Use and Care Manual

ManualsBrandsDEWALT ManualsGarage Shelves & Racks48 in. H x 50 in. W x 18 in. D 3-Shelf Steel / Laminate Expandable Industrial Storage Rack Unit in Yellow

Serious injury or death can occur from the rack tipping over. To prevent this, the rack

must be secured to a wall, especially in earthquake -prone areas, or where surfaces are uneven, and where

children and/or pets are present.

Different wall materials require different types of fasteners. Use fasteners suitable for your specific type of

wall. If you are uncertain about what type of fastener to use, then please contact your local hardware store.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-844-377-8451 • www.dewalt.com

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

DXST4500

Titan Industrial Rack 4-Foot (121.92 cm) Tall / 3-Shelf

Étagère industrielle titan 1,22 m (4 pi de hauteur / 3 tablettes

Estantería industrial titan 4 pies (121.92 cm) de altura / 3 estantes

EWA LT

and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an afﬁliate thereof

and are used under license. The yellow/black color scheme is a trademark for D

EWALT

power tools & accessories.

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Parts List

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-844-377-8451

WARNING! Read and understand all instructions. This manual contains

important safety and operating instructions. Please read this manual carefully

before assembling this storage rack and save it for reference.

Technical Specifications

Total Capacity 4,500 lb (2,041 kg)

*when weight is evenly distributed

Capacity per Shelf 1,500 lb (680 kg)

*when weight is evenly distributed

Height 47" (119.4 cm)

Width 49.5" (126 cm)

Depth 18" (45.7 cm)

No. Description Qty.

1 Vertical Beam 2

2 Pre-Bolted Vertical Assembly 2

3 Vertical Assembly Bolt 4

4 Crossbeam 6

5 Shelf Support Strap 9

6 Safety Strap With Weld Nut 6

7 Safety Strap Bolt 12

8 Laminate Deck 3

9 Locking Shelf Pin 16

• Read all instructions thoroughly.

• Remove all components from the box, and lay them on the floor in an orderly fashion.

• Wear eye protection.

• Be cautious of sharp edges.

• Keep this information for further reference.

• If you are not stacking a second rack at this time, then please store the Stacking Plates for potential

future use as they will be needed.

EWALT

WARNING:

Serious or fatal crushing injuries can occur from rack tipping over. To prevent this, the

assembled rack must always be secured to a wall, especially in earthquake-prone environments, where

surfaces are uneven, and where children and/or pets are present.

NOTE: For ease of assembly, two (2) vertical beams feature pre-bolted horizontal and diagonal beams, as

well as pre-attached U-bracket covers.

1. Place one (1) vertical beam and one (1) pre-bolted vertical beam on the floor, parallel to one another

(about 18"/45.7 cm apart). The widest part of the teardrop-shaped hole pattern on each beam should

be facing upward (or away from you). (Fig. 1)

2. There are two versions of the U-bracket covers - an “A” side and a “B” side. Before moving forward,

cover the U-shaped brackets on the vertical beam with the covers by mirroring the covers on the pre-

bolted vertical assembly.

3. Insert the free end of the diagonal beam into the free end of the horizontal beam. Align the holes, and

insert both beams into the U-shaped bracket at the top of the opposing vertical beam. Use the included

hex key or drill bit to thread the vertical assembly bolt through the holes and into the weld nut attached

to the U-shaped bracket. Do not fully tighten the bolt yet. (Fig. 2)

Expandable Upright Frame Instructions (Fig. 1-2)

GENERAL SAFETY

NEVER EXCEED THE FOLLOWING WEIGHT LIMITS

FOR THIS RACK

SPECIFIC SAFETY FOR WALL MOUNT BRACKET

• Keep work area clean and dry.

• Use correct/recommended tools for the job.

• Never leave unattended tools plugged in or running.

• Never force a part into place.

• Wear appropriate safety apparel for the job you are doing.

