P/N 8514-031-001A 05/08 WCND HCSMODEL lb CAPACITY OPL (Computer) WASHER THE DEXTER COMPANY OWNER'S BOOKLET INSTALLATION & OPERATION INSTRUCTIONS TABLE OF CONTENTS Safety Warnings Maintenance Hints Installation Instructions Foundation Requirements Mounting Plumbing Drain Electrical Fusing Requirements Electrical Connections Chemical Injection Chemical Injection Hoses Final Checkout Operating Controls Operating Instructions End Of Cycle Safety Door Lock Motor Drive Indications Computer Control Cyc
Figure 7 Figure 8 Figure 9 - Push-button Control Switches Recommended Detergent Quantity Bath Setting Limits 9 10 11
Please read this information and retain for reference. WARNING - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE OPERATION. TO AVOID INJURY OR ELECTRICAL SHOCK, DO NOT PERFORM ANY SERVICING UNLESS QUALIFIED TO DO SO. IT IS THE RESPONSIBILITY OF THE OWNER TO CHECK THIS EQUIPMENT ON A FREQUENT BASIS TO ASSURE ITS SAFE OPERATION. A machine should not be allowed to operate if any of the following occur: ! ! ! ! Excessively high water level.
INSTALLATION INSTRUCTIONS All washers must be installed in accordance with all local, state and national building, electrical, plumbing and other codes in effect. WARNING - THESE INSTALLATION AND SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID INJURY AND ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING UNLESS QUALIFIED. FOUNDATION REQUIREMENTS This machine is designed for use on or over bare concrete floor - not to be used above combustible flooring.
ELECTRICAL WARNING SHUT OFF POWER AND WATER BEFORE OPENING ANY SERVICE PANELS. Dexter T600 washing machines are intended to be permanently installed appliances. The machine should be connected to an individual branch circuit not shared by lighting or other equipment. The connection should be sheathed in liquid-tight flexible conduit, or equivalent, with conductors of the proper size and insulation. No power cord is provided.
CHEMICAL INJECTION Dexter T600 washing machines are intended to be permanently installed appliances. The machine is intended to have a chemical injection system operating with it. There are convenient electrical connection points for the injection pumps shown in Figure 3. Up to four (4) independent pumps can be controlled through the signals A, B, C and D. The injection pump signals are 115 VAC. The COM shown in Figure 3 is the common or return for these injection signals.
FIGURE 5 - THOROUGHBRED 600 SPECIFICATIONS MODEL WCN40AFH CAPACITY 6 CUBIC FT. (UP TO 40#) CYLINDER DIM. 25" DIA. x 21 1/8" DEPTH GROSS WEIGHT NET WEIGHT 656 POUNDS 622 POUNDS ELECTRICAL 208-240 VAC, 60 HZ, 1 PH OR 3 PH EXTRACTION FORCE 100 g=s WASH SPEED SPIN SPEED 43 R.P.M. 531 R.P.M. DRIVE SYSTEM SOFT START REVERSING AC MOTOR DRIVE WATER INLET 2 SOLENOID OPERATED VALVES FLOW RATE, 9 GAL./MIN.
OPERATING CONTROLS There are four (4) switches that control the washer operation. shown below followed by an explanation of each switch. Each switch is Figure 7 - Push-button Control Switches STOP (RED) Push-button - Depress momentarily. Stops the washer during the cycle. All washer cycle information is retained, the door remains locked and the water remains in the tub. STOP (RED) Push-button - Depress and hold for 3 seconds or longer. Stops the washer and clears the cycle.
OPERATING INSTRUCTIONS 1. Ensure that power is on to the washer. 2. Ensure that the ADVANCE/RUN/PROGRAM keylock is in the RUN position. 3. Load the clothes loosely in the cylinder and latch the door securely. Be sure clothing does not get caught between the door gasket and tub front when closing the door. NOTE: To begin closing the door, the handle must be in the horizontal position.
the STOP button for a minimum of three seconds.
