User Manual

DGL Toys™ is an innovative division of DGL Group, Ltd.
Other trademarks and trade names are those of their respective owners.
DGL Toys,
195 Raritan Center Parkway, Edison, NJ 08837.
Specifications, colors and contents may vary from illustrations.
Manufactured in China.
Batch Ref: XXXX
Model Number: XXXX
Conforms to safety requirements of ASTM, FCC, & CPSIA.
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 years.
Tested to comply with FCC standards.
FOR HOME OR OFFICE USE.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
BATTERY WARNING:
• Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries should not be recharged.
• Rechargeable batteries should be removed from the appliance before being charged.
• Rechargeable batteries should be charged under adult supervision only.
• Exhausted batteries should be removed.
• The supply terminals should not be short-circuited.
• Only batteries of the same or equivalent type are recommended to be used.
• Batteries should be inserted with the correct polarity.
quadrone
Instruction Manual
Notice
Warnings
Included
Charging Your Drone
Installing the Camera
Installing the Landing Gear and Crash Guards
Flight Controls
Practice Tips
Trimming the Quad
Speed Selection
Headless Mode
Problem Cause Solution
Drone’s LED lights blink continuously
for more than 4 seconds after quad is
turned on. No response to controller.
No response after quad is turned on.
1. Replace batteries.
2. Reinstall batteries at correct
polarity.
Recharge quad battery.
Motor does not respond to throttle.
Motor spins but doesn’t take off.
Quad is making a loud vibration
noise.
Quad still wanders forward after trim
adjustment.
Forward trim is too high.
1. Lower forward trim.
2. Recalibrate drone.
Cannot fly after crash.
1. Motor fell out.
2. Gear loosened.
1. Reinstall motor.
2. Tighten gear.
Bent or damaged rotor blades.
1. Remote batteries have been
depleted.
2. Batteries are installed at
incorrect polarity.
1. Bent rotor blades.
2. Quad battery is depleted.
1. Replace damaged blade.
2. Recharge battery.
Replace damaged blade.
Battery has been depleted.
Unable to sync to
remote controller.
Repeat power
sequence and re-sync.
(See pg. 5)
Troubleshooting
Remote Controller Diagram
Remote Controller Battery Installation
Safety Notes
Additional Warnings and Precautions
• All instructions, warranties and other collateral documents are subject
to change at the sole discretion of our company.
• If this is your first time flying a quadcopter read the manual carefully.
Seek the help of an experienced pilot to help you fly. These safety
instructions are intended not only for the protection of your Quadrone
but also to protect your own safety. Improper operation can cause
injury or property damage.
• This product is suitable for indoor and outdoor use. Please make sure
you choose a flight area with no obstacles and maintain a safe distance
from people and pets. Do not operate near power lines.
• Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property or
cause serious injury. This is a sophisticated hobby product. It must be
operated with caution and common sense, and requires some basic
mechanical ability. Failure to operate this product in a safe and
responsible manner could result in injury or damage to the product or
property. This product is not intended for use by children without direct
adult supervision. This manual contains instructions for safety,
operation and maintenance. It is essential to read and follow all the
instructions and warnings in this manual, prior to assembly, set up or
use, in order to operate correctly and avoid damage or serious injury.
1. Age Recommendation: Not for children under 14 years of age. This is
not a toy.
2. Always operate in open spaces away from obstacles, people, and
hazards.
3. Always follow directions and warnings for this and any optional
equipment carefully. (chargers, rechargeable battery packs, etc)
4. Always keep small parts and electrical parts out of the reach of
children.
5. Always avoid water exposure to all equipment not specifically
designed and protected for this purpose. Moisture can cause damage
to electronics.
6. Never place any portion of the model in your mouth as it could cause
serious injury or even death.
7. Never operate your model with low batteries.
To install batteries, use the included screw driver to open the battery
cover. Rotate counter clockwise to loosen screw. Insert 4 AA batteries into
the remote. Make sure the batteries are installed in the correct polarity as
indicated in the controller. Do not mix old and new batteries or batteries
with different chemistries. Reattach battery cover. Rotate screw clockwise
to refasten.
