Use and Care Manual

ENGLISH
14
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.
Register online at www.dewalt.com
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthis.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
Repairs

WARNING:To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a
DeWALT
factory service center or a
DeWALT
authorized service center. Always use identical
replacementparts.
To find the nearest service center, please contact
DeWALT
, call
1-877-362-4271.
Accessories

DANGER: Risk of fluid injection. When using
replacement spray wands or guns with this pressure
washer, DO NOT use a spray wand and/or spray gun/
wand combination that is shorter in length than what
was provided with this pressure washer as measured
from the nozzle end of the wand to the guntrigger.

WARNING: Since accessories, other than those offered
by
DeWALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT
recommended
accessories should be used with thisproduct.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact
DeWALT
, call 1-877-362-4271.
2. After adding a gasoline stabilizer, run the engine
outdoors for 10 minutes to be sure that treated gasoline
has replaced the untreated gasoline in thecarburetor.
3. Turn the fuel valve to the OFFposition.
4. Continue to run the engine until it stops from the lack of
fuel in the carburetor fuel bowl. Running time should be
less than 3minutes.
Pump
The manufacturer recommends using
DeWALT
Pump Guard
or equivalent when storing the unit for more than 30 days
and/or when freezing temperatures are expected.
DeWALT
Pump Guard is environmentallyfriendly.
NOTE: Using pump guard helps provide proper lubrication
to the internal seals of the pump regardless of temperature
or environment.
NOTICE: Risk of property damage. Use only
DeWALT
Pump Guard or equivalent. Other products could be
corrosive and/or contain alcohol which may cause
pumpdamage.
1. Turn off pressure washer and disconnect hoses
frompump.
2. Unscrew bottle valve from Pump Guard bottle and
remove seal.
3. Screw bottle valve back ontobottle.
4. Attach bottle to water inlet ofpump.
5. Squeeze bottle to inject contents intopump.
6. With ignition switch off, simultaneously pull starter rope
and squeeze bottle. Repeat until protector fluid exits
pump outlet. NOTE: This step may require twopeople.
Pressure Washer
1. Drain all water from high pressure hose and wrap it onto
hosewrap.
2. Drain all water from the spray gun and wand by holding
spray gun in a vertical position with nozzle end pointing
down and squeezing trigger. Store in gunholder.
3. Wrap up and secure detergent siphon hose so it is
protected fromdamage.