END OF CYCLE At the end of the cycle the machine stops, the END CYCLE LED lights, the alarm sounds and the loading door unlocks allowing unloading of the machine. SAFETY DOOR LOCK This machine is equipped with a Safety Door Lock which prevents opening the door if power is interrupted, until it is safe to do so. If power failure occurs it will be necessary to wait 2 to 3 minutes before the door can be opened.
Source Spin Time through 6 relating to an injection source. See Recommended Injection Table. 0 to 10 minutes (1 min. increments) 14 The spin time settings are 0 min. to 10 min. in 1 min. increments. If the setting is 0, there is no spin for the bath. Final Rinse/Extract minimum setting is 1 min.
PROGRAMMING INSTRUCTIONS - EDITING EXISTING CYCLE There are 29 preset wash cycles programmed into the washer at the factory. Although these cycles are common industry cycles, there may be a need to tailor the cycle to meet an exact application. This can easily be done with the following instructions. Note: It is recommended when changes are made to one or more of the preset programs that the cycle number and the changes be documented for later reference.
entered.) The Water Level LED lights and the Water Temperature LED are out. The water level for this segment is displayed. If no change is required, then continue to the next instruction. If a change is required, then use the SCROLL UP/SCROLL DOWN buttons to change the water level. {"HI" is a high water level and "LO" is a low water level} When the desired water level is selected, continue to the next instruction. When the No Water bath is selected, the water level has no effect.
washer. Although these cycles are common industry cycles, there may be a need to add a cycle to meet an exact application. This can easily be done with the following instructions. Note: It is recommended when cycle(s) are made the cycle number and the cycle steps be documented for later reference. Blank cycle sheets have been provided at the end of the Preset Cycle Information section. The instructions for entering a new cycle are the same as the editing a cycle instructions.
For each number in the test, the function will be active when the START button is pushed and will be inactive when the START button is released. Use the SCROLL UP to move from one function to the next. ! Step 1 - Lock the door. ! Step 2 - Turn on thermoactuator #1 (lock). ! Step 3 - Turn on thermoactuator #2 (unlock). ! Step 4 - Close the drain valve. ! Step 5 - Turn on the cold water to the tub. The pressure switch low level setting can be tested at this point.
The I/O interface outputs labeled Reverse, Speed1 and Speed2 will be active (the three RED LED=s will light). DO NOT USE STEP 14 IF YOU HAVE CUSTOMIZED CYCLES PROGRAMMED AS THIS WILL SET THE CYCLES BACK TO THE FACTORY PRESETS. ! Step 14 - Preset Cycles. Push START and hold, then push SCROLL UP. will reset the DEXTER preset cycles back to the factory settings. This At cycle complete, switch the Advance/Run/Program switch to the Run position and the unit is ready to select a run cycle.
cycle will continue normally. Notes: • The cycle cannot be advanced during the “open drain” step of the bathes. • The cycle cannot be advanced when the hot and cold water valves to the tub are on after advancing during or after a chemical injection. • The cycle cannot be advanced again while the hot and cold water valves to the tub are on after advancing when the water temperature was 65 to 90. • The Rapid Advance mode may only be entered after a cycle is started.
OPL 40 POUND WASHER COMPUTER CONTROLLED PRESET CYCLE INFORMATION APPLICATION Shirt/Laundry CYCLE # 1 2 DESCRIPTION Shirts (No Starch) Shirts (Starch) Hotel/Motel 3 4 5 6 7 8 9 10 11 12 White Sheets White Pillowcases White Towels, Bath Mats, Wash Cloths Colored Sheets & Towels Delicate Wash Housekeeping Rags & Mops Housekeeping Uniforms Stain Treatment Reclaim Part 1 Part 2 Health Care 13 14 15 16 17 Sheets & Pillowcases Towels Diapers & Pads Personals Delicate Food & Beverage 18 19 20 21 22 23 24
CYCLE 1 Shirt/Laundry Shirts (No Starch) Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level 12 2 2 2 HH CH CH CH LO HI HI HI 4 CH LO Inject Source Spin Time Detergent/Bleach1 3 Total Time: 25 minutes excluding the tub fill time. Notes: 1. Use only oxygen bleach in shirt laundries. DO NOT USE CHLORINE BLEACH.
