P/N: 500-087G Downloaded from www.Manualslib.
Wide LCD-TV Instruction Manual LT-40H6MVH ● LT-40T6MVH ● LT-46T6MVH ● Please read this manual carefully before operating your set. Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
Warnings WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : The unit is operated at dangerous voltages. The unit may only be opened by an authorised specialist. All maintenance and servicing work must be carried out by an authorised company. Repairs that are carried out incorrectly could result in fatal injuries to the user.
Warnings Cleaning Unplug the TV before cleaning the face of the LCD Screen. Dust the TV by wiping the screen and cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid or aerosol cleaners. POWER The main plug should be inserted fully into the power outlet to avoid a fire hazard. Hold the plug firmly when unplugging. If you pull the cord, the cord may be damaged. Prevent dust collecting on the power plug pins or outlet.
Warnings Safety This LCD TV have been engineered and manufactured to assure your safety. You can prevent serious electrical shock and other hazards by keeping in mind the following. Do not place anything heavy, wet or magnetic on the LCD TV or the power cord. Never cover the ventilation openings with any material and never touch them with metallic or inflammable materials. Avoid operating the LCD TV in extreme heat, humidity or areas affected by dust.
IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
IMPORTANT SAFETY INSTRUCTIONS 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.
Contents uBefore operating the set, please read this manual carefully.
Contents uBefore operating the set, please read this manual carefully.
Supplied Accessories uMake sure the following accessories are provided with Product. AC cord Batteries (2EA) Remote controller Wide LCD-TV Instruction Manual ● ● ● LT-40H6MVH LT-40T6MVH LT-46T6MVH Please read this manual carefully before operating your set. VGA cable Instruction manual PC AUDIO IN cable Battery installation uInserting batteries 1 Remove the battery cover by pulling it upward in the direction shown by the arrow. 2 Insert the batteries with correct polarity.
Installation Installation Options uYou can install the TV on a wall or place it on a table-like surface. uTo eliminate any risk of injury from the TV falling, it should be mounted securely. Wall Installation Do not install the TV on a weak wall surface, like plaster etc. Caution When the TV is placed into a cupboard, the distance between the TV and the wall have to leave minimum 60mm square as below.
Connecting Speaker L Connecting TV and Speaker(LT-40T6MVH/LT-46T6MVH) 1 Fix the bracket onto the guide pole located on the rear of TV and Speaker. speaker joint bracket 2 Clamp the speaker and the TV together fasten the screws. 3 Connecting the speaker audio cable to the external speaker output jack on the TV. External speaker output jack External speaker input jack 4 Fix the speaker audio cable on the quick clamp✽ located on the rear of TV.
Controls Front Panel CH [LT-40H6MVH] [LT-40T6MVH, LT-46T6MVH] 1. ON/OFF Switches TV set on or off. 2. MENU Displays a menu. 3. ▼CH▲ (Channel Up/Down) Selects a channel or a menu item. 4. ◀VOL▶ (Volume Up/Down) Adjusts the volume./ Adjusts menu settings. 5. TV/AV Selects TV, VIDEO, S-VIDEO, COMPONENT1, COMPONENT2, PC ANALOG, HDMI./ Clears the menu from the screen. 6. Power Indicator Illuminates in red when the TV is in standby mode./ Illuminates in green when the TV is switched on. 7.
Controls Rear Panel 1. PC ANALOG IN (D-SUB) 2. HDMI (High Definition Multimedia Interface) IN Connect to the HDMI jack for device with HDMI output. 3. PC AUDIO IN Connect the audio cable from the PC to the PC AUDIO IN of the set. 4. H/P (Headphone out) Connect a headphone to this socket. 5. Coaxial OUT Connect the coaxial audio cable from the digital audio device to the Coaxial OUT of the set. 6.
Controls All the functions can be controlled with the remote controller. Some functions can also be adjusted with the buttons on the side panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby or off to standby mode. 2. MUTE Turns the sound on and off. 3. NUMBER buttons Selects Channel numbers. 4. Hyphen (*only DTV mode) Press to select DTV channels.
