USB 2.0 LAN Docking Station Replicator 2.O english User’s Guide USB 2.0 LAN Docking Station deutsch Bedienungsanleitung USB 2.0 LAN Docking Station français Guide d’utilisation Station d’accueil USB 2.0 LAN español Manual de instrucciones USB 2.0 LAN Docking Station italiano Manuale d’uso Stazione di docking USB 2.0 per LAN www.dicota.
english Table of contents Introduction ...................................................... Driver installation .............................................. Making sure installation was successful ................ Removing drivers .............................................. Notes • For the Replicator 2.0 working under stable environment, please be sure to use the power adaptor. • When the USB 2.0 HUB ports become overloaded, please refresh or re-plug the Replicator 2.
Step 4: Click “Next” to continue. Step 6a: Select “Yes” and click “Finish”. Step 5a: Click “Yes” to continue. (Under Windows 2000) Step 6b: Click “Finish” to complete the driver installation. Step 5b: Click “Continue Anyway” to continue.
Step 7a: • Plug the USB A type of USB 2.0 cable Replicator 2.0. • Plug the USB B type of USB 2.0 cable into the USB 2.0 HUB ports of your PC or Notebook. • Click “Yes” to continue. (Under Windows 2000) Step 8: Click “Continue Anyway” to continue. Step 9: Click “Finish” to complete the “ADM851X USB To Fast Ethernet Adapter” driver installation. Step 7b: • It will show a new hardware device “ADM851X USB To Fast Ethernet Adapter”. (Under Windows XP) • Select “Install the software automatically” item.
Make sure the installation was successfully Driver un-installation • Windows 2000/XP • Windows 2000/XP Step 1: • To make sure you have installed the Replicator 2.0 successfully, please move the cursor to “My computer” → “Control Panel” → “System Properties” → “Hardware” → “Device Manager”. • Double click the “Human Interface Devices”; it will show the “HID-compliant device” x 2 and “USB Human Interface” x 2. • Double click the “Keyboards”; it will show the “HIDkeyboard Device”.
Step 3: Click “Finish” to complete the driver un-installation. Cerificate FCC This equipment has been tested and found to comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: • this device may not cause harmful interference • this device must accept any interference received. Including interference that may cause undesired operation. CE-Certificate This equipment is in compliance with the requirements of the following regulations: EN 55 022: CLASS B.
deutsch • Für einen stabilen Betrieb des Replicator 2.0 verwenden Sie bitte das mitgelieferte Netzteil. • Wenn es zu einer Überlastung der Anschlüsse des USB 2.0 HUBs kommt, führen Sie ein Reset des Replicator 2.0 durch, oder trennen Sie diesen kurzzeitig vom Notebook und schließen Sie ihn anschließend wieder an. Inhalt Einführung ........................................................ 7 Installieren der Treiber........................................ 7 Überprüfen der erfolgreichen Installation .........
Schritt 4: Klicken Sie auf „Weiter“, um fortzufahren. Schritt 6a: Klicken Sie auf „Ja“ und anschließend auf „Fertig stellen“. Schritt 5a: Klicken Sie auf „Ja“, um fortzufahren. (Unter Windows 2000). Schritt 6b: Klicken Sie auf „Fertig stellen“ um die Installation zu beenden.
Schritt 7a: • Stecken Sie den USB-Stecker Typ A (flacher Stecker) von einem USB-Kabel Version 2.0 in den Replicator. • Stecken Sie den USB-Stecker Typ B von dem USBKabel Verson 2.0 in einen freien Port Ihres Rechners oder Notebooks ein. • Klicken Sie auf „Ja“, um fortzufahren. (Unter Windows 2000). Schritt 8: Klicken Sie auf „Trotzdem fortfahren“, um fortzufahren. Schritt 9: Klicken Sie auf „Fertigstellen“, um die Installation des „ADM851X USB To Fast Ethernet Adapter“-Treibers abzuschließen.
Überprüfen der erfolgreichen Installation Deinstallieren der Treiber • Windows 2000/XP • Windows 2000/XP Schritt 1: • Um zu überprüfen, ob die Installation des Replicator 2.0 erfolgreich war, wählen Sie „Arbeitsplatz“ → „Systemsteuerung“ → „System“ → „Hardware“ → „Gerätemanager“. • Durch Doppelklicken auf „Eingabegeräte (Human Interface Devices)“ werden je zwei Einträge für „HID-konformes Gerät“ und „USB-Eingabegerät“ angezeigt.
Step 3: Klicken Sie auf „Fertig stellen“, um die Deinstallation abzuschließen. Zertifikate FCC Dieses Gerät wurde getestet und entspricht dem Part 15 der FCC Regularien. Der Betrieb des Geräts unterliegt zwei Bedingungen: • Das Gerät darf keine schadhafte Störungen hervorrufen. • Das Gerät muß jede Art von Störung akzeptieren, auch dann wenn diese Störung den eigenen Betrieb einschränkt. Haftungsausschluß Die Information in diesem Dokument kann sich ohne Vorankündigung ändern.
français Table des matières Introduction .................................................... Installation du pilote.......................................... Vérification de l’installation ................................ Désinstallation des pilotes ................................ Remarques • Pour une utilisation stable du Replicator 2.0 , veuillez utiliser l’adaptateur secteur fourni. • Quand les ports du HUB USB 2.0 sont surchargés, veuillez actualiser ou débrancher puis rebrancher le Replicator 2.
Étape 4: Cliquez sur «Suivant» pour continuer. Étape 6a: Cliquez sur «Oui», puis sur «Terminer». Étape 5a: Cliquez sur «Oui», puis sur «Terminer». (sous Windows 2000) Étape 6b: Cliquez sur «Terminer» pour terminer l’installation.