CYCLE 3 Hotel/Motel White Sheets Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 7 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Soft Spin Time 1 4 Total Time: 27 minutes excluding the tub fill time.
CYCLE 5 Hotel/Motel White Towels Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 7 1 7 2 2 HH HH HH CH CH LO HI LO HI HI Detergent 4 CH LO Sour/Soft Spin Time Bleach 1 5 Total Time: 29 minutes excluding the tub fill time.
CYCLE 7 Hotel/Motel Delicate Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 8 2 2 2 CH HH CH CH HI HI HI HI Detergent/Bleach 4 CH LO Sour/Soft Spin Time 4 Total Time: 22 minutes excluding the tub fill time.
CYCLE 9 Hotel/Motel Uniforms Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 7 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Soft Spin Time 1 4 Total Time: 29 minutes excluding the tub fill time.
CYCLE 11 Hotel/Motel Reclaim (Part 1) Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 20 3 HH HH LO HI Manual 3 HH HI Spin Time 1 Total Time: 27 minutes excluding the tub fill time.
CYCLE 13 Health Care Sheets & Pillowcases Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 3 2 7 7 2 2 CH CH HH HH CH CH HI HI LO LO HI HI Detergent Bleach 4 CH LO Sour/Soft Spin Time 1 4 Total Time: 32 minutes excluding the tub fill time.
CYCLE 15 Health Care Diapers Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time 3 2 2 7 2 7 2 2 4 Water Temp Water Level CH CH CH HH HH HH CH CH CH HI HI HI LO HI LO HI HI LO Inject Source Spin Time Detergent Bleach 1 Sour/Soft 4 Total Time: 36 minutes excluding the tub fill time.
CYCLE 17 Health Care Delicate Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level 2 CH HI 7 2 2 2 CH CH CH CH HI HI HI HI 4 CH HI Inject Source Spin Time Detergent/Bleach Sour/Soft 3 Total Time: 22 minutes excluding the tub fill time.
CYCLE 19 Food & Beverage Colored Cotton Linen Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 10 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Starch Spin Time 1 4 Total Time: 32 minutes excluding the tub fill time.
CYCLE 21 Food & Beverage Colored 100 % Polyester Linen Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 10 7 2 2 HH HH CH CH LO LO HI HI Detergent Bleach 4 CH LO Sour/Starch Spin Time 1 4 Total Time: 32 minutes excluding the tub fill time.
CYCLE 23 Food & Beverage Kitchen Rags Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 5 2 8 2 7 2 HH HH HH HH HH CH LO HI LO HI LO HI Detergent 2 CH HI Spin Time Detergent 1 Bleach 1 5 Total Time: 35 minutes excluding the tub fill time.
CYCLE 25 Food & Beverage White/Colored 100 % Polyester Linen Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 2 CH HI 10 1 2 2 2 HH HH HH CH CH LO HI LO HI HI Detergent/Bleach 4 CH LO Sour/Starch Spin Time 4 Total Time: 27 minutes excluding the tub fill time.
CYCLE 27 Food & Beverage Kitchen Rags Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level Inject Source 5 2 10 1 2 2 HH HH HH HH HH CH LO HI LO HI HI HI Detergent 2 CH HI Spin Time Detergent/Bleach 1 5 Total Time: 30 minutes excluding the tub fill time.
CYCLE 29 Other Oxygen Bleach Terry (No Iron) Segment Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Cycle Time Water Temp Water Level 3 2 10 2 2 2 CH CH HH HH CH CH HI HI LO HI HI HI 4 CH LO Inject Source Spin Time Detergent/Bleach 1 Sour/Soft 5 Total Time: 31 minutes excluding the tub fill time.
CYCLE Segment Cycle Time Water Temp Water Level Inject Source Spin Time Inject Source Spin Time Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Total Time: Notes: CYCLE Segment Cycle Time Water Temp Water Level Flush Prewash Wash Rinse 1 Rinse 2 Rinse 3 Rinse 4 Rinse 5 Final Total Time: Notes: 37
