RM21400 Chassis Installation Reference Guide 1 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
Copyright This document is copyrighted, 2002, by Chenbro Micom Co., Ltd. and all rights are reserved. Chenbro Micom Co., Ltd. reserves the right to make improvements to the products described in this document at any time without prior notice. Specifications are thus subject to change without notice. No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Chenbro Micom Co., Ltd.
Table of Contents Chapter 1 General Information.........................................................................4 1.1 Specification........................................................................................4 1.2 Features..............................................................................................4 Chapter 2 SCSI Backplane Installation ............................................................6 2.1 Remove the top cover...................................................
Chapter 1 General Information 1.1 Specification Model Name RM214 Standard EIA-RS310D M/B Form Factor ATX/Extended ATX CPU Support DP Xeon/AMD Athlon Dimension (D x W x H) 610mm x 430mm x 88.1mm 24" x 16.9" x 3.
- Compliance with Dual Intel Xeon or Dual AMD MP Server boards Validated Thermal Solution Optional 4cm fan on rear panel for pulling out heated air efficiently. System Monitoring Buzzer alarm for Fan failure and overheat warning Support Alarm reset Application Strength Designed for high density front end server Ideal for NAS and RAID application and also for general purpose server 5 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C.
Chapter 2 SCSI Backplane Installation 2.1 Remove the top cover 1 2 Remove three screws on top cover. Push top cover backward and life off the top cover. 3 2 1 2.2 Remove the fan bracket 1 2 3 Remove two screws on left & right side of fan bracket. Lift off the fan bracket from chassis. Set the fan bracket and screws aside for reattachment later. 6 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
2.3 Remove the HDD drawer 1 Push the blue door lock to right-hand side; the handle will be release automatically. 2 1 2 Use the handle to pull HDD drawer out a little bit. 7 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
2 1 3 Repeat the same operation for the other 5 drawers. 4 Rear view of HDD trays. 2.4 Install the SCSI backplane assembly 1. Insert the SCSI backplane assembly into chassis. 8 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
2. Check whether the SCSI bracket assembly is installed properly. 9 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
3. Fasten the screws to fix the SCSI backplane assembly. 4. Push the HDD drawers back to drive trays. 10 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
2.5 Connect LED and switch wires There is one 2 x 9 pin connector on left-bottom side on SC SI backplane. This connector provides several LED and switch connections for devices. The detail pin definition is listed below. Pin 1 Pin 3 Pin 5 Pin 7 Pin 9 Pin 11 Pin 13 Pin 15 Pin 17 1. Pin 1 Pin 3 Pin 5 Pin 7 Pin 9 Pin 11 Pin 13 Pin 15 Pin 17 2. 3.
4. Pin 1 Pin 3 Pin 5 Pin 7 Pin 9 Pin 11 Pin 13 Pin 15 Pin 17 5. 6. Check the pin number of “Fail LED” connector. Device 1 Power LED Device 1 Access LED + Device 2 Power LED Device 2 Access LED + Device 3 Power LED Device 3 Access LED + Fail LED N/A Reset - Pin 2 Pin 4 Pin 6 Pin 8 Pin 10 Pin 12 Pin 14 Pin 16 Pin 18 Device 1 Power LED + Device 1 Access LED Device 2 Power LED + Device 2 Access LED Device 3 Power LED + Device 3 Access LED Fail LED + N/A Reset + Plug “LED” connector into pin 13 & 14.
7. Pin 1 Pin 3 Pin 5 Pin 7 Pin 9 Pin 11 Pin 13 Pin 15 Pin 17 8. Check the pin numbers of HDD LED connectors. Device 1 Power LED Device 1 Access LED + Device 2 Power LED Device 2 Access LED + Device 3 Power LED Device 3 Access LED + Fail LED N/A Reset - Pin 2 Pin 4 Pin 6 Pin 8 Pin 10 Pin 12 Pin 14 Pin 16 Pin 18 Device 1 Power LED + Device 1 Access LED Device 2 Power LED + Device 2 Access LED Device 3 Power LED + Device 3 Access LED Fail LED + N/A Reset + Plug HDD LED cables into connectors properly.
9. Plug the LED with red wire to the lowest LED len. 10. Plug the green LED with green wire to the second lowest LED len. 14 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
11. Repeat step 9 & 10 till all LED are installed properly. 12. Use the same way to install the LED on another SCSI backplane. Till now, the installation of LED is completed. 13. Plug the power connectors to SCSI backplane. 15 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
14. Plug the power connectors for another SCSI backplane. 15. Attach the SCSI cable to the unused SCSI connector. 2.6 Reattach the fan bracket and top cover 1. Plug two of the fan power connectors on fan bracket onto SCSI backplane. The left fan connector should be connected to M/B. 16 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
2. Reattach the fan bracket and arrange the cables properly. 3. 4. Fasten the screws that are detached in section 2.2. Put the top cover back and fasten the screws. Please check section 2.1 for detail locations of screws. The installation of SCSI backplane is finished now. 1 2 17 Chenbro Micom CO., LTD. 15Fl., No. 150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan, R.O.C. Tel: +886-2-8226-5500 www.chenbro.com.