Introduction
Table of Contents
• Thank you for choosing Quadrone! This is a four-axis aircraft that can
fly outdoors, in order to make it easier to control the aircraft. Please
carefully read this manual before operating your Quadrone. Please
keep this manual for future reference.
• Before your first flight, please take the time to carefully read this manual
containing important flight information which will help your first flight go
more smoothly.
Introduction 1
Table of Contents 1
Notice 1
Warning 2
Additional Warnings and Precautions 2
Safety Notes 2
Included 3
Remote Controller Diagram 4
Remote Controller Battery Installation 4
Charging Your Drone 5
Installing the Camera 5
Syncing the Quad and Remote 5
Flight Controls 6
Practice Tips 7
Trimming the Quad 8
Flips and Rolls 9
Speed Selection 9
Headless Mode 9
Auto Return 10
Taking Photo/Video 10
Changing the Blades 10
Troubleshooting 12
• RC models are composed of many precise electrical components. It is
important to keep the model and associated equipment away from
moisture and other contaminants. The introduction of exposure to
water or moisture in any form can cause the model to malfunction
or crash. Do not operate or expose to rain or moisture.
• To avoid a potential fire hazard from batteries, do not short, reverse
polarity, or puncture batteries. Battery charging should be done under
adult supervision at all times, at a location out of reach of children. Do
not mix Ni-Cad and Alkaline batteries.
• Make sure the batteries are installed correctly to ensure correct
polarity. If you do not plan to use your Quadrone for an extended
period of time, remove the batteries from the controller to avoid battery
leakage which may damage the controller. Please dispose depleted
batteries according to local laws and ordinances.
• Li-Polymer batteries have higher operational risks compared to other
batteries. It is imperative to follow proper operational guidelines. The
manufacturer and dealer assume no liability for accidental damages
caused by improper usage. Do not use any other charger other than
the supplied charger included in this packaging in order to avoid
potential fire or explosion. Do not crush, disassemble, burn,
or reverse polarity.
• RC models are made from various forms of plastic very susceptible to
damage or deformation due to extreme heat and cold temperatures.
Make sure not to store the model near any heat source or
adverse temperatures.
1. Slide the camera into the slots under the drone on the battery holder to
secure it to the drone.
2. Connect the camera by inserting the power cable into the slot on the
bottom of the drone.
1. To install the landing gear, simply insert the landing gear into the
bottom of the drone. The landing gear will snap in when fully inserted.
2. To install the crash guards, insert them into the slots at the end of each
arm. Use the provide srew and screwdriver to secure the guard
in place.
• If you are not going to use your Quadrone for an extended period of
time, please take out the batteries in your remote controller. Potential
battery leakage could occur and possibly damage the remote or create
a fire hazard.
• Use these recommended practice exercises to become a better
Quadrone pilot:
Flips and Rolls
• Your Quadrone can perform impressive flips
and rolls in midair. In order to do this, press
the flip button on your remote during flight.
Move the directional joystick in any direction
and the aircraft will perform a coinciding flip.
* If the trim buttons do not correct the
problem, you will have to recalibrate your
drone. To do so, place the Quadrone on a
flat surface. Hold the two joysticks down
and to the right as depicted in the figure.
The lights on the will begin to flash. Once
the lights on the quad stop blinking for two
seconds, recalibration is complete.
Changing the Blades
• If a blade breaks or falls off your Quadrone during a crash, it will be up
to you to repair it. Use the screwdriver included in the package to
remove the screw, detaching the propeller from the drone. Rotate
counter-clockwise to loosen. Remove the damaged blade from the
motor. You can now attach a new blade. It is important for the correct
blade to be put on the correct motor or the drone will not fly correctly. A
letter is marked on each blade to indicate which motor it should go on.
• When in Headless Mode, no matter what
direction the quadcopter faces, it will
respond according to the direction pushed
on the remote. (Forward on the remote will
make the quadcopter fly forward, even if it is
pointing in another direction.) To enter
Headless Mode, land the Quadrone on a flat
surface. Press the down on the Directional
Joystick. The remote will beep and the lights
on the quad will begin to flash. To exit
Headless Mode, simply press the joystick
again. The remote will beep again and all
lights will remain on and return to normal.