Étape 7a: • Raccordez le port USB de type A du câble USB 2.0 du Replicator 2.0. • Raccordez le port USB de type B du câble USB 2.0 sur les ports du HUB USB 2.0 de votre PC ou ordinateur portable. • Cliquez sur «Oui» pour continuer. (Sous Windows 2000) Étape 8: Cliquez sur «Continuer» pour poursuivre. Étape 9: Cliquez sur «Terminer» pour terminer l’installation du pilote du périphérique «ADM851X USB To Fast Ethernet Adapter».
Vérification de l’installation Désinstallation des pilotes • Windows 2000/XP • Windows 2000/XP Étape 1: • Pour vérifier l’installation réussie du Replicator 2.0, veuillez déplacer votre curseur sur «Poste de travail» → «Panneau de configuration» → «Système» → «Matériel» → «Gestionnaire de périphériques».
Étape 3: Cliquez sur «Terminer» pour terminer la désinstallation du pilote. Certifications FCC Cet appareil a fait l’objet d’essais et est conforme aux dispositions du chapitre 15 du réglement de la FCC. Son utilisation est soumise aux deux conditions suivantes: • Cet appareil ne peut pas provoquer d’interférences nuisibles.
español Índice Introducción .................................................... Instalación de controladores .............................. Comprobación de que la instalación ha sido correcta .............................................. Eliminación de controladores ............................ Notas • Para un uso estable de Replicator 2.0, utilice el adaptador de CA suministrado. • Cuando se produce una sobrecarga de los puertos del concentrador USB 2.
Paso 4: Haga clic en “Siguiente” para continuar. Paso 6a: Haga clic en “Sí” y en “Finalizar”. Paso 5a: Para continuar haga un clic en “Sí” (bajo Windows 2000) Paso 6b: Para concluir la instalación haga un clic en “Terminar”.
Paso 7a: • Ponga el chufe USB tipo A (enchufe plano) de un cable USB versión 2.0 en el Replicator. • Ponga el enchufe USB tipo B del cable USB versión 2.0 en un portal de su ordenador o portátil. • Para continuar haga un clic en “Sí”. (Bajo Windows 2000). Paso 8: Para seguir haga un clic en “Continuar a pesar de todo”. Paso 9: Haga un clic en “Concluir” para cerrar la instalación del adaptador “ADM851X USB to Fast Ethernet Adapter”. Paso 7b: • Después es mostrado “ADM851X USB to Fast Ethernet Adapter”.
Comprobación de que la instalación ha sido correcta Eliminación de controladores • Windows 2000/XP Paso 1: • Menú Inicio: Haga clic en “Inicio” → “Panel de control” → “Agregar o quitar programas” (sólo Windows XP Menú Inicio clásico: Haga clic en “Inicio” → “Configuración” → “Panel de control” → “Agregar o quitar programas” (sólo Windows 2000/XP) • Seleccione el elemento “Replicator 2.0”. • Haga clic en el botón “Cambiar o quitar”.
Paso 3: Haga clic en “Finalizar” para completar la desinstalación del controlador. Certificaciones FCC Este aparato ha sido probado y responde a la parte 15 de las regulaciones FCC. El funcionamiento del aparato está sujeto a dos condiciones: • El aparato no debe originar perturbaciones nocivas. • El aparato debe aceptar todo tipo de perturbación, incluso si la perturbación limita el propio funcionamiento.
italiano Sommario Introduzione .................................................... Installazione dei driver ...................................... Verifica dell’installazione .................................... Rimozione dei driver ........................................ Note • Per assicurare il corretto funzionamento di USB 2.0 Port Replicator II, utilizzare l’adattatore fornito. • Se si verifica un sovraccarico delle porte dell’HUB USB 2.
Passaggio 4: Fare clic su “Avanti” per continuare. Passaggio 6a: Fare clic su “Si” e quindi su “Fine”. Passaggio 5a: Clic su “Si” per proseguire. (con Windows 2000) Passaggio 6b: Clic su “Continuare ugualmente” per completare l'installazione. Passaggio 5b: Cliccate “Continuare” per continuare (sotto Windows XP).
Passaggio 7a: • Collegate il connettore USB di tipo A (connettore piatto) del cavo USB versione 2.0 al Replicator. • Collegate il connettore USB di tipo B del cavo USB versione 2.0 a una porta abilitata del vostro calcolatore o Notebook. • Cliccate sul tasto “Sì” per continuare. (con Windows 2000). Passaggio 8: Cliccate “Continuare” per continuare. Passaggio 9: Cliccate sul tasto “Completare”, per concludere l’installazione del driver “ADM851X USB To Fast Ethernet Adapter”.
Verifica dell'installazione Rimozione dei driver • Windows 2000/XP • Windows 2000/XP Passaggio 1: • Per verificare che Replicator 2.0 sia stato installato correttamente, selezionare “Risorse del computer” → “Panello di controllo” → “Sistema” → “Hardware” → “Gestione periferiche”. • Fare doppio clic su “Human Interface Device (HID)”: verranno visualizzate due opzioni per “Periferica compatibile HID” e due opzioni per “Periferica USB Human Interface”.
Passaggio 3: Fare clic su “Fine” per completare la disinstallazione dei driver. Certificazioni FCC L’apparecchio è stato collaudato e risponde alla parte 15 del regolamento FCC. L’esercizio dell’unità presuppone due condizioni: • L’apparecchio non deve provocare interferenze dannose. • L’apparecchio deve essere in grado di resistere a ogni tipo di interferenza, anche se questa interferenza limita il proprio esercizio.