Owner's manual

ManualsBrandsDEWALT ManualsGarage Shelves & Racks20 in. H x 50 in. W x 18 in. D Garage Bench with Wire Grid Storage Shelf

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-844-377-8451 • www.dewalt.com

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

DXSTFB048

Garage Bench

Établi de garage

Banco de taller

EWA LT

and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an afﬁliate thereof

and are used under license. The yellow/black color scheme is a trademark for D

EWALT

power tools & accessories.

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Parts List

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-844-377-8451

WARNING! Read and understand all instructions. This manual contains

important safety and operating instructions. Please read this manual carefully

before assembling this storage rack and save it for reference.

Technical Specifications

Seat Capacity 1,000 lb (454 kg)

*when weight is evenly distributed

Shelf Capacity 1,500 lb (680 kg)

*when weight is evenly distributed

Height 19.75" (50.16 cm)

Width 49.6" (126 cm)

Depth 15" (21.77 cm)

Weight 48 lb (21.77 kg)

No. Description Qty.

1 Cushion Seat 1

2 Pre-Bolted Upright Assembly 2

3 Wire Deck 1

4 Crossbeam 4

5 Bench Top Support Strap (Black) 4

6 Recessed Shelf Support Strap (Yellow) 3

• Read all instructions thoroughly.

• Remove all components from the box, and lay them on the floor in an orderly fashion.

• Wear eye protection.

• Be cautious of sharp edges.

• Keep this information for further reference.

NOTE: It is recommended for one person to hold the pre-assembled upright frames in place while a second

person installs the crossbeams.

NOTE: Keep the bolt heads of the diagonal pieces of the uprights on the outside of the assembly (Fig. 1).

NOTE: The top crossbeams have 4 slots for their associated bench support straps, and the bottom crossbeams

have 3 slots for their associated support straps.

1. There is a set of locking tabs at both ends of every crossbeam. To begin assembly, take a crossbeam with 3

slots and insert the tabs into two of the holes on the lower portion of one upright frame. Engage the locking

tabs into the holes using a downward motion. The locking pin hole should be at the top. Make sure the end of

the crossbeam is flush against the upright frame. (Fig. 1-2)

2. Repeat for the opposite side of the upright frame. Tap the ends of the crossbeam closest to the upright frames

with a rubber mallet until fully seated. The crossbeam and locking tabs should easily slip into place. If they

do not, then recheck the alignment of the teardrop-shaped holes and tabs. Too much force may damage the

interlock between the crossbeam and upright frame.

3. Using the methods listed above, install the other crossbeam with 3 slots to the opposite side of the upright

frames, parallel to the first crossbeam you installed. Make sure both crossbeams are at the same level.

4. Continue by installing the top sets of crossbeams flush to the top of the upright frames (each top crossbeam

has 4 slots and one will have the DEWALT badge on the far right). Make sure the crossbeams are attached at

the same level on both sides. (Fig. 2)

Crossbeam Instructions (Fig. 1-3)

GENERAL SAFETY

NEVER EXCEED THE FOLLOWING WEIGHT LIMITS

FOR THIS BENCH

• Keep work area clean and dry.

• Use correct/recommended tools for the job.

• Never leave unattended tools plugged in or running.

• Never force a part into place.

• Wear appropriate safety apparel for the job you are doing.

• Wear safety glasses/goggles.

• Keep small parts away from children. Never leave a small child unattended while assembling.

• Always use common sense – your personal safety is your responsibility.

• Maximum load for bench seat: Up to 1,000 lb (454 kg) when weight is evenly distributed.

• Maximum load for shelf: Up to 1,500 lb (680 kg) when weight is evenly distributed.

• It is recommended that the heaviest load be placed on the bottom shelf.

Deﬁnitions: Safety Guidelines

The deﬁnitions below describe the level of severity for each signal word. Please

read the manual and pay attention to these symbols.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION:

(Used without word) Indicates a safety related message.

Indicates a practice not related to personal injury which, if not avoided,

may result in property damage.

NOTICE:

No. Description Qty.

7 Safety Strap With Weld Nut 4

8 Safety Strap Bolt 8

9 Locking Shelf Pin 12

10 4 mm Hex Key 1

11 4 mm Hex Bit 1

12 Locking Grid Clip 4

WARNING:

Tools Required for Bench Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included); Rubber Mallet

(not included), Flat-Head Screwdriver (not included).

BEFORE YOU BEGIN:

FIG. 1 FIG. 2 FIG. 3

LOCKING

PIN HOLE

UPRIGHT

FRAME

*KEEP BOLT

HEADS OF

DIAGONAL

PIECE ON

OUTSIDE OF

ASSEMBLY

NOTE: There are two (2) safety straps with weld nuts and three (3) recessed shelf support straps on the bottom

set of crossbeams.

NOTE: There are two (2) safety straps with weld nuts and four (4) bench top support straps on the top set

of crossbeams.

NOTE: Top and bottom crossbeams use different support straps.

1. Starting with the bottom set of crossbeams, place a safety strap with weld nut between the lower ridges of the

crossbeams where two sets of holes have been pre-drilled. Thread a safety strap bolt up through the bottom

of the pre-drilled holes and through the weld nuts, and fully tighten with the included hex key or drill bit. Repeat

for the second strap on this set of crossbeams, and continue for the last 3 straps. (Fig. 5)

Safety Strap and Support Strap Instructions (Fig. 4-7)

Summary of content (4 pages)

PAGE 1
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. No. Description 1 Qty. Cushion Seat 1 No. Description 7 Qty.
PAGE 2
. On the bottom of the bench, place a recessed shelf support strap (yellow) perpendicular to the bottom crossbeams, and insert each end into the channel on each ridge of the crossbeam. Repeat for the remaining 2 (yellow) straps. (Fig. 6) Définitions : Règles de sécurité Les définitions ci-dessous décrivent le niveau de danger pour chaque mot indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces symboles. 3.
PAGE 3
Outils requis pour l’assemblage de l’établi : Clé hexagonale de 4 mm (incluse) OU mèche hexagonale de 4 mm (incluse), maillet en caoutchouc (non inclus), tournevis à tête plate (non inclus). FIG. 8 FIG. 9 FIG. 10 AGRAFE DE VERROUILLAGE DE GRILLE LIRE TOUTES LES CONSIGNES VERROUILLAGE DE LA GOUPILLE DE L’ÉTAGÈRE DANS UN TROU DE GOUPILLE DE VERROUILLAGE SUR UNE TRAVERSE AVANT DE COMMENCER : • Veuillez lire attentivement toutes les instructions.
PAGE 4
ADVERTENCIA: NO EXCEDA LOS SIGUIENTES LÍMITES DE PESO AL USAR ESTA BANCO Instrucciones para las barras de seguridad y las barras de apoyo (Fig. 4-7) • Capacidad de carga máxima del banco: hasta 1000 lb (454 kg) cuando el peso se encuentra distribuido de manera uniforme. NOTA: Hay dos (2) barras de seguridad con tuercas soldadas y cuatro (4) barras de apoyo superiores para el banco en el conjunto superior de las vigas transversales.