Slow Speed: 1 Beep
Medium Speed: 2 Beeps
Fast Speed: 3 Beeps
Full Speed: 4 Beeps
• If your Quadrone is leaning to or favoring a side, you may need to use
the trim feature to balance it out so it flies straight.
Elevation: Raise the Quadrone using the throttle joystick. Gradually
lower the Quadrone so it lands softly to the ground.
Direction: Move the Quadrone in a cross pattern using the directional
joystick. Move forward, backward, left, right, and back to its
original position.
Turning: Turn the Quadrone in a throttle joystick. Turn left and right
repeatedly, and back to its original position.
• To charge your Quadrone, first
disconnect the battery from the
drone and slide it out of its holder.
Plug the provided USB charger into
a USB port. A green light on the USB
charger will turn on. Now connect
the USB charger to the battery. The
light on the charger will turn red, indicating the battery is now
charging. The red light will turn green again once the charging
process has completed. Always charge your Quadrone under adult
supervision and out of the reach of children. Charging time is
approximately 30 minutes. When you are ready to fly your Quadrone
again, reinsert the battery into its slot on the bottom of the drone.
• Before flying your Quadrone, it is highly recommended that you
familiarize yourself completely with its controls. Read through the
instruction manual completely before attempting your first flight.
Remote Controller x1Quadrone Tumbler-9 x1 Camera x1
Extra Blades x4 Li-Polymer Battery x1USB Charger x1Screwdriver x1
Push up on the throttle
joystick. The Quadrone will
begin to ascend.
Pull down on the throttle
joystick. The Quadrone will
begin to descend.
Elevation
Push the directional joystick
to forward. The Quadrone
will fly forward.
Push the directional joystick
to the left. The Quadrone
will turn to left.
Forward/Backward
Push the directional joystick
to the right. The Quadrone
will fly to the right.
Push the directional joystick
to the left. The Quadrone
will fly to left.
Aileron
Push the throttle joystick to
the right. The Quadrone will
turn to right.
Push the throttle joystick to
the left. The Quadrone will
turn to left.
Turning
If the Quadrone leans
forward, press the Down
Forward/Backward Trim
button until it balances out.
If the Quadrone leans
forward, press the Up
Forward/Backward Trim
button until it balances out.
Forward/Backward
If the Quadrone leans to the
right, press the Left Aileron
Trim button until it straightens
out.
If the Quadrone leans to the
right, press the Left Aileron
Trim button until it straightens
out.
Aileron
A
B
A
B
A
1
2 3 4 5 6 7 8 9 10 11 12 13 14
Syncing the Quad and Remote
1. Insert the battery into the drone and connect its wires. Turn on the
drone and place it on a flat surface. The lights on the drone will begin
to flash. Do not move the Quadrone during the syncing process to
ensure the gyroscope stays balanced.
2. Lower the Throttle Joystick on the remote to its lowest position. Turn
the remote on. Push the Throttle Joystick to its highest position. The
lights on the Quadrone will stop flashing and stay on and the remote
will beep. You are now ready to fly your drone.
• Your Quadrone can fly at four speeds. To
select a speed, press the Speed Selection
button on your remote. Your remote will
beep each time you switch speeds.
Auto Return
• To enter Auto Return simply press the Auto
Return button while in Headless Mode. The
remote will beep and the lights on the quad
will begin to flash. The drone will being to fly
directly backwards towards the remote.To
exit Auto Return, press the button again
or press forward on the Directional Joystick.
Taking Photo/Video
• To take a photo, press up on the Photo/Video
button on the remote. The light on the
camera will flash and the remote will beep,
indicating a picture has been taken.
• To take a video, press down on the
Photo/Video button on the remote. The light
on the camera will flash continuously and the
remote will beep twice, indicating a video is
being recorded. Press down on the
Photo/Video button again to stop recording.
