Installation Guide

2
PACKAGE CONTENTS
PREPARATION
SAFETY INFORMATION
Estimated Installation Time: 30 minutes
Tools Required for Installation (not included): #10 x 2-1/2-in Installation Screws, Phillips Screwdriver,
Drill, 3/32-in Drill Bit, Marking Tool, Carpenter’s Level, Tape Measure, Stud Finder and Staple Gun
(for shadow toekick installation only)
Itisrecommendedthisitembeinstalledtoatleast1wallstud.Useastudnder
(notincluded)tondthewallstud(s)atthedesiredinstallationsiteandmark
area(s) with a pencil (not included). Note: To make installation easier, remove all
doors and drawers from the vanity before installation.
WARNING
Please read and understand this entire manual before attempting to assemble, operate or install the product.
Do not stand on vanity. Use vanity on level ground. Base vanity supports a maximum weight of 200 lbs.
Exceeding maximum weight limit will compromise the integrity of the vanity structure and could cause
the vanity to fail.
CAUTION
Do not hang from the vanity.
PART DESCRIPTION QUANTITY
A Vanity Base 1
A
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
STEP 1: Wall Stud Location
INSTALLATION INSTRUCTIONS
1
HARDWARE CONTENTS
AA
AA
BB
CC
Knob
Qty. 1 per door/drawer
Shadow Toekick
(included with 39A, 39D, R17, S12 and S13
models only)
Qty.1
Plastic Toekick Braces
(included with 39A, 39D, R17, S12 and S13
models only)
Qty. 2 for 30-in and 36-in vanities;
3 for 48-in and 60-in vanities
Lowes.com
3
STEP 2: Vanity Drawer Removal
2a. Open the preassembled drawer as far as possible.
2b. Simultaneously press the right side spring clip downward
and the left side spring clip upward.
2c. Once both springs clips are held in the indicated position,
pull the drawer straight out.
STEP 3: Shadow Toekick Installation (Optional)
3a. Lay vanity base (A) on it’s top.
3b. Set shadow toekick (BB) back 3-in from front of vanity base (A).
3c. Use staple gun to secure shadow toekick (BB) to vanity base (A)
using plastic corner braces (CC).
3d. Place one corner brace vertically in each corner. For 48-in and
60-in vanities, add a 3rd corner brace horizontally in center.
STEP 6: Hinge Adjustment For Door Alignment
If the alignment of the preassembled doors on vanity base (A)
isoff,refertothegureontherightforhowtoadjust.
INSTALLATION INSTRUCTIONS
2
3
STEP 4: Vanity Base Installation
4a. Place vanity base (A) at the desired position.
4b. Drill through vanity back braces into wall studs using
a 3/32-in diameter drill bit (not included). Note: Holes
should come no closer than 2 inches from any inside edge.
4c. Insert installation screws (not included) through vanity base (B)
and into the holes and tighten securely.
4d. Install knobs (C) to the doors and drawers with the
preassembled hardware(AA).
4
STEP 5: Vanity Drawer Installation
5a. Close completely both slides attached to the vanity base (A).
5b. Move the component of the slides with ball bearings to the
front of the slides, still keeping the slides completely closed.
5c. Carefully line up the slides of the drawer box with the
slides in the vanity base (A) and push the drawer all the
way to the back.
5d. Open the drawer completely to ensure it is properly installed.
Simultaneously
press the right
spring clip
and left spring
clip to remove
drawer
5
Drill through
cabinet back
braces
B
Lowes.com
Placement for
all vanities
Placement
for 48-in
and 60-in
vanities
Adjustdoorheight
Adjustgapsbetween
doors and vanity
Adjustgapsbetweendoors
6
CARE AND MAINTENANCE
Vanity
Use non-abrasive cleaners and/or cleaning agents that do not contain solvents.