Instruction manual

ManualsBrandsDexter Laundry ManualsDryerDRC55 Series

INSTRUCTION MANUAL

for

DRC55 Series Dryers (25Kg Capacity)

The dryer must not be stored or installed where it will be exposed to water and/or weather and is

suitable for use in room temperatures between 5C and 45C.

WARNING: For your safety the information in this manual must be followed to minimize

the risk of fire or explosion or to prevent property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

- WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in your building.

- Clear the room, building or area of all occupants.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

You, the purchaser, must post in a prominent location instructions to be followed in the

event the user smells gas. Consult your local gas supplier for procedure to be followed if

the odor of gas is present.

Post the following “For Your Safety” caution in a prominent location:

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or

any other appliance or machine.

It is important that you read this Manual and retain it for future reference.

For service or replacement parts, contact the Dexter Distributor in your area or the manufacturer.

The Dexter Company

2211 W. Grimes

Fairfield, Iowa 52556, USA

8514-027-005

Summary of content (12 pages)

PAGE 1
INSTRUCTION MANUAL for DRC55 Series Dryers (25Kg Capacity) The dryer must not be stored or installed where it will be exposed to water and/or weather and is suitable for use in room temperatures between 5C and 45C. WARNING: For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
PAGE 2
TABLE OF CONTENTS Page No. Dryer Dimensions (Figure 1).............................................................................................. 3 Uncrating .......................................................................................................................... 4 Field Assembly.................................................................................................................. 4 Dryer Installation.............................................................................
PAGE 3
FIGURE 1 - DRYER DIMENSIONS -3-
PAGE 4
INSTALLATION AND OPERATING INSTRUCTIONS Note: Before installation, check that the local distribution conditions, nature of gas and pressure, and the adjustment of the appliance are compatible. UNCRATING 1. Remove cardboard container and innerpack. 2. Complete the uncrating as described in the procedure listed on the instruction sheet taped to the loading door glass. FIELD ASSEMBLY For secure packaging, the dryer is shipped with the tee, one part of the heat reclaimer, inside the lower service door.
PAGE 5
III. Back IV. Front V. Top VI. Floor 18 in. (450 mm) clearance is necessary behind the belt guard to allow servicing and maintenance. 48 in. (1200 mm) to allow use of dryer. Refer to figure labeled “Vertical Clearance Dimensions”. AB. 0 clearance at the top, 1 in. (25 mm) back from the front. However 1/4 in. (6 mm) clearance is required to allow opening the upper service door. CD. A 4 in. (100 mm) clearance is required at the top between 1 in. (25 mm) and 4 in. (100 mm) from front. E.
PAGE 6
MAKE-UP AIR. Adequate make-up air (910 CFM) (26 m3/Min.) must be supplied to replace air exhausted by dryers on all types of installations. Provide a minimum of 1.25 sq. ft. (.12 m2) make-up air opening to the outside of each dryer. This is a net requirement of effective area. Screens, grills or louvers which will restrict the flow of air must be considered. Consult the supplier to determine the free area equivalent for the grill being used.
PAGE 7
This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space. Consult instructions before installation of this appliance. GAS SYSTEM INFORMATION HEAT INPUT 38.1 kW GROSS GAS FLOW RATE 3.5 m3 PER HOUR BURNER PRESSURE 8.7 mbar G20 / 12.2 mbar G25 INJECTOR SIZE 3.9 mm COUNTRY CATEGORY ORIFICE (mm) 2ND / 3RD FAMILY REGULATOR. SETTING mBAR 2ND / 3RD FAMILY GB IE IT CH ES II 2H3+ 3.9 / 2.4 8.7 / ANNULLED FR II Er3+(29/37) 3.9 / 2.4 8.
PAGE 8
CONVERSION TO LP GAS (G30): Conversion of this appliance to LP gas requires a kit supplied by the Dexter Company. Please contact your local Dexter distributor to purchase the proper conversion kit. Be sure to keep the instructions provided with the kit along with these instructions for reference. PRESSURE REGULATOR ADJUSTMENT Adjustments should be made by qualified personnel only. 1.
PAGE 9
If the exhaust pipe passes through a wall, a metal sleeve of slightly larger diameter should be set in the wall and the exhaust pipe passed through this sleeve. This practice is required by some local codes and is recommended in all cases to protect the wall. This type of installation should have a means provided to prevent rain and high winds from entering the exhaust when the dryer is not in use. A hood with a hinged damper can be used for this purpose.
PAGE 10
dryer ducts. The main duct can be rectangular or round, provided adequate air flow is maintained. For each individual dryer, the total exhausting (main discharge duct plus duct outlet from the dryer) should not exceed the equivalent of 20 ft. (6 m) and two elbows. The diameter of the main discharge duct at the last dryer must be maintained to exhaust end. NOTE: A small diameter duct will restrict air flow; a large diameter duct will reduce air velocity - both contributing to lint build up.
PAGE 11
DESCRIPTION OF CONTROLS Credit for coins deposited, dryer time and temperature are controlled by an electronic control. The large digital display shows vend price of an idle dryer, time purchased after coins are deposited, temperature and program information. The three red indicator lights show the drying temperature selected. This selection may be made anytime. The drying temperature will be displayed when the start switch and the switch for selected temperature are pressed at the same time.
PAGE 12
CHANGING PROGRAM DATA Put dryer in PROGRAM mode (see “Programming Instructions”). The dryer remains in the PROGRAM mode until one of these actions occur: • • • • The switch is actuated again. The fifteenth step is completed, and the START switch is pushed following the fifteenth step. Programming is stopped for about a minute. The loading door is closed. Observe the displayed value in each step. If no change is required, press START to advance to the next program step.