the factory and must be installed by a qualified service agency. PURCHASING: Accessories may be purchased at any DeWalt® local dealer or direct from the factory INSTRUCTION MANUAL FOR INFORMATION REGARDING SERVICE: Electric Forced-Air Heater DXH2000TS, DXH2003TS Please call Toll-Free 855-805-5745 www.dewalt.
If you have questions or comments, contact us. Si vous avez des questions ou commentaires, veuillez nous contacter. Llámenos si tiene alguna pregunta o comentario. 855-805-5745 • www.dewalt.com INSTRUCTION MANUAL MANUEL D’INSTRUCTIONS MANUAL DE INSTRUCCIONES Electric Forced Air Heater DXH2000TS and DXH2003TS Appareil de chauffage à air forcé électrique modèles DXH2000TS et DXH2003TS Calentador eléctrico a aire forzado DXH2000TS y DXH2003TS READ INSTRUCTIONS CAREFULLY: Read and follow all instructions.
Français Définitions : Directives de sécurité Les définitions ci-dessous décrivent le niveau de sévérité pour chaque mot signalétique. Veuillez lire le manuel et faire attention à ces symboles. DANGER : Indique « une situation à risque imminent, laquelle, si elle n’est pas évitée, entraînera des blessures sérieuses ou la mort ». AVERTISSEMENT : Indique « une situation à risque potentiel, laquelle si elle n’est pas évitée, pourrait entraîner des blessures sérieuses ou la mort ».
Assemblage TABLE DES MATIÈRES • Enlevez l’appareil de chauffage et tout le matériel d’emballage de la boîte. • Enlevez et mettez de côté les quatre vis de montage de la poignée qui sont filetées dans la coque supérieure. • Inspectez à fond l’appareil de chauffage pour en déceler tout dommage. Si vous en trouvez, ne communiquez pas avec le lieu d’achat. Communiquez plutôt avec le fabricant au 855-8055745.
ENSEMBLE ROUE KIT CONTENU ARTICLE# DESCRIPTION DE ARTICLES QTY 1 40857 Poignée Assemblée 1 2 21875 Carriage Assembly 1 3 21897 Assemblée Axle 1 4 40859 Assemblée Roues 2 5 41076 Plaque de Base 1 6 28787 Hardware Kit 1 Vis avec écrous roue Spacer Hub Cap Grande Rondelle Goupille Boulons de plaque de base 4 2 2 2 2 4 Kit de Hardware Comprend Outils Requis Français REF# Step 2. Step 1.
Français Instructions de démarrage, après que l’appareil de chauffage ait été câblé professionnellement Spécifications 1. Placez l’appareil sur une surface plane et à niveau. Assurez-vous que l’espace libre entre tout combustible soit respecté (voir la table sur cette page). 2. Tournez le thermostat dans le sens contraire des aiguilles d’une montre à sa plus basse position. 3.
Entreposage Remarque : Votre appareil de chauffage est équipé avec des options de refroidissement et de chauffage automatiques. Lorsque l’appareil de chauffage n’est pas utilisé, il doit être débranché de la source de tension, épousseté et le cordon doit être grossièrement enroulé autour de la poignée. Pour l’entretien : Veuillez appeler sans frais le 855-805-5745 www.dewalt.com Nos heures de bureau sont de 8 h 00 à 17 h, fuseau horaire de l’est, du lundi au vendredi.
7 PCB1 = Circuit imprimé avec indicateur DEL « en marche » M = Moteur de ventilateu r L = Lampe de l'indicateur du ventilateur « en marche » CB1 - CB6 = Disjoncteurs 1 à 6 (30 ampères) MC1 = Condensateur du moteu r DXH2000TS R1 - R9 = Éléments chauffant s PCB1 = Circuit imprimé avec indicateur DEL « en marche » = = = Lampe de l'indicateur du ventilateur « en marche » L M = Moteur de ventilateu r MC1 = Condensateur du moteur Position du Commutateur SCHÉMA DE CÂBLAGE MODÈLE DXH2003TS SW1 = Interrupteur
Liste des pièces DXH2000TS RÉF. #...................ITEM#................DESCRIPTION 1..........................N/A......................COUVERCLE, HAUT, COQUE, EXTÉRIEUR 2..........................N/A......................PANNEAU, AVANT 3..........................N/A......................PANNEAU, ARRIÈRE 4..........................N/A......................ÉCRAN, RADIATION, TUBE 5..........................N/A......................BASE, PLAQUE 6..........................N/A......................
Français DXH2000TS 8 9
Liste des pièces DXH2003TS RÉF. #...................ITEM#................DESCRIPTION 1..........................N/A......................COUVERCLE, HAUT, COQUE, EXTÉRIEUR 20........................41092.................SUPPORT, COMMUTATUR, VENTILATEUR, REFROID. 21........................N/A .....................SUPPORT, MONTAGE DE CÂBLES 22........................N/A .....................SUPPORT, BORNIER, CÂBLAGE 23........................41051.................PORTE, ACCÈS 24........................