Controls 15. SLEEP Sets the sleep timer. 16. Q.VIEW Returns to the previously viewed Channel. 17. PICTURE( ) Recalls your preferred picture setting. 18. SOUND( ) Recalls your preferred sound setting. 19. SAP Adjusts the MTS-stereo, Mono, SAP 20. CC Set the caption function. 21. LIST Displays the program list menu. 22. FAV+/Press to switch to your favorite channels. 23. PIP( ) Displays a PIP(Picture In Picture) screen. 24. INPUT( ) Selects the AV source of sub picture in PIP mode. 25.
Basic Operation Turning the TV On and Off Standby Setup: The AC power cord must be set up and connected to have the TV in standby mode ready to be turned on. Press the ON/OFF button on the front panel of the TV to go into standby mode. 1 If the TV is in standby mode, press the POWER button on the remote controller or the TV itself to turn the TV on. 2 Press the POWER button again on the remote controller or the TV itself to turn the TV off.
Basic Operation On screen menu language selection The menu can be displayed on the screen in desired language. First select your language. 1 Press the MENU button. 2 x/CHy y button. Select the Setup menu with CHx 3 Press the Ïq button to select the Setup menu. 4 x/CHy y button. Select the Language with CHx 5 Press the Ïq button to select the Language. 6 x/CHy y button to select your desired language. Press the CHx 7 Press the TV/AV button.
On Screen Menus and Display 1 Press the MENU button to display main menu. 2 x/CHy y button to select menus-Picture, Press the CHx Sound, Special, Setup. 3 Adjust each menu with the Ïq button. 4 Press the MENU button to return to preceding menu. 5 Press the TV/AV button to finish adjusting menu.
Setting up TV Program Once you have preset the program, you will be able to use the x/CHy y or NUMBER buttons to scan the program you CHx programmed. Program can be tuned using Auto or Manual program menu. Auto Program All programs that can be received are stored by this method. It is recommended that you use Auto program during installation of this set. 1 Press the MENU button. 2 Select the Setup menu. 3 Select the Auto Program menu. 4 xy button to select Table mode. Select the CHx 5 Ïq button.
Setting up TV Program Manual Program Manual Program lets you manually tune and arrange the Channels in whatever order you desire. Also you can assign a Channel name with 8 characters to each channel number. Channel Table V/UHF Name 1 Press the MENU button. Finetune 2 Select the Setup menu. Memorize 3 Select Manual Program menu. 4 xy button to select Channel . Press the CHx 5 Select the Table menu. Then select a tuner mode with the Ïq button.
Picture Control You can adjust Color Temperature, Contrast, Brightness, Color, Sharpness and Tint(Only in NTSC mode) to the levels you prefer. Manual Picture Control Picture Color Temperature 1 Press the MENU button. 2 x/CHy y button, and Select Picture using the CHx Contrast Select Color Temperature using the Ïq button. Picture Color Temperature Picture Color Temperature Contrast Brigheness Color Sharpness 4 x/CHy y button to select a particular color tone.
Picture Control PICTURE Effect 1 Press the PICTURE( ) button. 2 Press the PICTURE( ) button repeatedly to select Picture effect. Each press of the button changes the screen display as below.
Sound Control You can select your preferred sound setting; Flat, Music, Movie or Speech and you can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level even if you change program. Manual Sound Control 1 Press the MENU button. 2 x/CHy y button, and press Select the Sound using the CHx the Ïq button. 3 x/CHy y button to select the desired sound item; Press the CHx Equalizer, Balance, AVL, SRS WOW or Headphone Volume.
Sound Control SOUND Effect 1 Press the SOUND( ) button. 2 Press the SOUND( ) button repeatedly to select. Each press of the button changes the screen display as below. Flat Music Movie Speech User SRS WOW Auto Sound Control * The sound Flat, Music, Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. 25 Downloaded from www.Manualslib.