Throttle
Joystick
Speed Selection
Antenna
Power lndicator
Flip Button
Directional Joystick
Headless Mode (Press)
Forward/Backward
Trim Button
Alerion
Trim Button
Light Control (Left)
Auto Return (Right)
Power Switch
Photo Button (Up)
Video Button (Down)
Battery cover
4 Alkaline batteries
Flying: Once you have mastered the previous three exercises,
draw a circle on the ground. Practice flying within the
confines of the circle. Narrow the circle as your skills
progress.
See diagram below:
Once you have mounted the new blade, you can refasten it with the
screw. Rotate clockwise to tighten.
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. if this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Limited 90-Day Warranty
IMPORTANT NOTICE!
DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT
FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:
DGL Group. Ltd.
WARRANTY REPLACEMENT DEPARTMENT
TEL: [phone]
[e-mail]
REPAIR/REPLACE PRODUCT
PREPARATION FOR SHIPPING YOUR PRODUCT
DGL Group, Ltd. warrants to the original consumer that this product is free from
any electrical or mechanical defects for a period or 90 DAYS from the date of
purchase. If any such defect is discovered within the warranty period, DGL Group,
Ltd. will repair or replace the unit free of charge upon receipt of the unit, shipped
postage prepaid and insured to our warranty center. The warranty covers normal
consumer use and does not cover damage that occurs in shipment of failure that
results from alterations, accident, misuse, abuse, neglect, wear and tear, inade-
quate maintenance, commercial use or unreasonable use of the unit. Removal of
any parts/components voids all warranties. This warranty does not cover cost of
repairs made or attempted outside by third-party individuals and fitness, are
hereby limited to 90 DAYS from the date or purchase. Consequential or incidental
damages resulting from a breach of any applicable express or implied warranties
are hereby excluded. Some states do not allow limitations on the duration of
implied warranties and do not allow exclusion of incidental or consequential
damages, so the above limitations and exclusions in these instances may not
apply.
If your product begins to malfunction or stop working, immediately call or email
our warranty center at the phone/email listed below. If it is determined that a return
is necessary, our warranty department will issue you an RMA number/form and an
address to the nearest return center to ship the product to. IMPORTANT NOTICE:
We will reject all returns that are not accompanied by an issued RMA form and
number so make sure to contact our warranty center before attempting to return
your product!
Please repack your product in a durable box, preferably in the original carton, and
send it prepaid, and adequately insured. Include the RMA form that was issued by
our warranty department along with your daytime telephone number and email
address (if available) inside the shipping carton. If your warranty has expired,
contact our warranty center for charged service. For further information please
send all inquiries to
[e-mail]
• Follow community-based safety guidelines, as developed by organizations
such as the Academy of Model Aeronautics (AMA).
• Fly no higher than 400 feet and remain below any surrounding obstacles
when possible.
• Keep your drone in eyesight at all times, and use an observer to assist
if needed.
• Remain well clear of and do not interfere with manned aircraft operations,
and you must see and avoid other aircraft and obstacles at all times.
• Do not intentionally fly over unprotected persons or moving vehicles, and
remain at least 25 feet away from individuals and vulnerable property.
• Contact the airport or control tower before flying within five miles
of an airport.
• Do not fly in adverse weather conditions such as in high winds or
reduced visibility.
• Do not fly under the influence of alcohol or drugs.
• Ensure the operating environment is safe and that the operator is competent
and proficient in the operation of the drone.
• Do not fly near or over sensitive infrastructure or property such as power
stations, water treatment facilities, correctional facilities, heavily traveled
roadways, government facilities, etc.
• Check and follow all local laws and ordinances before flying over
private property.
• Do not conduct surveillance or photograph persons in areas where there is
an expectation of privacy without the individual’s permission.
WARNING!
To reduce the risk of fire or burns:
Do not disassemble, crush, puncture, or short external connectors contacts.
Use only with specified charger and player.
Do not dispose of in fire or water.
Do not expose to high temperature above 140° F (60 ° C).
Store between 32° F (0° C) and 140° F (60° C).
Keep away from children.
See operating instructions of this battery or product.
Batteries should be recycled or disposed of as per State and Local guidelines.
Safety Guidelines
Li-ion Battery
Must Be Disposed
Of Properly
AW-QDR-TBCAM
FCC ID:2AANZQDRTBCAM
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.