Français DXH2003TS 11
AVERTISSEMENT : N’utilisez que les pièces de remplacement du fabricant. L’utilisation d’autres pièces risque de causer des blessures et la mort. Les pièces de remplacement ne sont offertes que directement de l’usine et doivent être installées par une entreprise de service spécialisée. ACHAT : Les accessoires peuvent être achetés chez n’importe quel revendeur local DeWalt® ou directement à l’usine.
If you have questions or comments, contact us. Si vous avez des questions ou commentaires, veuillez nous contacter. Llámenos si tiene alguna pregunta o comentario. 855-805-5745 • www.dewalt.com INSTRUCTION MANUAL MANUEL D’INSTRUCTIONS MANUAL DE INSTRUCCIONES Electric Forced Air Heater DXH2000TS and DXH2003TS Appareil de chauffage à air forcé électrique modèles DXH2000TS et DXH2003TS Calentador eléctrico a aire forzado DXH2000TS y DXH2003TS READ INSTRUCTIONS CAREFULLY: Read and follow all instructions.
Español Definiciones: Indicaciones de seguridad Las siguientes definiciones describen el nivel de severidad para cada una de estas señales. Lea el manual y preste atención a estos símbolos. PELIGRO: Indica una situación inminente de peligro, la que si no se evita, causaría heridas graves o la muerte. ADVERTENCIA: Indica una situación potencial de peligro, la que si no se evita, podría causar heridas graves o la muerte.
Armado ÍNDICE • Saque el calentador y todos los materiales de embalaje de la caja. • Retire y conserve los cuatro tornillos de montaje del asa que están atornillados a la cubierta superior. • Revise bien que el calentador no esté dañado. Si encuentra algún daño, no se ponga en contacto con el lugar donde lo compró. Llame al Fabricante al 855-805-5745. • Utilice los cuatro tornillos de montaje del asa para atornillar el asa a la parte superior del calentador.
ENSAMBLAJE KIT DE RUEDA CONTENIDOS REF# DESCRIPCIÓN DEL ARTÍCULO QTY 40857 Ensamble de Manija 1 2 21875 Montaje del Carro 1 3 21897 Asamblea Axle 1 4 40859 Asamblea Ruedas 2 5 41076 Plato Base 1 6 28787 Kit de Hardware 1 Tornillo , con Tuercas Rueda Spacer Tapacubos Arandela Grande Pasador de Chaveta Pernos de la Placa de Base 4 2 2 2 2 4 Herramientas requeridas Español ARTÍCULO# 1 Kit de Hardware Incluye Step 2. Step 1.
Español Instrucciones de encendido, tras la conexión profesional del calentador Especificaciones Modelo: 1. Coloque el calentador en una superficie plana y estable. Asegúrese de respetar las recomendaciones de separación con respecto a materiales combustibles (ver tabla en esta página). 2. Gire el termostato en sentido contra horario hasta el valor mínimo. 3. Mueva el selector de 4 posiciones desde la posición de apagado a la posición del ventilador para hacer funcionar el ventilador solamente. 4.
Almacenamiento Nota: Su calentador está equipado con funcionalidades de enfriamiento y calentamiento automáticas. Cuando no se esté usando, el calentador debe desconectarse de la fuente de alimentación, desempolvarse, y el cable debe enrollarse en el asa sin apretarlo. Para obtener servicio: Llame sin cargo al 855-805-5745, www.dewalt.com Nuestro horario de trabajo es de 8:00 AM a 5:00 PM, de lunes a viernes, hora del este.
7 PCB1 = Indicador LED de calefacción encendida impreso en la placa del circuito M = Motor del ventilador L = Lámpara indicadora de ventilador encendido CB1 - CB6 = Llaves térmicas de la 1 a la 6 (30 amp) MC1 = Capacitor del motor DXH2000TS R1 - R9 = Elementos calefactore s PCB1 = Indicador LED de calefacción encendida impreso en la placa del circuito L = Lámpara indicadora de ventilador encendid o M = Motor del ventilador MC1 = Capacitor del motor Posición del Interruptor DIAGRAMA DE CABLEADO DEL MODE
Lista de partes DXH2000TS REF.................. ARTÍCULO..............DESCRIPCIÓN 1..........................N/A......................CUBIERTA, SUPERIOR, EXTERNA 2..........................N/A......................PANEL, FRONTAL 3..........................N/A......................PANEL, TRASERO 4..........................N/A......................PANTALLA, RADIACIÓN, TUBO 5..........................N/A......................BASE, PLACA 6..........................N/A......................
Español DXH2000TS 9
Lista de partes DXH2003TS REF.................. ARTÍCULO..............DESCRIPCIÓN 1..........................N/A......................CUBIERTA, SUPERIOR, EXTERNA 2..........................N/A......................PANEL, FRONTAL 3..........................N/A......................PANEL, TRASERO 4..........................N/A......................PANTALLA, RADIACIÓN, TUBO 5..........................N/A......................BASE, PLACA 6..........................N/A......................
Español DXH2003TS 11
Advertencia: Use solamente partes de repuesto del fabricante. El uso de cualquier otra parte podría causar heridas o la muerte. Las partes de repuesto están disponibles únicamente en la fábrica y deben ser instaladas por una agencia de servicio calificada.