Quick Installation Guide

ManualsBrandsDexatek Technology ManualsElectronicsEve Light Strip

LED Strip QIG Artwork (Outsite)

Color：Black

Size：257 x 182 (mm)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following

measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

To assure continued compliance, any changes or modications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to

computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should

be installed and operated with a minimum distance of

20 centimeters between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and

must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operation.

Includes

Package contents ( more accessories under the second layer)

Power adapter. Control box

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備

之干擾。功率或變更原設計之特性及功能。

繁體中文

English

CE declaration of conformity

• Directive 2014/53/EU • EMC Directive 2014/30/EU

• Low Voltage Directive 2014/35/EU • RoHS Directive 2011/65/EU

Proper use

The unit is the central base station that can be used to monitor and control up to 16 Smart Home components. You can

thus check your settings and keep an eye on your components at all times worldwide via the app.

website: www.en.sigmacasa.com

SA-7199

連接變壓器與控制器

請將變壓器接頭接上控制器。

連接控制器與燈帶

請將燈帶接頭接上控制器，並

將變壓器插頭接上電源，此時

燈帶會亮起。

執行應用程式

開啟 iPhone 家庭應用程式。

家庭

加入配件

點選「加入配件」，掃描控制

器上 HomeKit 代碼。

請將設定代碼收在安全的地方，除了

您，沒有其他人擁有副本。

開始使用

配對完成！立即使用應用程式

或 Siri 享受 Apple 家庭帶給

您的便利生活。

配對完成

設定顏色

亮度 80%

開始使用

您也透過 Apple Home App

，進行亮度或顏色的調整。

Reset

重新設定

使用迴紋針，輕按控制器

旁 Reset 按鈕十秒，在燈

帶閃爍並變色後，即可重

新設定您的 LED Strip。

請於連接電源狀態下操作

Connect transformer to controller

Please connect the transformer

connector to the controller.

Connect the controller

and the light belt

Please connect the lamp belt connector

to the controller, and Connect the plug

of the transformer to the power supply.

The light strip will light up.

Run the application

Open the iPhone home app.

家庭

加入配件

Add accessories

Click "Add accessories", scan control

HomeKit code on the device.

Please store the setting code in a safe

place. No one but you has a copy.

Start using

Pairing is complete! Use the app or Siri

now to enjoy the convenience of life

brought to you by the Apple family.

配對完成

設定顏色

亮度 80%

Start using

You can also adjust the brightness

or color through the Apple Home

App.

Reset

Using a paper clip, lightly press

the Reset button next to the

controller for ten seconds.

After the light strip flashes and

changes color, you can reset

your LED Strip.

Please operate with power

connected

 