Light Chaser Beginner Soldering Kit
Coin Cell Battery designed to help kids or electronic, enthusiasts, and novices learn Product Introduction about electronic basics like soldering and simple circuits. Mr. NEON is designed to look like a three-leg monster whose eyes or tentacles M Vibration Motor Photodiode glow and dim depending on surrounding light. The stronger the light is, the faster Mr. NEON moves.
These working principles are illustrated in the diagram below. 2. Strobe A, located in the thick pipe, is controlled by the water flow in the thin pipe; the thin pipe is controlled by strobe B. Pool 3. If there is no water flow in the thin pipe, then the strobe located in the thick pipe will close. The greater the water flow in the thin pipe, the wider strobe A opens up. Since strobe A controls water flow through the thick pipe, water flow will increase when strobe A opens.
Step1 How to Solder Bend the legs downward and insert them into the board. Step3 Pull the soldering wire away first, then the soldering iron. Step2 Flip the board over. Place the soldering iron’s ”sweet spot ” (shown in diagram) and make sure it touches both the leg and the metal ring. Hold for 1 to 2 seconds. Step4 Your solder joints should look like this: a tiny volcano.
Clip off all excess wire so that only the tiny solder joints remain. 20K 20K 20K 20K 1. Solder the resistors After soldering, cut off the remaining length of the wire. Step6 Resistance soldering completed. WARNING: Please wear safety goggles. This kit requires soldering and clipping leads. 20K Ohm Resistor Used for limiting current or dividing voltage, a resistor is a common component within circuits.
2. Solder the switch 4-Soldering Light Chaser Kit V1 on After soldering, cut off the remaining length of the wire. 3. Solder the transistors 4-Soldering Light Chaser Kit V1 After soldering, cut off the remaining length of the wire. off Switch The switch is for power ON and OFF. Transistor The transistor is a powerful component. Notice the silkscreen (white print on the board) resembles a half circle. Make sure that place the transistors in the holes on the basis of the silkscreen.
4. Solder the photodiodes 4-Soldering Light Chaser Kit V1 After soldering, cut off the remaining length of the wire. Photodiode(S8050) The photodiode is a component that changes a light signal into a current or voltage signal. It is highly sensitive to light intensity, and can be used to change a circuit’s current. Insert the photodiodes into the front of the board. Each photodiode has a short leg and a long leg. The long leg goes into the hole labeled with a long line.
4-Soldering Light Chaser Kit V1 + 5. Solder the Battery Clip + 4-Soldering Light Chaser Kit V1 6. Solder the vibration motors After soldering, cut off the remaining length of the wire. Battery Clip The battery clip is for holding the coin cell battery. Set the battery clip on the white footprint of the upper side of the board. Solder the two clip legs from the opposite side while keeping the part flat. Vibration Motor The vibration motor provides the power source that enables Mr.
Making the Base Step1 Take out the plastic paper and the sticker with a printed triangle. Mr. Neon should at this point look like the above picture.
Step2 Step3 Unpeel the triangle sticker and place it atop the plastic paper. Cut the plastic paper with a scissor along the edge of the triangle.
Step4 Step5 Trim the sharp corners of the triangle. Bend three small triangles into 90 degrees along dotted lines.
Step6 Step8 Place the adhesive against the body as shown. Stick the two vibration motors against Mr. NEON’s legs. Step7 Step9 Put the head on the body. Place the plastic tubing over the photodiodes; this prevents electric interference with the exposed probe.
Shipping List Done You've assembled Mr. Neon! You can add stickers to Mr. Neon to give him appearance and flair that make him stand out from the rest. A step-by-step video walkthrough showing the assembly of Mr. Neon is available online — to view it, please go to the DFRobot Mr. Neon product page.
dfrobot dfrobot dfrobotcn www.DFRobot.
