Technical information

6 GB/IE
Safety advice
The following advice is intended for your safety and
satisfaction during operation of the device. Please
note that non-observation of this safety advice can
lead to considerable danger.
Explanation of the symbols and terms used:
c Danger! Non-observance of this instruction or
advice could endanger life and health.
m Attention! Non-observance of this instruction or
advice will endanger property.
Tip! Observance of this instruction or advice will
achieve best performance.
c Danger!
• Do not leave small children unattended with the
device, packaging material or small parts! Other-
wise there is a risk to life from suffocation!
• When you drill holes or install the fastenings
make sure that you do not damage any cables or
pipes carrying gas, electricity, water or telecom-
munications! Otherwise there is a risk to life and
limb!
• Handle the electricity supply feed cable carefully!
Place the cable in such a position that it cannot
be damaged or become a trip hazard. Fasten the
cable in place with an adequate number of cable
clips. Do not pull the cable over sharp edges or
allow it to become squashed or clamped in other
ways. Otherwise there is a risk to life and limb!
• If you use the device for monitoring babies or
small children ensure that the camera and cable
are out of reach of children. Otherwise there is a
risk to life and limb!
• Do not allow the mains adapter to come into con-
tact with moisture! Otherwise there is a danger to
life!
m Attention!
• Operate the camera with 9 V DC only!
Check before connecting the mains adapter to
the mains that the electricity supply circuit is
230 V ~ AC, 50 Hz and is fitted with a max. 16 amp
fuse or trip.
• Protect the camera and cable from strong
magnetic or electric fields!
• Do not place the device near fire, heat, or subject
it to prolonged high temperatures!
• Protect the device from violent mechanical loads
and vibrations!
• Use the device only with the supplied original
parts or original accessories!
• Before assembling and bringing the device into
use check the supplied items for damage and
completeness!
• If the device is damaged (e.g. transport damage) do
not connect it. If in doubt ask your customer service
centre. Repairs and interference with the device
may only be carried out by trained specialists.
• Use a dry or slightly moist cloth for cleaning the
device. Never immerse the device in water.
Safety advice
Planning where you install the device
Before you install the camera you must first plan
what to do at the installation site.
Example installation see Fig. B
Check that the camera works satisfactorily at the
installation site before you install it.
Tip! Observe the following points:
o The camera should be attached in such a way
that as little direct light or direct sunlight as pos-
sible strikes the lens. When considering this,
remember that the position of the sun does not
remain constant. The camera image is best che-
cked before it is installed. To do this set the ca-
mera operating and hold it in the planned positi-
on. If necessary alter the position of the camera
until you obtain your desired picture coverage.
o The camera has an infrared light for the adjacent
area for better facial recognition. Additional
lighting in the area at night will improve the
image quality from the camera.
o If you wish to install the camera outside a buil-
ding please remember that it must be possible to
provide a cable feed hole to the installation site.
The installation site should if possible be shel-
tered from rainfall.
o Avoid wherever possible placing the connection
cable directly alongside electrical cables other-
wise this could adversely affect picture and
sound quality.
Power supply
o Connect the scart-plug
U
to the scart socket of
your television set.
o Insert the cable plug
R
firmly into the hole in the
ball joint
E
of the camera
Q
.
Tip! Insert the cable plug so firmly into the ball
joint that you hear three clicks. Only when you do
this is the cable properly connected.
o Connect the mains cable plug
O
to the socket
Y
.
o Connect the mains adapter
I
to a mains socket.
Checking that the camera functions properly
o Switch on your television.
o Set your television to the AV channel correspon-
ding to the connected scart socket.
o Now check picture and sound.
o Lay out the cable on a temporary basis to the
proposed installation site.
o Check the actual picture displayed.
o Adjust the camera direction if necessary.
o Switch the television off again.
o Pull out all the connections.
o Continue with the installation.
Assembly and installation
Cable feed hole (for outside
installation only)
o Select a suitable position for the cable feed hole
p
(preferably directly below the bracket
{
KOE27_T02_Content.indd 6 23.10.2006 9:56:00 Uhr