Parental Control If used, this optional feature can “block” undesirable programming from appearing on the TV. Parental Control offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating they consider accept-able, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password.
Parental Control Setup TV Rating 1. Press the MENU button. 2. Select the Setup menu. 3. Press the CHxy button to select the Parental Control, then press the Ïq button. 4. The “Enter Password” screen will appear. Enter your 4-digit password. Note : The default Input password for a new TV set is “0000”. 5. After entering a valid Enter password, the “Parental Control” screen will appear.
INFORMATION MOTION PICTURE ASSOCIATION OF USA (MPAA) RATING SYSTEM Grade Meaning G General Audiences Content not offensive to most viewers PG Parental Guidance Suggested Content is such that parents may not want their children to view the program. PG-13 Parental Strongly Cautioned Program is inappropriate for preteens, with a greater degree of offensive material Suggested than a PG rated program R Restricted viewing Not for children under age 17. Strong elements of sex and/or violence.
INFORMATION The sub-rating of TV rating Grade Meaning FV Fantasy Violence V Violence S Sexual Situation L Adult Language D Sexual Suggestive Dialog Note ; The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to change. To set the FV, D, L, S and V sub-ratings, first select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 and TV-MA Next, while the TV-Ratings is highlighted, repeatedly press the Ïq buttons. This will cycle through the available sub-ratings(FV, D, L, S or V).
Captions The captions is a process which converts the audio portion of a television program into written words which then appear on the television screen in a form similar to subtitles. Closed captions allow viewers to read the dialogue and narration of television programs. Shooting... Goal in..... Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance.
Other functions Clock Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time. 1 Press the MENU button. x/CHy y button to select the Setup menu. 2 Press the CHx Then press the Ïq button. x/CHy y button to select Clock menu. 3 Press the CHx Then press the Ïq button. Parental Control Caption Off Setup Clock x/CHy y or number buttons Set the present time with the CHx on remote controller.
Other functions N.R.(Noise Reduction) The N.R feature improves the picture quality by setting to Mode1 or Mode2. If you experience noise on a certain program, set the N.R to Mode1 or Mode2 for this program, to obtain the optimum picture. 1 Press the MENU button, select the Special. 2 Press the Ïq button to select N.R.. 3 Press the Ïq button to select Off, Mode1 or Mode2. 4 Press the TV/AV button to return to normal TV viewing.
Other functions Childlock Childlock menu is necessary in order to disable the buttons on the front/side panel of the set. Especially it is useful to prevent unauthorized viewing. x/CH button to select Childlock. 1 Press the CHx Ï q 2 Press the button repeatedly to select On or Off. * When the setting is Childlock On, the buttons except ON/OFF button on the front/side panel of the set is disabled. * When the setting is Childlock Off, the buttons on the front/side panel of the set is enabled.
Other functions Sleep timer You don’t have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set to standby after the preset time elapses. Press the SLEEP button to select the number of minutes. The display will appear on the screen, followed by 0, 15, 30, 60, 120. The timer begins to count down from the number of minutes selected. Note a. To view the remaining sleep time, press the SLEEP button once. b.
Other functions Calling the program list You can check the programs stored in the memory by displaying the program list. Displaying program list 1 Press the LIST button to display the Program list menu. The program list appears on the screen. One program list page contains twenty programs as right picture. Note a. You may find some blue programs. They have been set up to be skipped by auto programming or in the program edit mode. b.
External Equipment Connection You can connect additional equipment, such as VCRs, camcorders etc. to your set. Examples are shown below. Antenna connection Connect RF out on the VCR to the Antenna input on the rear of the TV. A/V IN 1 Connect the A/V out jacks on a VCR to A/V-IN jacks on the TV. 2 Press the TV/AV button to select VIDEO mode. 3 Press the PLAY button on the VCR. The VCR playback picture appears on the TV screen.
