410BT Series Bluetooth® Battery Powered Irrigation Controller 410BT-ASV | 410BT-MVA I N S T R U C T I O N M A N U A L FCC certified | Bluetooth® certified | Waterproof | 3-year Limited Warranty
1. INTRODUCTION 5. ANTI-SIPHON VALVE COMPONENT IDENTIFICATION Thank you for purchasing DIG’s 410BT Single Station Battery Operated Controller. This manual describes how to get the 410BT series controller up and running quickly. After reading this manual and becoming familiar with the basic functionality of the controller, use the manual as a reference for less common tasks in the future. Lid FCC label One button for manual run and reset Battery compartment cap 2.
Additional control valves must not be installed downstream of the antisiphon valve. The valve must not be operated continuously for more than 12 hours in any 24-hour period. Consult local codes for specific details. Figure 5a Figure 5b 1. Flush main line until water runs clear before installation. 2. Shut off main water supply. 3. Install the anti-siphon valve directly to PVC pipe using 3⁄4 in. PVC male adapters (Figure 5a and 5b) or use 3/4 in. schedule 80 nipple.
6. MVA INSTALLATION 6.1 CHANGING ACTUATOR ADAPTERS The 410BT-MVA timer is factory set to fit a 3/4 in. brass manual antisiphon valve. To install the controller with actuator on a 1 in. manual anti-siphon valve, the 3/4 in. seat washer and adapter must be removed and replaced with the 1in. adapter and seat washer, which are included in this box. 1. Turn the actuator so that the seat washer and the 3/4 in. threaded adapter face up. 2. Using pliers, or a 5/16 in.
6.2 MANUAL VALVE ACTUATOR INSTALLATION Rated operating pressure: 20 to 125 PSI Recommended operating pressure: 20 to 80 PSI 6. Turn on main water supply. 7. Activate the solenoid through the timer manual button, a click will be heard indicating the valve is open. 1. Shut off main water supply. 2. Remove the manual stem from the existing valve and temporarily remove the anti-siphon cap (Fig. A). 3. Replace any existing worn washers with the new ones provided (Fig. B). 4.
APP SCREENS OVERVIEW The DIG BTT app automatically scans for nearby controllers after installation. Any DIG Bluetooth® controllers within 50′ (15 meters) line of sight will appear on screen. • Your new controller will appear as the BT Controller. Its default image, status (watering -on- or not watering -off-), connection strength, and battery life will appear alongside it. • Tap on the controller to connect to it and start programming.
HOME SCREEN Once connected, the Home screen will appear. This screen has everything needed to program the controller. By default, the controller’s Program is off. To turn it on, push the switch under the “Program” area. It will turn green and the Program area will light up indicating that the program is active and can now be modified. The controller is now ready to be programmed. Simply select the schedule (weekly, even/odd, or cyclical), set your start date or days, add times, and set a duration.
CONTROLLER SETTINGS The controller’s Settings screen contains everything else needed to fully control your irrigation system. It can be reached by selecting the Controller Settings button on the bottom of the screen.
MANUAL RUN The Manual Run screen allows for manual operation of the controller. It can be reached by selecting the Manual Run button on the bottom right of the screen. To manually run the controller, tap the button on the right of the screen. This button can also be used to stop any existing run. The default manual run time is for five minutes; this can be changed by tapping on the time and changing it. The controller can also manually run from the controller itself by tapping the water droplet button .
RESET TO FACTORY DEFAULTS • Press and hold the button on the 410BT for 15 seconds. This will remove all app settings, historical information, and any set passwords. This is the only way to remove a password so try not to forget it! TECHNICAL ASSISTANCE Should you encounter any problem(s) with this product or if you do not understand its many features, please refer to this operating manual first.
WARRANTY DIG CORPORATION warrants these products to be free from defects in material and workmanship for a period of three years from date of purchase. This warranty does not cover damage resulting from accident, indoor uses, misuse, neglect, modification, improper installation or subjection to line pressure more than 125 lbs. per square inch for anti-siphon valves, in-line valves and from an actuator. This warranty shall extend only to the original purchaser of the product for use by the purchaser.