Luckylight 1.90mm Height 1411 Package Top View Full Color Chip LEDs Technical Data Sheet Part No.: LL-R3528RGBC-008-B Spec No.: R3528RGB Rev No.: V.2 Date: Jan./26/2006 Approved: ZHOU Checked: Wu Drawn: Shu Lucky Light Electronics Co., Ltd. Page: 1 OF 12 http://www.luckylightled.
Luckylight Features: ◇ P-LCC-4 package. ◇ White package. ◇ Optical indicator. ◇ Colorless clear window. ◇ Black face. ◇ Ideal for backlight and light pipe application. ◇ Inter reflector. ◇ Low current (2mA) operation. ◇ Wide viewing angle. ◇ Suitable for automatic placement equipment. ◇ Suitable for vapor-phase reflow, Infrared reflow and wave solder processes. ◇ Available on tape and reel (8mm Tape). ◇ The product itself will remain within RoHS compliant Version.
Luckylight Package Dimension: 1 (COM) 3 4 3.2 [0.126] 0.8 [0.032]± 0.3 4 3 0.75 [0.030]± 0.3 0.9 0.8 0.9 2 2.8 [0.110] Recommended Soldering Pad Dimensions 0.8 [0.032] 1 Polarity 0.2 [0.008] 0.2 [0.008] 0.8 [0.032] 0.15 [0.006] 3.5 [0.138]± 0.2 0.8 [0.032] 2 Polarity Mark 1.9 [0.075]± 0.2 2 1 COMMON ANODE 2 CATHODE RED 3 CATHODE GREEN 4 CATHODE BLUE 0.8 [0.032] 1 2.8 [0.110]± 0.2 3 0.75 [0.030] 4 1.9 [0.075]± 0.2 0.7 [0.028] 2.2 [0.087]± 0.2 3.2 [0.126]± 0.2 φ2.4 [.094] 1.
Luckylight Absolute Maximum Ratings at Ta=25℃ Parameters Power Dissipation Symbol PD Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Continuous Forward Current Reverse Voltage IFP IF Max.
Luckylight Electrical Optical Characteristics at Ta=25℃ Parameters Luminous Intensity Viewing Angle Peak Emission Wavelength Dominant Wavelength Spectral Line Half-Width Forward Voltage Emitting Color Min. Typ. Max.
Luckylight Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Hyper Red: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 800 1.6 1.8 2.0 2.2 2.4 2.
Luckylight Pure Green: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 2.8 3.0 3.2 3.4 3.6 3.8 4.
Luckylight Blue: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 2.8 3.0 3.2 3.4 3.6 3.8 4.
Luckylight Reliability Test Items And Conditions: The reliability of products shall be satisfied with items listed below: Confidence level: 90%. LTPD: 10%. 1) Test Items and Results: No. Test Item Test Hours/Cycles Test Conditions Sample Size Ac/Re 1 Resistance to Soldering Heat 6 Min Tsld=260±5℃, Min.
Luckylight Reel Dimensions: Carrier Tape Dimensions: Loaded quantity 1500 or 2000 PCS per reel. Spec No.: R3528RGB Rev No.: V.2 Date: Jan./26/2006 Approved: ZHOU Checked: Wu Drawn: Shu Lucky Light Electronics Co., Ltd. Page: 10 OF 12 http://www.luckylightled.
Luckylight Please read the following notes before using the product: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.
Luckylight 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 6. Caution in ESD Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.