• Wear safety glasses/goggles.

• Never crawl, sit, stand, or climb on the rack.

• Keep small parts away from children. Never leave a small child unattended while assembling.

• Always use common sense – your personal safety is your responsibility.

• Maximum load for each shelf: Up to 1,500 lb (680 kg) when weight is evenly distributed.

• It is recommended that the heaviest load be placed on the bottom shelf.

Deﬁnitions: Safety Guidelines

The deﬁnitions below describe the level of severity for each signal word. Please

read the manual and pay attention to these symbols.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION:

(Used without word) Indicates a safety related message.

Indicates a practice not related to personal injury which, if not avoided,

may result in property damage.

NOTICE:

No. Description Qty.

10 Carriage Bolt 2

11 10 mm Nut 2

12 10 mm Wrench 1

13 4 mm Hex Key 1

14 4 mm Hex Bit 1

15 Wall Mount Bracket Assembly 1

16 Stacking Plate 2

17 U-Bracket Cover 4

WARNING:

Tools Required for Rack Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included); Rubber

Mallet (not included).

BEFORE YOU BEGIN:

Summary of content (6 pages)

PAGE 1
DXST4500 Titan Industrial Rack 4-Foot (121.92 cm) Tall / 3-Shelf Étagère industrielle titan 1,22 m (4 pi de hauteur / 3 tablettes Estantería industrial titan 4 pies (121.92 cm) de altura / 3 estantes INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES 1-844-377-8451 • www.dewalt.com If you have questions or comments, contact us.
PAGE 2
4. Swing out the bottom horizontal beam, and insert it into the U-shaped bracket at the bottom of the opposing vertical beam. Thread a vertical Aassembly bolt through the holes and into the weld nut. Do not fully tighten the bolt. (Fig. 2) 5. Repeat Steps 1-4 to assemble the second upright frame. Once both are assembled, fully tighten the bolts on all four corners. Be careful not to over-tighten the bolts; there should be no deformation of the U-shaped brackets and/or horizontal beams. FIG. 1 FIG. 2 1.
PAGE 3
Définitions : Règles de sécurité 8 Les définitions ci-dessous décrivent le niveau de danger pour chaque mot indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces symboles. indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la mort ou des blessures graves. indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des blessures légères ou modérées .
PAGE 4
FIG. 3 FIG. 4 FIG. 5 4. Insérez les goupilles de verrouillage de l’étagère dans les trous d’épingle ouverts sur les fixations. Assemblez les pièces restantes de l’étagère supérieure en suivant les instructions précédentes. (Fig. 1-13) FIG. 14 TROU DE GOUPILLE DE VERROUILLAGE FIG. 15 SUPPORT SUPÉRIEUR VERTICAL POUTRE CADRE VERTICAL Instructions pour le support de tablette et la barre de sécurité (Fig.
PAGE 5
LEA TODAS INSTRUCCIONES SEGURIDAD EN GENERAL • Mantenga el área de trabajo limpia y seca. • Utilice las herramientas correctas/recomendadas para el trabajo. • Nunca deje herramientas desatendidas. • Nunca fuerce una pieza para que entre en su lugar. • Use ropa de seguridad. • Utilice gafas/lentes de seguridad. • Nunca se arrastre, se siente, se ponga de pie ni se suba a una estantería. • Mantenga las piezas pequeñas fuera del alcance de los niños.
PAGE 6
Instrucciones para el montaje en la pared (Fig. 9-11) Maximice sus opciones de almacenamiento DEWALT Los anclajes para pared de yeso y los tornillos de anclaje se encuentran incluidos con esta estantería; sin embargo, diferentes materiales de pared requieren diferentes tipos de elementos de fijación. Utilice los herrajes más adecuados para su tipo específico de elementos de fijación. Si no está seguro de qué tipo de elementos de fijación debe usar, póngase en contacto con su ferretería local. 1.