External Equipment Connection You can connect additional equipment, such as VCRs, camcorders etc. to your set. Examples are shown below. A/V OUT 1 Connect the Audio outputs(L, R) of the TV to Audio-IN(L, R) of another displayer or the amplifier system. - If you connect the amplifier system, you can also play the TV sound through the stereo amplifier system. 2 Connect the Video output of the TV to Video IN of another displayer.
External Equipment Connection Connecting to HDMI (High Definition Multimedia Interface) 1 Connect an HDMI cable between the “HDMI IN” jack on the TV and the HDMI OUT jack on the set-top box. Please check that the HDMI source is powered on. 2 Press the TV/AV button to select HDMI mode. S-VIDEO IN If the optional equipment you are connecting has an S-VIDEO jack, you can use an S-VIDEO cable for improved picture quality(compared to an A/V cable).
Connecting the PC as a monitor This function is possible only when the set is in PC mode. Use the TV/AV or TV/PC button on remote controller. Picture adjustment You can adjust picture Color Temperature, Contrast, Brightness, Color, Sharpness and ARC as you prefer. 1 2 Press the TV/AV button to select the COMPONENT 1, COMPONENT 2, PC- ANALOG or HDMI mode. Press the MENU button. 3 Select the Picture. 4 Select Color Temperature using the Ïq button. 5 x/CHy y button to select a particular color tone.
Connecting the PC as a monitor Sound adjustment 1 Press the MENU button. 2 Select the Sound menu. 3 x/CHy y button to select the desired sound item; Press the CHx Equalizer, Balance, AVL, SRS WOW, Headphone or Input. 4 Press the Ïq button to make desired adjustment. 5 Press the Ïq button in Equalizer to set the Equalizer. 6 x/CHy y button to select your Press the CHx preferred setting ; Flat, Music, Movie, Speech or User. To set the Equalizer User. x/CHy ybutton. a.
Connecting the PC as a monitor Setup This function is to adjust picture to left/right and up/down as you prefer. 1 Press the MENU button. 2 Select the Setup menu. 3 x/CHy y button to select the desired item. Press the CHx 4 Press the Ïq button to make desired adjustment. 5 Press the TV/AV button to exit menu H-Position (Horizontal Position) This function is to adjust picture to left/right as you prefer. V-Position(Vertical Position) This function is to adjust picture to up/down as you prefer.
Connecting the PC as a monitor PC INPUT 1 Connect the PC IN cable (D sub cable) from the monitor output socket of the PC to the PC ANALOG IN socket of the set. 2 Connect the PC AUDIO IN cable from the PC to the PC AUDIO IN of the set. 3 Press the TV/AV or TV/PC button to select PC-ANALOG mode. 4 Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor. Resolution Mode Resolution Horizontal frequency (KHz) Vertical frequency (Hz) VGA 640 x 480 31.
Product Specifications Model LT-40T6MVH/LT-40H6MVH LT-46T6MVH Television system NTSC Television program VHF: 2~13 UHF :14~69 Cable : 01~125 LCD Panel 40" Wide TFT LCD Panel Resolution WXGA(1366 x 768) Power consumption 46" Wide TFT LCD 220W 270W External antenna impedance 75Ω Audio output 10W +10W External IN/OUT ports AC Input ★ • HDMI IN • S-VIDEO IN • HEADPHONE JACK • PC-ANALOG IN • PC AUDIO IN • A/V IN IN • A/V OUT IN • COAXIAL OUT • ANTENNA IN • COMPONENT 1 IN • COMM.
Troubleshooting Problem Check item No picture on screen and no sound from speakers. • Make sure the remote control is not in the standby mode (The POWER/Standby indicator is red.) • Turn on the MAIN POWER button on the top of the display. No picture/No picture from AV terminal. • Check the brightness setting of the display. • Lamp may have malfunction. • Make sure a cable with no VIDEO input signal is connected to the S-VIDEO INPUT terminal. Picture is displayed, but no sound from the speakers.
Memo 45 Downloaded from www.Manualslib.
Memo Downloaded from www.Manualslib.
Memo Downloaded from www.Manualslib.
